FreeBSD-5.3/sys/i386/conf/NOTES
#
# NOTES -- Lines that can be cut/pasted into kernel and hints configs.
#
# This file contains machine dependent kernel configuration notes. For
# machine independent notes, look in /sys/conf/NOTES.
#
# $FreeBSD: src/sys/i386/conf/NOTES,v 1.1168.2.1.2.1 2004/10/24 18:02:52 scottl Exp $
#
#
# This directive is mandatory; it defines the architecture to be
# configured for; in this case, the 386 family based IBM-PC and
# compatibles.
#
machine i386
#
# We want LINT to cover profiling as well.
profile 2
#####################################################################
# SMP OPTIONS:
#
# The apic device enables the use of the I/O APIC for interrupt delivery.
# The apic device can be used in both UP and SMP kernels, but is required
# for SMP kernels. Thus, the apic device is not strictly an SMP option,
# but it is a prerequisite for SMP.
#
# Notes:
#
# Be sure to disable 'cpu I386_CPU' for SMP kernels.
#
# By default, mixed mode is used to route IRQ0 from the AT timer via
# the 8259A master PIC through the ExtINT pin on the first I/O APIC.
# This can be disabled via the NO_MIXED_MODE option. In that case,
# IRQ0 will be routed via an intpin on the first I/O APIC. Not all
# motherboards hook IRQ0 up to the first I/O APIC even though their
# MP table or MADT may claim to do so. That is why mixed mode is
# enabled by default.
#
# HTT CPUs should only be used if they are enabled in the BIOS. For
# the ACPI case, ACPI only correctly tells us about any HTT CPUs if
# they are enabled. However, most HTT systems do not list HTT CPUs
# in the MP Table if they are enabled, thus we guess at the HTT CPUs
# for the MP Table case. However, we shouldn't try to guess and use
# these CPUs if HTT is disabled. Thus, HTT guessing is only enabled
# for the MP Table if the user explicitly asks for it via the
# MPTABLE_FORCE_HTT option. Do NOT use this option if you have HTT
# disabled in your BIOS.
#
# Mandatory:
device apic # I/O apic
# Optional:
options MPTABLE_FORCE_HTT # Enable HTT CPUs with the MP Table
options NO_MIXED_MODE # Disable use of mixed mode
#####################################################################
# CPU OPTIONS
#
# You must specify at least one CPU (the one you intend to run on);
# deleting the specification for CPUs you don't need to use may make
# parts of the system run faster.
# I386_CPU is mutually exclusive with the other CPU types.
# I386_CPU is deprecated and will be removed in 6.0-RELEASE.
#
#cpu I386_CPU
cpu I486_CPU
cpu I586_CPU # aka Pentium(tm)
cpu I686_CPU # aka Pentium Pro(tm)
