Linux-2.6.33.2/arch/blackfin/mach-bf548/include/mach/defBF542.h
/*
* Copyright 2007-2008 Analog Devices Inc.
*
* Licensed under the ADI BSD license or the GPL-2 (or later)
*/
#ifndef _DEF_BF542_H
#define _DEF_BF542_H
/* Include all Core registers and bit definitions */
#include <asm/def_LPBlackfin.h>
/* SYSTEM & MMR ADDRESS DEFINITIONS FOR ADSP-BF542 */
/* Include defBF54x_base.h for the set of #defines that are common to all ADSP-BF54x processors */
#include "defBF54x_base.h"
/* The following are the #defines needed by ADSP-BF542 that are not in the common header */
/* ATAPI Registers */
#define ATAPI_CONTROL 0xffc03800 /* ATAPI Control Register */
#define ATAPI_STATUS 0xffc03804 /* ATAPI Status Register */
#define ATAPI_DEV_ADDR 0xffc03808 /* ATAPI Device Register Address */
#define ATAPI_DEV_TXBUF 0xffc0380c /* ATAPI Device Register Write Data */
#define ATAPI_DEV_RXBUF 0xffc03810 /* ATAPI Device Register Read Data */
#define ATAPI_INT_MASK 0xffc03814 /* ATAPI Interrupt Mask Register */
#define ATAPI_INT_STATUS 0xffc03818 /* ATAPI Interrupt Status Register */
#define ATAPI_XFER_LEN 0xffc0381c /* ATAPI Length of Transfer */
#define ATAPI_LINE_STATUS 0xffc03820 /* ATAPI Line Status */
#define ATAPI_SM_STATE 0xffc03824 /* ATAPI State Machine Status */
#define ATAPI_TERMINATE 0xffc03828 /* ATAPI Host Terminate */
#define ATAPI_PIO_TFRCNT 0xffc0382c /* ATAPI PIO mode transfer count */
#define ATAPI_DMA_TFRCNT 0xffc03830 /* ATAPI DMA mode transfer count */
#define ATAPI_UMAIN_TFRCNT 0xffc03834 /* ATAPI UDMAIN transfer count */
#define ATAPI_UDMAOUT_TFRCNT 0xffc03838 /* ATAPI UDMAOUT transfer count */
#define ATAPI_REG_TIM_0 0xffc03840 /* ATAPI Register Transfer Timing 0 */
#define ATAPI_PIO_TIM_0 0xffc03844 /* ATAPI PIO Timing 0 Register */
#define ATAPI_PIO_TIM_1 0xffc03848 /* ATAPI PIO Timing 1 Register */
#define ATAPI_MULTI_TIM_0 0xffc03850 /* ATAPI Multi-DMA Timing 0 Register */
#define ATAPI_MULTI_TIM_1 0xffc03854 /* ATAPI Multi-DMA Timing 1 Register */
#define ATAPI_MULTI_TIM_2 0xffc03858 /* ATAPI Multi-DMA Timing 2 Register */
#define ATAPI_ULTRA_TIM_0 0xffc03860 /* ATAPI Ultra-DMA Timing 0 Register */
#define ATAPI_ULTRA_TIM_1 0xffc03864 /* ATAPI Ultra-DMA Timing 1 Register */
#define ATAPI_ULTRA_TIM_2 0xffc03868 /* ATAPI Ultra-DMA Timing 2 Register */
#define ATAPI_ULTRA_TIM_3 0xffc0386c /* ATAPI Ultra-DMA Timing 3 Register */
/* SDH Registers */
#define SDH_PWR_CTL 0xffc03900 /* SDH Power Control */
#define SDH_CLK_CTL 0xffc03904 /* SDH Clock Control */
#define SDH_ARGUMENT 0xffc03908 /* SDH Argument */
#define SDH_COMMAND 0xffc0390c /* SDH Command */
#define SDH_RESP_CMD 0xffc03910 /* SDH Response Command */
#define SDH_RESPONSE0 0xffc03914 /* SDH Response0 */
#define SDH_RESPONSE1 0xffc03918 /* SDH Response1 */
#define SDH_RESPONSE2 0xffc0391c /* SDH Response2 */
#define SDH_RESPONSE3 0xffc03920 /* SDH Response3 */
#define SDH_DATA_TIMER 0xffc03924 /* SDH Data Timer */
#define SDH_DATA_LGTH 0xffc03928 /* SDH Data Length */
#define SDH_DATA_CTL 0xffc0392c /* SDH Data Control */
