4.4BSD/usr/src/contrib/gdb-4.7.lbl/gdb/tm-h8300.h
/* Parameters for execution on a H8/300 series machine.
Copyright (C) 1992 Free Software Foundation, Inc.
This file is part of GDB.
This program is free software; you can redistribute it and/or modify
it under the terms of the GNU General Public License as published by
the Free Software Foundation; either version 2 of the License, or
(at your option) any later version.
This program is distributed in the hope that it will be useful,
but WITHOUT ANY WARRANTY; without even the implied warranty of
MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
GNU General Public License for more details.
You should have received a copy of the GNU General Public License
along with this program; if not, write to the Free Software
Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA. */
/* Contributed by Steve Chamberlain sac@cygnus.com */
#define UNSIGNED_SHORT(X) ((X) & 0xffff)
#define EXTRA_FRAME_INFO \
struct frame_saved_regs *fsr; \
CORE_ADDR from_pc; \
CORE_ADDR args_pointer;\
CORE_ADDR locals_pointer ;
/* Zero the frame_saved_regs pointer when the frame is initialized,
so that FRAME_FIND_SAVED_REGS () will know to allocate and
initialize a frame_saved_regs struct the first time it is called.
Set the arg_pointer to -1, which is not valid; 0 and other values
indicate real, cached values. */
#define INIT_EXTRA_FRAME_INFO(fromleaf, fi) \
init_extra_frame_info (fromleaf, fi)
extern void init_extra_frame_info ();
#define IEEE_FLOAT
/* Define the bit, byte, and word ordering of the machine. */
#define TARGET_BYTE_ORDER BIG_ENDIAN
#undef TARGET_INT_BIT
#define TARGET_INT_BIT 16
#undef TARGET_PTR_BIT
#define TARGET_PTR_BIT 16
/* Offset from address of function to start of its code.
Zero on most machines. */
#define FUNCTION_START_OFFSET 0
/* Advance PC across any function entry prologue instructions
to reach some "real" code. */
#define SKIP_PROLOGUE(ip) {(ip) = h8300_skip_prologue(ip);}
extern CORE_ADDR h8300_skip_prologue ();
/* Immediately after a function call, return the saved pc.
Can't always go through the frames for this because on some machines
the new frame is not set up until the new function executes
some instructions. */
#define SAVED_PC_AFTER_CALL(frame) \
UNSIGNED_SHORT(read_memory_integer (read_register (SP_REGNUM), 2))
/* Stack grows downward. */
#define INNER_THAN <
/* Sequence of bytes for breakpoint instruction.
This is a TRAP instruction. The last 4 bits (0xf below) is the
vector. Systems which don't use 0xf should define BPT_VECTOR
themselves before including this file. */
#define BPT_VECTOR 0xf
#define BREAKPOINT {0x4e, (0x40 | BPT_VECTOR)}
/* If your kernel resets the pc after the trap happens you may need to
define this before including this file. */
#define DECR_PC_AFTER_BREAK 0
/* Nonzero if instruction at PC is a return instruction. */
/* Allow any of the return instructions, including a trapv and a return
from interupt. */
#define ABOUT_TO_RETURN(pc) ((read_memory_integer (pc, 2) & ~0x3) == 0x4e74)
/* Return 1 if P points to an invalid floating point value. */
#define INVALID_FLOAT(p, len) 0 /* Just a first guess; not checked */
/* Say how long registers are. */
#define REGISTER_TYPE unsigned short
# define NUM_REGS 10
# define REGISTER_BYTES (10*2)
/* Index within `registers' of the first byte of the space for
register N. */
#define REGISTER_BYTE(N) ((N) * 2)
/* Number of bytes of storage in the actual machine representation
for register N. On the H8/300, all regs are 2 bytes. */
#define REGISTER_RAW_SIZE(N) 2
/* Number of bytes of storage in the program's representation
for register N. On the H8/300, all regs are 2 bytes. */
#define REGISTER_VIRTUAL_SIZE(N) 2
/* Largest value REGISTER_RAW_SIZE can have. */
#define MAX_REGISTER_RAW_SIZE 2
/* Largest value REGISTER_VIRTUAL_SIZE can have. */
#define MAX_REGISTER_VIRTUAL_SIZE 2
/* Nonzero if register N requires conversion
from raw format to virtual format. */
#define REGISTER_CONVERTIBLE(N) 1
/* Convert data from raw format for register REGNUM
to virtual format for register REGNUM. */
/*#define REGISTER_CONVERT_TO_VIRTUAL(REGNUM,FROM,TO) */
/* Convert data from virtual format for register REGNUM
to raw format for register REGNUM. */
/*#define REGISTER_CONVERT_TO_RAW(REGNUM,FROM,TO) */
/* Return the GDB type object for the "standard" data type
of data in register N. */
#define REGISTER_VIRTUAL_TYPE(N) builtin_type_unsigned_short
/* Initializer for an array of names of registers.