#
# Options for CPU features.
#
# CPU_ATHLON_SSE_HACK tries to enable SSE instructions when the BIOS has
# forgotten to enable them.
#
# CPU_BLUELIGHTNING_3X enables triple-clock mode on IBM Blue Lightning
# CPU if CPU supports it. The default is double-clock mode on
# BlueLightning CPU box.
#
# CPU_BLUELIGHTNING_FPU_OP_CACHE enables FPU operand cache on IBM
# BlueLightning CPU. It works only with Cyrix FPU, and this option
# should not be used with Intel FPU.
#
# CPU_BTB_EN enables branch target buffer on Cyrix 5x86 (NOTE 1).
#
# CPU_CYRIX_NO_LOCK enables weak locking for the entire address space
# of Cyrix 6x86 and 6x86MX CPUs by setting the NO_LOCK bit of CCR1.
# Otherwise, the NO_LOCK bit of CCR1 is cleared. (NOTE 3)
#
# CPU_DIRECT_MAPPED_CACHE sets L1 cache of Cyrix 486DLC CPU in direct
# mapped mode. Default is 2-way set associative mode.
#
# CPU_DISABLE_5X86_LSSER disables load store serialize (i.e., enables
# reorder). This option should not be used if you use memory mapped
# I/O device(s).
#
# CPU_DISABLE_CMPXCHG disables the CMPXCHG instruction on > i386 IA32
# machines. VmWare 3.x seems to emulate this instruction poorly, causing
# the guest OS to run very slowly. This problem appears to be fixed in
# VmWare 4.x, at least in version 4.5.2, so that enabling this option with
# VmWare 4.x will result in locking operations to be 20-30 times slower.
# Enabling this with an SMP kernel will cause the kernel to be unusable.
#
# CPU_DISABLE_SSE explicitly prevents I686_CPU from turning on SSE.
#
# CPU_ELAN enables support for AMDs ElanSC520 CPU.
# CPU_ELAN_PPS enables precision timestamp code.
# CPU_ELAN_XTAL sets the clock crystal frequency in Hz.
#
# CPU_ENABLE_LONGRUN enables support for Transmeta Crusoe LongRun
# technology which allows to restrict power consumption of the CPU by
# using group of hw.crusoe.* sysctls.
#
# CPU_ENABLE_SSE enables SSE/MMX2 instructions support. This is default
# on I686_CPU and above.
#
# CPU_ENABLE_TCC enables Thermal Control Circuitry (TCC) found in some
# Pentium(tm) 4 and (possibly) later CPUs. When enabled and detected,
# TCC supports restricting power consumption using the hw.p4tcc.*
# sysctls. This operates independently of SpeedStep and is useful on
# systems where other mechanisms such as apm(4) or acpi(4) don't work.
#
# CPU_FASTER_5X86_FPU enables faster FPU exception handler.
#
# CPU_GEODE is for the SC1100 Geode embedded processor. This option
# is necessary because the i8254 timecounter is toast.
#
# CPU_I486_ON_386 enables CPU cache on i486 based CPU upgrade products
# for i386 machines.
#
# CPU_IORT defines I/O clock delay time (NOTE 1). Default values of
# I/O clock delay time on Cyrix 5x86 and 6x86 are 0 and 7,respectively
# (no clock delay).
#
# CPU_L2_LATENCY specifies the L2 cache latency value. This option is used
# only when CPU_PPRO2CELERON is defined and Mendocino Celeron is detected.
# The default value is 5.
#
# CPU_LOOP_EN prevents flushing the prefetch buffer if the destination
# of a jump is already present in the prefetch buffer on Cyrix 5x86(NOTE
# 1).
#
# CPU_PPRO2CELERON enables L2 cache of Mendocino Celeron CPUs. This option
# is useful when you use Socket 8 to Socket 370 converter, because most Pentium
# Pro BIOSs do not enable L2 cache of Mendocino Celeron CPUs.
#
# CPU_RSTK_EN enables return stack on Cyrix 5x86 (NOTE 1).
#
# CPU_SOEKRIS enables support www.soekris.com hardware.
#
# CPU_SUSP_HLT enables suspend on HALT. If this option is set, CPU
# enters suspend mode following execution of HALT instruction.
#
# CPU_UPGRADE_HW_CACHE eliminates unneeded cache flush instruction(s).
#
# CPU_WT_ALLOC enables write allocation on Cyrix 6x86/6x86MX and AMD
# K5/K6/K6-2 CPUs.
#
# CYRIX_CACHE_WORKS enables CPU cache on Cyrix 486 CPUs with cache
# flush at hold state.
#
# CYRIX_CACHE_REALLY_WORKS enables (1) CPU cache on Cyrix 486 CPUs
# without cache flush at hold state, and (2) write-back CPU cache on
# Cyrix 6x86 whose revision < 2.7 (NOTE 2).
#
# NO_F00F_HACK disables the hack that prevents Pentiums (and ONLY
# Pentiums) from locking up when a LOCK CMPXCHG8B instruction is
# executed. This option is only needed if I586_CPU is also defined,
# and should be included for any non-Pentium CPU that defines it.
#
# NO_MEMORY_HOLE is an optimisation for systems with AMD K6 processors
# which indicates that the 15-16MB range is *definitely* not being
# occupied by an ISA memory hole.
#
# NOTE 1: The options, CPU_BTB_EN, CPU_LOOP_EN, CPU_IORT,
# CPU_LOOP_EN and CPU_RSTK_EN should not be used because of CPU bugs.
# These options may crash your system.
#
# NOTE 2: If CYRIX_CACHE_REALLY_WORKS is not set, CPU cache is enabled
# in write-through mode when revision < 2.7. If revision of Cyrix
# 6x86 >= 2.7, CPU cache is always enabled in write-back mode.
#
# NOTE 3: This option may cause failures for software that requires
# locked cycles in order to operate correctly.
#
options CPU_ATHLON_SSE_HACK
options CPU_BLUELIGHTNING_3X
options CPU_BLUELIGHTNING_FPU_OP_CACHE
options CPU_BTB_EN