#define SDH_DATA_CNT 0xffc03930 /* SDH Data Counter */
#define SDH_STATUS 0xffc03934 /* SDH Status */
#define SDH_STATUS_CLR 0xffc03938 /* SDH Status Clear */
#define SDH_MASK0 0xffc0393c /* SDH Interrupt0 Mask */
#define SDH_MASK1 0xffc03940 /* SDH Interrupt1 Mask */
#define SDH_FIFO_CNT 0xffc03948 /* SDH FIFO Counter */
#define SDH_FIFO 0xffc03980 /* SDH Data FIFO */
#define SDH_E_STATUS 0xffc039c0 /* SDH Exception Status */
#define SDH_E_MASK 0xffc039c4 /* SDH Exception Mask */
#define SDH_CFG 0xffc039c8 /* SDH Configuration */
#define SDH_RD_WAIT_EN 0xffc039cc /* SDH Read Wait Enable */
#define SDH_PID0 0xffc039d0 /* SDH Peripheral Identification0 */
#define SDH_PID1 0xffc039d4 /* SDH Peripheral Identification1 */
#define SDH_PID2 0xffc039d8 /* SDH Peripheral Identification2 */
#define SDH_PID3 0xffc039dc /* SDH Peripheral Identification3 */
#define SDH_PID4 0xffc039e0 /* SDH Peripheral Identification4 */
#define SDH_PID5 0xffc039e4 /* SDH Peripheral Identification5 */
#define SDH_PID6 0xffc039e8 /* SDH Peripheral Identification6 */
#define SDH_PID7 0xffc039ec /* SDH Peripheral Identification7 */
/* USB Control Registers */
#define USB_FADDR 0xffc03c00 /* Function address register */
#define USB_POWER 0xffc03c04 /* Power management register */
#define USB_INTRTX 0xffc03c08 /* Interrupt register for endpoint 0 and Tx endpoint 1 to 7 */
#define USB_INTRRX 0xffc03c0c /* Interrupt register for Rx endpoints 1 to 7 */
#define USB_INTRTXE 0xffc03c10 /* Interrupt enable register for IntrTx */
#define USB_INTRRXE 0xffc03c14 /* Interrupt enable register for IntrRx */
#define USB_INTRUSB 0xffc03c18 /* Interrupt register for common USB interrupts */
#define USB_INTRUSBE 0xffc03c1c /* Interrupt enable register for IntrUSB */
#define USB_FRAME 0xffc03c20 /* USB frame number */
#define USB_INDEX 0xffc03c24 /* Index register for selecting the indexed endpoint registers */
#define USB_TESTMODE 0xffc03c28 /* Enabled USB 20 test modes */
#define USB_GLOBINTR 0xffc03c2c /* Global Interrupt Mask register and Wakeup Exception Interrupt */
#define USB_GLOBAL_CTL 0xffc03c30 /* Global Clock Control for the core */
/* USB Packet Control Registers */
#define USB_TX_MAX_PACKET 0xffc03c40 /* Maximum packet size for Host Tx endpoint */
#define USB_CSR0 0xffc03c44 /* Control Status register for endpoint 0 and Control Status register for Host Tx endpoint */
#define USB_TXCSR 0xffc03c44 /* Control Status register for endpoint 0 and Control Status register for Host Tx endpoint */
#define USB_RX_MAX_PACKET 0xffc03c48 /* Maximum packet size for Host Rx endpoint */
#define USB_RXCSR 0xffc03c4c /* Control Status register for Host Rx endpoint */
#define USB_COUNT0 0xffc03c50 /* Number of bytes received in endpoint 0 FIFO and Number of bytes received in Host Tx endpoint */
#define USB_RXCOUNT 0xffc03c50 /* Number of bytes received in endpoint 0 FIFO and Number of bytes received in Host Tx endpoint */
#define USB_TXTYPE 0xffc03c54 /* Sets the transaction protocol and peripheral endpoint number for the Host Tx endpoint */