Entries beyond the first NUM_REGS are ignored. */
#define REGISTER_NAMES \
{"r0", "r1", "r2", "r3", "r4", "r5", "r6", "sp","ccr","pc"}
/* Register numbers of various important registers.
Note that some of these values are "real" register numbers,
and correspond to the general registers of the machine,
and some are "phony" register numbers which are too large
to be actual register numbers as far as the user is concerned
but do serve to get the desired values when passed to read_register. */
#define FP_REGNUM 6 /* Contains address of executing stack frame */
#define SP_REGNUM 7 /* Contains address of top of stack */
#define CCR_REGNUM 8 /* Contains processor status */
#define PC_REGNUM 9 /* Contains program counter */
/* Store the address of the place in which to copy the structure the
subroutine will return. This is called from call_function. */
/*#define STORE_STRUCT_RETURN(ADDR, SP) \
{ write_register (0, (ADDR)); abort(); }*/
/* Extract from an array REGBUF containing the (raw) register state
a function return value of type TYPE, and copy that, in virtual format,
into VALBUF. */
#define EXTRACT_RETURN_VALUE(TYPE,REGBUF,VALBUF) \
bcopy ((char *)(REGBUF), VALBUF, TYPE_LENGTH(TYPE))
/* Write into appropriate registers a function return value
of type TYPE, given in virtual format. Assumes floats are passed
in d0/d1. */
#define STORE_RETURN_VALUE(TYPE,VALBUF) \
write_register_bytes (0, VALBUF, TYPE_LENGTH (TYPE))
/* Extract from an array REGBUF containing the (raw) register state
the address in which a function should return its structure value,
as a CORE_ADDR (or an expression that can be used as one). */
#define EXTRACT_STRUCT_VALUE_ADDRESS(REGBUF) (*(CORE_ADDR *)(REGBUF))
/* Describe the pointer in each stack frame to the previous stack frame
(its caller). */
/* FRAME_CHAIN takes a frame's nominal address
and produces the frame's chain-pointer.
However, if FRAME_CHAIN_VALID returns zero,
it means the given frame is the outermost one and has no caller. */
/* In the case of the H8/300, the frame's nominal address
is the address of a 2-byte word containing the calling frame's address. */
/* Use the alternate method of avoiding running up off the end of
the frame chain or following frames back into the startup code.
See the comments in objfile.h */
#define FRAME_CHAIN_VALID_ALTERNATE
/* Define other aspects of the stack frame. */
/* A macro that tells us whether the function invocation represented
by FI does not have a frame on the stack associated with it. If it
does not, FRAMELESS is set to 1, else 0. */
#define FRAMELESS_FUNCTION_INVOCATION(FI, FRAMELESS) \
(FRAMELESS) = frameless_look_for_prologue(FI)
/* Any function with a frame looks like this
SECOND ARG
FIRST ARG
RET PC
SAVED R2
SAVED R3
SAVED FP <-FP POINTS HERE
LOCALS0
LOCALS1 <-SP POINTS HERE
*/
#define FRAME_SAVED_PC(FRAME) frame_saved_pc(FRAME)
#define FRAME_ARGS_ADDRESS(fi) frame_args_address(fi)
#define FRAME_LOCALS_ADDRESS(fi) frame_locals_address(fi);
/* Set VAL to the number of args passed to frame described by FI.
Can set VAL to -1, meaning no way to tell. */
/* We can't tell how many args there are
now that the C compiler delays popping them. */
#define FRAME_NUM_ARGS(val,fi) (val = -1)
/* Return number of bytes at start of arglist that are not really args. */
#define FRAME_ARGS_SKIP 0
/* Put here the code to store, into a struct frame_saved_regs,
the addresses of the saved registers of frame described by FRAME_INFO.
This includes special registers such as pc and fp saved in special
ways in the stack frame. sp is even more special:
the address we return for it IS the sp for the next frame. */
#define FRAME_FIND_SAVED_REGS(frame_info, frame_saved_regs) \
frame_find_saved_regs(frame_info, &(frame_saved_regs))
/* Push an empty stack frame, to record the current PC, etc. */
/*#define PUSH_DUMMY_FRAME { h8300_push_dummy_frame (); }*/
/* Discard from the stack the innermost frame, restoring all registers. */
#define POP_FRAME { h8300_pop_frame (); }
#define SHORT_INT_MAX 32767
#define SHORT_INT_MIN -32768
#define REGISTER_CONVERT_TO_VIRTUAL(REGNUM,FROM,TO) \
{ memcpy((TO), (FROM), 2); }
#define REGISTER_CONVERT_TO_RAW(REGNUM,FROM,TO) \
{ memcpy((TO), (FROM), 2); }
#define BEFORE_MAIN_LOOP_HOOK \
hms_before_main_loop();
#define NAMES_HAVE_UNDERSCORE
typedef unsigned short INSN_WORD;
#define ADDR_BITS_REMOVE(addr) ((addr) & 0xffff)
#define ADDR_BITS_SET(addr) (((addr)))
#define read_memory_short(x) (read_memory_integer(x,2) & 0xffff)
#define DONT_USE_REMOTE