options CPU_DIRECT_MAPPED_CACHE
options CPU_DISABLE_5X86_LSSER
options CPU_DISABLE_CMPXCHG
#options CPU_DISABLE_SSE
options CPU_ELAN
options CPU_ELAN_PPS
options CPU_ELAN_XTAL=32768000
options CPU_ENABLE_LONGRUN
options CPU_ENABLE_SSE
options CPU_ENABLE_TCC
options CPU_FASTER_5X86_FPU
options CPU_GEODE
options CPU_I486_ON_386
options CPU_IORT
options CPU_L2_LATENCY=5
options CPU_LOOP_EN
options CPU_PPRO2CELERON
options CPU_RSTK_EN
options CPU_SOEKRIS
options CPU_SUSP_HLT
options CPU_UPGRADE_HW_CACHE
options CPU_WT_ALLOC
options CYRIX_CACHE_WORKS
options CYRIX_CACHE_REALLY_WORKS
#options NO_F00F_HACK
# Debug options
options NPX_DEBUG # enable npx debugging
#
# PERFMON causes the driver for Pentium/Pentium Pro performance counters
# to be compiled. See perfmon(4) for more information.
#
options PERFMON
#####################################################################
# NETWORKING OPTIONS
#
# DEVICE_POLLING adds support for mixed interrupt-polling handling
# of network device drivers, which has significant benefits in terms
# of robustness to overloads and responsivity, as well as permitting
# accurate scheduling of the CPU time between kernel network processing
# and other activities. The drawback is a moderate (up to 1/HZ seconds)
# potential increase in response times.
# It is strongly recommended to use HZ=1000 or 2000 with DEVICE_POLLING
# to achieve smoother behaviour.
# Additionally, you can enable/disable polling at runtime with the
# sysctl variable kern.polling.enable (defaults off), and select
# the CPU fraction reserved to userland with the sysctl variable
# kern.polling.user_frac (default 50, range 0..100).
#
# Not all device drivers support this mode of operation at the time of
# this writing. See polling(4) for more details.
options DEVICE_POLLING
#####################################################################
# CLOCK OPTIONS
# The following options are used for debugging clock behavior only, and
# should not be used for production systems.
# CLK_CALIBRATION_LOOP causes clock calibration to be run in a loop at
# startup until the user presses a key. (The i8254 clock is always
# calibrated relative to the RTC (mc146818a) and this option causes the
# calibration to be repeated.)
options CLK_CALIBRATION_LOOP
# CLK_USE_I8254_CALIBRATION causes the calibrated frequency of the i8254
# clock to actually be used.
options CLK_USE_I8254_CALIBRATION
#####################################################################
# MISCELLANEOUS DEVICES AND OPTIONS
device speaker #Play IBM BASIC-style noises out your speaker
hint.speaker.0.at="isa"
hint.speaker.0.port="0x61"
device gzip #Exec gzipped a.out's. REQUIRES COMPAT_AOUT!
device apm_saver # Requires APM
#####################################################################
# HARDWARE BUS CONFIGURATION
#
# ISA bus
#
device isa # Required by npx(4)
#
# Options for `isa':
#
# AUTO_EOI_1 enables the `automatic EOI' feature for the master 8259A
# interrupt controller. This saves about 0.7-1.25 usec for each interrupt.
# This option breaks suspend/resume on some portables.
#
# AUTO_EOI_2 enables the `automatic EOI' feature for the slave 8259A
# interrupt controller. This saves about 0.7-1.25 usec for each interrupt.
# Automatic EOI is documented not to work for for the slave with the
# original i8259A, but it works for some clones and some integrated
# versions.
#
# MAXMEM specifies the amount of RAM on the machine; if this is not
# specified, FreeBSD will first read the amount of memory from the CMOS
# RAM, so the amount of memory will initially be limited to 64MB or 16MB
# depending on the BIOS. If the BIOS reports 64MB, a memory probe will
# then attempt to detect the installed amount of RAM. If this probe
# fails to detect >64MB RAM you will have to use the MAXMEM option.
# The amount is in kilobytes, so for a machine with 128MB of RAM, it would
# be 131072 (128 * 1024).
#
# BROKEN_KEYBOARD_RESET disables the use of the keyboard controller to
# reset the CPU for reboot. This is needed on some systems with broken
# keyboard controllers.
options AUTO_EOI_1
#options AUTO_EOI_2
options MAXMEM=(128*1024)
#options BROKEN_KEYBOARD_RESET
#
# EISA bus
#
# The EISA bus device is `eisa'. It provides auto-detection and
# configuration support for all devices on the EISA bus.
device eisa
# By default, only 10 EISA slots are probed, since the slot numbers
# above clash with the configuration address space of the PCI subsystem,
# and the EISA probe is not very smart about this. This is sufficient
# for most machines, but in particular the HP NetServer LC series comes
# with an onboard AIC7770 dual-channel SCSI controller on EISA slot #11,
# thus you need to bump this figure to 12 for them.
options EISA_SLOTS=12
#
# MCA bus:
#
# The MCA bus device is `mca'. It provides auto-detection and
# configuration support for all devices on the MCA bus.
# No hints are required for MCA.
device mca
#
# PCI bus & PCI options:
#
device pci
#
# AGP GART support
device agp
options AGP_AMD64_GART # Included GART code for AMD64 machines.