#define USB_NAKLIMIT0 0xffc03c58 /* Sets the NAK response timeout on Endpoint 0 and on Bulk transfers for Host Tx endpoint */
#define USB_TXINTERVAL 0xffc03c58 /* Sets the NAK response timeout on Endpoint 0 and on Bulk transfers for Host Tx endpoint */
#define USB_RXTYPE 0xffc03c5c /* Sets the transaction protocol and peripheral endpoint number for the Host Rx endpoint */
#define USB_RXINTERVAL 0xffc03c60 /* Sets the polling interval for Interrupt and Isochronous transfers or the NAK response timeout on Bulk transfers */
#define USB_TXCOUNT 0xffc03c68 /* Number of bytes to be written to the selected endpoint Tx FIFO */
/* USB Endpoint FIFO Registers */
#define USB_EP0_FIFO 0xffc03c80 /* Endpoint 0 FIFO */
#define USB_EP1_FIFO 0xffc03c88 /* Endpoint 1 FIFO */
#define USB_EP2_FIFO 0xffc03c90 /* Endpoint 2 FIFO */
#define USB_EP3_FIFO 0xffc03c98 /* Endpoint 3 FIFO */
#define USB_EP4_FIFO 0xffc03ca0 /* Endpoint 4 FIFO */
#define USB_EP5_FIFO 0xffc03ca8 /* Endpoint 5 FIFO */
#define USB_EP6_FIFO 0xffc03cb0 /* Endpoint 6 FIFO */
#define USB_EP7_FIFO 0xffc03cb8 /* Endpoint 7 FIFO */
/* USB OTG Control Registers */
#define USB_OTG_DEV_CTL 0xffc03d00 /* OTG Device Control Register */
#define USB_OTG_VBUS_IRQ 0xffc03d04 /* OTG VBUS Control Interrupts */
#define USB_OTG_VBUS_MASK 0xffc03d08 /* VBUS Control Interrupt Enable */
/* USB Phy Control Registers */
#define USB_LINKINFO 0xffc03d48 /* Enables programming of some PHY-side delays */
#define USB_VPLEN 0xffc03d4c /* Determines duration of VBUS pulse for VBUS charging */
#define USB_HS_EOF1 0xffc03d50 /* Time buffer for High-Speed transactions */
#define USB_FS_EOF1 0xffc03d54 /* Time buffer for Full-Speed transactions */
#define USB_LS_EOF1 0xffc03d58 /* Time buffer for Low-Speed transactions */
/* (APHY_CNTRL is for ADI usage only) */
#define USB_APHY_CNTRL 0xffc03de0 /* Register that increases visibility of Analog PHY */
/* (APHY_CALIB is for ADI usage only) */
#define USB_APHY_CALIB 0xffc03de4 /* Register used to set some calibration values */
#define USB_APHY_CNTRL2 0xffc03de8 /* Register used to prevent re-enumeration once Moab goes into hibernate mode */
/* (PHY_TEST is for ADI usage only) */
#define USB_PHY_TEST 0xffc03dec /* Used for reducing simulation time and simplifies FIFO testability */
#define USB_PLLOSC_CTRL 0xffc03df0 /* Used to program different parameters for USB PLL and Oscillator */
#define USB_SRP_CLKDIV 0xffc03df4 /* Used to program clock divide value for the clock fed to the SRP detection logic */
/* USB Endpoint 0 Control Registers */
#define USB_EP_NI0_TXMAXP 0xffc03e00 /* Maximum packet size for Host Tx endpoint0 */
#define USB_EP_NI0_TXCSR 0xffc03e04 /* Control Status register for endpoint 0 */
#define USB_EP_NI0_RXMAXP 0xffc03e08 /* Maximum packet size for Host Rx endpoint0 */
#define USB_EP_NI0_RXCSR 0xffc03e0c /* Control Status register for Host Rx endpoint0 */
#define USB_EP_NI0_RXCOUNT 0xffc03e10 /* Number of bytes received in endpoint 0 FIFO */
#define USB_EP_NI0_TXTYPE 0xffc03e14 /* Sets the transaction protocol and peripheral endpoint number for the Host Tx endpoint0 */