#####################################################################
# HARDWARE DEVICE CONFIGURATION
# To include support for VGA VESA video modes
options VESA
# Turn on extra debugging checks and output for VESA support.
options VESA_DEBUG
# The pcvt console driver (vt220 compatible).
device vt
hint.vt.0.at="isa"
options XSERVER # support for running an X server on vt
options FAT_CURSOR # start with block cursor
# This PCVT option is for keyboards such as those used on really old ThinkPads
options PCVT_SCANSET=2
# Other PCVT options are documented in pcvt(4).
options PCVT_24LINESDEF
options PCVT_CTRL_ALT_DEL
options PCVT_META_ESC
options PCVT_NSCREENS=9
options PCVT_PRETTYSCRNS
options PCVT_SCREENSAVER
options PCVT_USEKBDSEC
options PCVT_VT220KEYB
options PCVT_GREENSAVER
#
# The Numeric Processing eXtension driver. This is non-optional.
device npx
hint.npx.0.flags="0x0"
hint.npx.0.irq="13"
#
# `flags' for npx0:
# 0x01 don't use the npx registers to optimize bcopy.
# 0x02 don't use the npx registers to optimize bzero.
# 0x04 don't use the npx registers to optimize copyin or copyout.
# The npx registers are normally used to optimize copying and zeroing when
# all of the following conditions are satisfied:
# I586_CPU is an option
# the cpu is an i586 (perhaps not a Pentium)
# the probe for npx0 succeeds
# INT 16 exception handling works.
# Then copying and zeroing using the npx registers is normally 30-100% faster.
# The flags can be used to control cases where it doesn't work or is slower.
# Setting them at boot time using userconfig works right (the optimizations
# are not used until later in the bootstrap when npx0 is attached).
# Flag 0x08 automatically disables the i586 optimized routines.
#
#
# Optional devices:
#
# 3Dfx Voodoo Graphics, Voodoo II /dev/3dfx CDEV support. This will create
# the /dev/3dfx0 device to work with glide implementations. This should get
# linked to /dev/3dfx and /dev/voodoo. Note that this is not the same as
# the tdfx DRI module from XFree86 and is completely unrelated.
#
# To enable Linuxulator support, one must also include COMPAT_LINUX in the
# config as well, or you will not have the dependencies. The other option
# is to load both as modules.
device tdfx # Enable 3Dfx Voodoo support
options TDFX_LINUX # Enable Linuxulator support
#
# ACPI support using the Intel ACPI Component Architecture reference
# implementation.
#
# ACPI_DEBUG enables the use of the debug.acpi.level and debug.acpi.layer
# kernel environment variables to select initial debugging levels for the
# Intel ACPICA code. (Note that the Intel code must also have USE_DEBUGGER
# defined when it is built).
#
# ACPI_MAX_THREADS sets the number of task threads started.
#
# ACPI_NO_SEMAPHORES makes the AcpiOs*Semaphore routines a no-op.
#
# ACPICA_PEDANTIC enables strict checking of AML. Our default is to
# relax these checks to allow code generated by the Microsoft compiler
# to still execute.
#
# Note that building ACPI into the kernel is deprecated; the module is
# normally loaded automatically by the loader.
device acpi
options ACPI_DEBUG
options ACPI_MAX_THREADS=1
#!options ACPI_NO_SEMAPHORES
#!options ACPICA_PEDANTIC
# ACPI Asus Extras (LCD backlight/brightness, video output, etc.)
device acpi_asus
# ACPI Panasonic Extras (LCD backlight/brightness, video output, etc.)
device acpi_panasonic
# ACPI Toshiba Extras (LCD backlight/brightness, video output, etc.)
device acpi_toshiba
# ACPI Video Extensions (LCD backlight/brightness, video output, etc.)
device acpi_video
# DRM options:
# mgadrm: AGP Matrox G200, G400, G450, G550
# r128drm: ATI Rage 128
# radeondrm: ATI Radeon up to 9000/9100
# sisdrm: SiS 300/305,540,630
# tdfxdrm: 3dfx Voodoo 3/4/5 and Banshee
# DRM_DEBUG: include debug printfs, very slow
#
# mga requires AGP in the kernel, and it is recommended
# for AGP r128 and radeon cards.
device mgadrm
device "r128drm"
device radeondrm
device sisdrm
device tdfxdrm
options DRM_DEBUG
#
# mse: Logitech and ATI InPort bus mouse ports
device mse
hint.mse.0.at="isa"
hint.mse.0.port="0x23c"
hint.mse.0.irq="5"
#
# Network interfaces:
#
# ar: Arnet SYNC/570i hdlc sync 2/4 port V.35/X.21 serial driver
# (requires sppp)
# arl: Aironet Arlan 655 wireless adapters.
# ath: Atheros a/b/g WiFi adapters (requires ath_hal and wlan)
# cp: Cronyx Tau-PCI sync single/dual/four port
# V.35/RS-232/RS-530/RS-449/X.21/G.703/E1/E3/T3/STS-1
# serial adaptor (requires sppp (default), or NETGRAPH if
# NETGRAPH_CRONYX is configured)
# ctau: Cronyx Tau sync dual port V.35/RS-232/RS-530/RS-449/X.21/G.703/E1
# serial adaptor (requires sppp (default), or NETGRAPH if
# NETGRAPH_CRONYX is configured)
# cx: Cronyx Sigma multiport sync/async adapter (requires sppp (default),
# or NETGRAPH if NETGRAPH_CRONYX is configured)
# ed: Western Digital and SMC 80xx; Novell NE1000 and NE2000; 3Com 3C503
# HP PC Lan+, various PC Card devices (refer to etc/defaults/pccard.conf)
# (requires miibus)
# el: 3Com 3C501 (slow!)
# ie: AT&T StarLAN 10 and EN100; 3Com 3C507; unknown NI5210;
# Intel EtherExpress
# lnc: Lance/PCnet cards (Isolan, Novell NE2100, NE32-VL, AMD Am7990 and
# Am79C960)
# oltr: Olicom ISA token-ring adapters OC-3115, OC-3117, OC-3118 and OC-3133.
# Olicom PCI token-ring adapters OC-3136, OC-3137, OC-3139, OC-3140,
# OC-3141, OC-3540 and OC-3250.
# sbni: Granch SBNI12-xx ISA and PCI adapters
# sr: RISCom/N2 hdlc sync 1/2 port V.35/X.21 serial driver (requires sppp)
# wl: Lucent Wavelan (ISA card only).
# Order for ISA/EISA devices is important here
device ar
hint.ar.0.at="isa"
hint.ar.0.port="0x300"
hint.ar.0.irq="10"
hint.ar.0.maddr="0xd0000"
device arl
hint.arl.0.at="isa"
hint.arl.0.irq="9"
hint.arl.0.maddr="0xd0000"
device cp
device ctau
hint.ctau.0.at="isa"
hint.ctau.0.port="0x240"
hint.ctau.0.irq="15"
hint.ctau.0.drq="7"
device cx
hint.cx.0.at="isa"
hint.cx.0.port="0x240"
hint.cx.0.irq="15"
hint.cx.0.drq="7"
#options NETGRAPH_CRONYX # Enable NETGRAPH support for Cronyx adapter(s)
device ed
#options ED_NO_MIIBUS # Disable ed miibus support
hint.ed.0.at="isa"
hint.ed.0.port="0x280"
hint.ed.0.irq="5"
hint.ed.0.maddr="0xd8000"
device el
hint.el.0.at="isa"
hint.el.0.port="0x300"
hint.el.0.irq="9"
device ie # Hints only required for Starlan
hint.ie.2.at="isa"
hint.ie.2.port="0x300"
hint.ie.2.irq="5"
hint.ie.2.maddr="0xd0000"
device lnc
hint.lnc.0.at="isa"
hint.lnc.0.port="0x280"
hint.lnc.0.irq="10"
hint.lnc.0.drq="0"
device sbni
hint.sbni.0.at="isa"
hint.sbni.0.port="0x210"
hint.sbni.0.irq="0xefdead"
hint.sbni.0.flags="0"
device sr
hint.sr.0.at="isa"
hint.sr.0.port="0x300"
hint.sr.0.irq="5"
hint.sr.0.maddr="0xd0000"
device oltr
hint.oltr.0.at="isa"
device wl
hint.wl.0.at="isa"
hint.wl.0.port="0x300"
options WLCACHE # enables the signal-strength cache
options WLDEBUG # enables verbose debugging output
device ath
device ath_hal # Atheros HAL (includes binary component)
#device wlan # 802.11 layer
#
# ATA raid adapters
#
device pst
#
# 3ware 9000 series PATA/SATA RAID controller driver and options.
# The driver is implemented as a SIM, and so, needs the CAM infrastructure.
#
options TWA_DEBUG # 0-10; 10 prints the most messages.
options TWA_FLASH_FIRMWARE # firmware image bundled when defined.
device twa # 3ware 9000 series PATA/SATA RAID
#
# SCSI host adapters:
#
# ncv: NCR 53C500 based SCSI host adapters.
# nsp: Workbit Ninja SCSI-3 based PC Card SCSI host adapters.
# stg: TMC 18C30, 18C50 based SCSI host adapters.
device ncv
device nsp
device stg
hint.stg.0.at="isa"
hint.stg.0.port="0x140"
hint.stg.0.port="11"
#
# Adaptec FSA RAID controllers, including integrated DELL controllers,
# the Dell PERC 2/QC and the HP NetRAID-4M
device aac
device aacp # SCSI Passthrough interface (optional, CAM required)
#
# Highpoint RocketRAID 182x. This is really just software RAID on a
# Marvell SATA chip.
device hptmv
#
# IBM (now Adaptec) ServeRAID controllers
device ips
#
# SafeNet crypto driver: can be moved to the MI NOTES as soon as
# it's tested on a big-endian machine
#
device safe # SafeNet 1141
options SAFE_DEBUG # enable debugging support: hw.safe.debug
options SAFE_RNDTEST # enable rndtest support
#####################################################################
#
# Miscellaneous hardware:
#
# apm: Laptop Advanced Power Management (experimental)
# pmtimer: Timer device driver for power management events (APM or ACPI)
# cy: Cyclades serial driver
# digi: Digiboard driver
# spic: Sony Programmable I/O controller (VAIO notebooks)
# Notes on APM
# The flags takes the following meaning for apm0:
# 0x0020 Statclock is broken.
# Notes on the Specialix SI/XIO driver:
# The host card is memory, not IO mapped.
# The Rev 1 host cards use a 64K chunk, on a 32K boundary.
# The Rev 2 host cards use a 32K chunk, on a 32K boundary.
# The cards can use an IRQ of 11, 12 or 15.
# Notes on the Sony Programmable I/O controller
# This is a temporary driver that should someday be replaced by something
# that hooks into the ACPI layer. The device is hooked to the PIIX4's
# General Device 10 decoder, which means you have to fiddle with PCI
# registers to map it in, even though it is otherwise treated here as
# an ISA device. At the moment, the driver polls, although the device
# is capable of generating interrupts. It largely undocumented.
# The port location in the hint is where you WANT the device to be
# mapped. 0x10a0 seems to be traditional. At the moment the jogdial
# is the only thing truly supported, but apparently a fair percentage
# of the Vaio extra features are controlled by this device.
device apm
hint.apm.0.flags="0x20"
device pmtimer # Adjust system timer at wakeup time
device cy
options CY_PCI_FASTINTR # Use with cy_pci unless irq is shared
hint.cy.0.at="isa"
hint.cy.0.irq="10"
hint.cy.0.maddr="0xd4000"
hint.cy.0.msize="0x2000"
device digi
hint.digi.0.at="isa"
hint.digi.0.port="0x104"
hint.digi.0.maddr="0xd0000"
# BIOS & FEP/OS components of device digi.
device digi_CX
device digi_CX_PCI
device digi_EPCX
device digi_EPCX_PCI
device digi_Xe
device digi_Xem
device digi_Xr
device spic
hint.spic.0.at="isa"
hint.spic.0.port="0x10a0"
# sx device is i386 and pc98 only at the moment.
device sx
options SX_DEBUG
# HOT1 Xilinx 6200 card (http://www.vcc.com/)
device xrpu
#
# Laptop/Notebook options:
#
# See also:
# apm under `Miscellaneous hardware'
# above.
# For older notebooks that signal a powerfail condition (external
# power supply dropped, or battery state low) by issuing an NMI:
options POWERFAIL_NMI # make it beep instead of panicing
#
# I2C Bus
#
# Philips i2c bus support is provided by the `iicbus' device.
#
# Supported interfaces:
# pcf Philips PCF8584 ISA-bus controller
#
device pcf
hint.pcf.0.at="isa"
hint.pcf.0.port="0x320"
hint.pcf.0.irq="5"
#---------------------------------------------------------------------------
# ISDN4BSD
#
# See /usr/share/examples/isdn/ROADMAP for an introduction to isdn4bsd.
#
# i4b passive ISDN cards support contains the following hardware drivers:
#
# isic - Siemens/Infineon ISDN ISAC/HSCX/IPAC chipset driver
# iwic - Winbond W6692 PCI bus ISDN S/T interface controller
# ifpi - AVM Fritz!Card PCI driver
# ifpi2 - AVM Fritz!Card PCI version 2 driver
# ihfc - Cologne Chip HFC ISA/ISA-PnP chipset driver
# ifpnp - AVM Fritz!Card PnP driver
# itjc - Siemens ISAC / TJNet Tiger300/320 chipset
#
# i4b active ISDN cards support contains the following hardware drivers:
#
# iavc - AVM B1 PCI, AVM B1 ISA, AVM T1
#
# Note that the ``options'' (if given) and ``device'' lines must BOTH
# be uncommented to enable support for a given card !
#
# In addition to a hardware driver (and probably an option) the mandatory
# ISDN protocol stack devices and the mandatory support device must be
# enabled as well as one or more devices from the optional devices section.
#
#---------------------------------------------------------------------------
# isic driver (Siemens/Infineon chipsets)
#
device isic
#
# ISA bus non-PnP Cards:
# ----------------------
#
# Teles S0/8 or Niccy 1008
options TEL_S0_8
hint.isic.0.at="isa"
hint.isic.0.maddr="0xd0000"
hint.isic.0.irq="5"
hint.isic.0.flags="1"
#
# Teles S0/16 or Creatix ISDN-S0 or Niccy 1016
options TEL_S0_16
hint.isic.0.at="isa"
hint.isic.0.port="0xd80"
hint.isic.0.maddr="0xd0000"
hint.isic.0.irq="5"
hint.isic.0.flags="2"
#
# Teles S0/16.3
options TEL_S0_16_3
hint.isic.0.at="isa"
hint.isic.0.port="0xd80"
hint.isic.0.irq="5"
hint.isic.0.flags="3"
#
# AVM A1 or AVM Fritz!Card
options AVM_A1
hint.isic.0.at="isa"
hint.isic.0.port="0x340"
hint.isic.0.irq="5"
hint.isic.0.flags="4"
#
# USRobotics Sportster ISDN TA intern
options USR_STI
hint.isic.0.at="isa"
hint.isic.0.port="0x268"
hint.isic.0.irq="5"
hint.isic.0.flags="7"
#
# ITK ix1 Micro ( < V.3, non-PnP version )
options ITKIX1
hint.isic.0.at="isa"
hint.isic.0.port="0x398"
hint.isic.0.irq="10"
hint.isic.0.flags="18"
#
# ELSA PCC-16
options ELSA_PCC16
hint.isic.0.at="isa"
hint.isic.0.port="0x360"
hint.isic.0.irq="10"
hint.isic.0.flags="20"
#
# ISA bus PnP Cards:
# ------------------
#
# Teles S0/16.3 PnP
options TEL_S0_16_3_P
#
# Creatix ISDN-S0 P&P
options CRTX_S0_P
#
# Dr. Neuhaus Niccy Go@
options DRN_NGO
#
# Sedlbauer Win Speed
options SEDLBAUER
#
# Dynalink IS64PH
options DYNALINK
#
# ELSA QuickStep 1000pro ISA
options ELSA_QS1ISA
#
# Siemens I-Surf 2.0
options SIEMENS_ISURF2
#
# Asuscom ISDNlink 128K ISA
options ASUSCOM_IPAC
#
# Eicon Diehl DIVA 2.0 and 2.02
options EICON_DIVA
#
# Compaq Microcom 610 ISDN card (Compaq series PSB2222I)
options COMPAQ_M610
#
# PCI bus Cards:
# --------------
#
# ELSA MicroLink ISDN/PCI (same as ELSA QuickStep 1000pro PCI)
options ELSA_QS1PCI
#
#---------------------------------------------------------------------------
# ifpnp driver for AVM Fritz!Card PnP
#
# AVM Fritz!Card PnP
device ifpnp
#
#---------------------------------------------------------------------------
# ihfc driver for Cologne Chip ISA chipsets (experimental!)
#
# Teles 16.3c ISA PnP
# AcerISDN P10 ISA PnP
# TELEINT ISDN SPEED No.1
device ihfc
#
#---------------------------------------------------------------------------
# ifpi driver for AVM Fritz!Card PCI
#
# AVM Fritz!Card PCI
device ifpi
#
#---------------------------------------------------------------------------
# ifpi2 driver for AVM Fritz!Card PCI version 2
#
# AVM Fritz!Card PCI version 2
device "ifpi2"
#
#---------------------------------------------------------------------------
# iwic driver for Winbond W6692 chipset
#
# ASUSCOM P-IN100-ST-D (and other Winbond W6692 based cards)
device iwic
#
#---------------------------------------------------------------------------
# itjc driver for Siemens ISAC / TJNet Tiger300/320 chipset
#
# Traverse Technologies NETjet-S
# Teles PCI-TJ
device itjc
#
#---------------------------------------------------------------------------
# iavc driver (AVM active cards, needs i4bcapi driver!)
#
device iavc
#
# AVM B1 ISA bus (PnP mode not supported!)
# ----------------------------------------
hint.iavc.0.at="isa"
hint.iavc.0.port="0x150"
hint.iavc.0.irq="5"
#
#---------------------------------------------------------------------------
# ISDN Protocol Stack - mandatory for all hardware drivers
#
# Q.921 / layer 2 - i4b passive cards D channel handling
device "i4bq921"
#
# Q.931 / layer 3 - i4b passive cards D channel handling
device "i4bq931"
#
# layer 4 - i4b common passive and active card handling
device "i4b"
#
#---------------------------------------------------------------------------
# ISDN devices - mandatory for all hardware drivers
#
# userland driver to do ISDN tracing (for passive cards only)
device "i4btrc" 4
#
# userland driver to control the whole thing
device "i4bctl"
#
#---------------------------------------------------------------------------
# ISDN devices - optional
#
# userland driver for access to raw B channel
device "i4brbch" 4
#
# userland driver for telephony
device "i4btel" 2
#
# network driver for IP over raw HDLC ISDN
device "i4bipr" 4
# enable VJ header compression detection for ipr i/f
options IPR_VJ
# enable logging of the first n IP packets to isdnd (n=32 here)
options IPR_LOG=32
#
# network driver for sync PPP over ISDN; requires an equivalent
# number of sppp device to be configured
device "i4bisppp" 4
#
# B-channel interface to the netgraph subsystem
device "i4bing" 2
#
# CAPI driver needed for active ISDN cards (see iavc driver above)
device "i4bcapi"
#
#---------------------------------------------------------------------------
#
# System Management Bus (SMB)
#
options ENABLE_ALART # Control alarm on Intel intpm driver
#
# Set the number of PV entries per process. Increasing this can
# stop panics related to heavy use of shared memory. However, that can
# (combined with large amounts of physical memory) cause panics at
# boot time due the kernel running out of VM space.
#
# If you're tweaking this, you might also want to increase the sysctls
# "vm.v_free_min", "vm.v_free_reserved", and "vm.v_free_target".
#
# The value below is the one more than the default.
#
options PMAP_SHPGPERPROC=201
#
# Change the size of the kernel virtual address space. Due to
# constraints in loader(8) on i386, this must be a multiple of 4.
# 256 = 1 GB of kernel address space. Increasing this also causes
# a reduction of the address space in user processes. 512 splits
# the 4GB cpu address space in half (2GB user, 2GB kernel).
#
options KVA_PAGES=260
#####################################################################
# ABI Emulation
# Enable iBCS2 runtime support for SCO and ISC binaries
options IBCS2
# Emulate spx device for client side of SVR3 local X interface
options SPX_HACK
# Enable Linux ABI emulation
options COMPAT_LINUX
# Enable i386 a.out binary support
options COMPAT_AOUT
# Enable the linux-like proc filesystem support (requires COMPAT_LINUX
# and PSEUDOFS)
options LINPROCFS
#
# SysVR4 ABI emulation
#
# The svr4 ABI emulator can be statically compiled into the kernel or loaded as
# a KLD module.
# The STREAMS network emulation code can also be compiled statically or as a
# module. If loaded as a module, it must be loaded before the svr4 module
# (the /usr/sbin/svr4 script does this for you). If compiling statically,
# the `streams' device must be configured into any kernel which also
# specifies COMPAT_SVR4. It is possible to have a statically-configured
# STREAMS device and a dynamically loadable svr4 emulator; the /usr/sbin/svr4
# script understands that it doesn't need to load the `streams' module under
# those circumstances.
# Caveat: At this time, `options KTRACE' is required for the svr4 emulator
# (whether static or dynamic).
#
options COMPAT_SVR4 # build emulator statically
options DEBUG_SVR4 # enable verbose debugging
device streams # STREAMS network driver (required for svr4).
#####################################################################
# VM OPTIONS
# Disable the 4 MByte page PSE CPU feature. The PSE feature allows the
# kernel to use 4 MByte pages to map the kernel instead of 4k pages.
# This saves on the amount of memory needed for page tables needed to
# map the kernel. You should only disable this feature as a temporary
# workaround if you are having problems with it enabled.
#
#options DISABLE_PSE
# Disable the global pages PGE CPU feature. The PGE feature allows pages
# to be marked with the PG_G bit. TLB entries for these pages are not
# flushed from the cache when %cr3 is reloaded. This can make context
# switches less expensive. You should only disable this feature as a
# temporary workaround if you are having problems with it enabled.
#
#options DISABLE_PG_G
# KSTACK_PAGES is the number of memory pages to assign to the kernel
# stack of each thread.
options KSTACK_PAGES=3
#####################################################################
# More undocumented options for linting.
# Note that documenting these are not considered an affront.
options FB_INSTALL_CDEV # install a CDEV entry in /dev
# PECOFF module (Win32 Execution Format)
options PECOFF_SUPPORT
options PECOFF_DEBUG
options I4B_SMP_WORKAROUND
options I586_PMC_GUPROF=0x70000
options KBDIO_DEBUG=2
options KBD_MAXRETRY=4
options KBD_MAXWAIT=6
options KBD_RESETDELAY=201
options PSM_DEBUG=1
options TIMER_FREQ=((14318182+6)/12)
options VM_KMEM_SIZE
options VM_KMEM_SIZE_MAX
options VM_KMEM_SIZE_SCALE
# The I/O device
device io