#define USB_EP_NI0_TXINTERVAL 0xffc03e18 /* Sets the NAK response timeout on Endpoint 0 */
#define USB_EP_NI0_RXTYPE 0xffc03e1c /* Sets the transaction protocol and peripheral endpoint number for the Host Rx endpoint0 */
#define USB_EP_NI0_RXINTERVAL 0xffc03e20 /* Sets the polling interval for Interrupt/Isochronous transfers or the NAK response timeout on Bulk transfers for Host Rx endpoint0 */
/* USB Endpoint 1 Control Registers */
#define USB_EP_NI0_TXCOUNT 0xffc03e28 /* Number of bytes to be written to the endpoint0 Tx FIFO */
#define USB_EP_NI1_TXMAXP 0xffc03e40 /* Maximum packet size for Host Tx endpoint1 */
#define USB_EP_NI1_TXCSR 0xffc03e44 /* Control Status register for endpoint1 */
#define USB_EP_NI1_RXMAXP 0xffc03e48 /* Maximum packet size for Host Rx endpoint1 */
#define USB_EP_NI1_RXCSR 0xffc03e4c /* Control Status register for Host Rx endpoint1 */
#define USB_EP_NI1_RXCOUNT 0xffc03e50 /* Number of bytes received in endpoint1 FIFO */
#define USB_EP_NI1_TXTYPE 0xffc03e54 /* Sets the transaction protocol and peripheral endpoint number for the Host Tx endpoint1 */
#define USB_EP_NI1_TXINTERVAL 0xffc03e58 /* Sets the NAK response timeout on Endpoint1 */
#define USB_EP_NI1_RXTYPE 0xffc03e5c /* Sets the transaction protocol and peripheral endpoint number for the Host Rx endpoint1 */
#define USB_EP_NI1_RXINTERVAL 0xffc03e60 /* Sets the polling interval for Interrupt/Isochronous transfers or the NAK response timeout on Bulk transfers for Host Rx endpoint1 */
/* USB Endpoint 2 Control Registers */
#define USB_EP_NI1_TXCOUNT 0xffc03e68 /* Number of bytes to be written to the+H102 endpoint1 Tx FIFO */
#define USB_EP_NI2_TXMAXP 0xffc03e80 /* Maximum packet size for Host Tx endpoint2 */
#define USB_EP_NI2_TXCSR 0xffc03e84 /* Control Status register for endpoint2 */
#define USB_EP_NI2_RXMAXP 0xffc03e88 /* Maximum packet size for Host Rx endpoint2 */
#define USB_EP_NI2_RXCSR 0xffc03e8c /* Control Status register for Host Rx endpoint2 */
#define USB_EP_NI2_RXCOUNT 0xffc03e90 /* Number of bytes received in endpoint2 FIFO */
#define USB_EP_NI2_TXTYPE 0xffc03e94 /* Sets the transaction protocol and peripheral endpoint number for the Host Tx endpoint2 */
#define USB_EP_NI2_TXINTERVAL 0xffc03e98 /* Sets the NAK response timeout on Endpoint2 */
#define USB_EP_NI2_RXTYPE 0xffc03e9c /* Sets the transaction protocol and peripheral endpoint number for the Host Rx endpoint2 */
#define USB_EP_NI2_RXINTERVAL 0xffc03ea0 /* Sets the polling interval for Interrupt/Isochronous transfers or the NAK response timeout on Bulk transfers for Host Rx endpoint2 */
/* USB Endpoint 3 Control Registers */
#define USB_EP_NI2_TXCOUNT 0xffc03ea8 /* Number of bytes to be written to the endpoint2 Tx FIFO */
#define USB_EP_NI3_TXMAXP 0xffc03ec0 /* Maximum packet size for Host Tx endpoint3 */
#define USB_EP_NI3_TXCSR 0xffc03ec4 /* Control Status register for endpoint3 */
#define USB_EP_NI3_RXMAXP 0xffc03ec8 /* Maximum packet size for Host Rx endpoint3 */
#define USB_EP_NI3_RXCSR 0xffc03ecc /* Control Status register for Host Rx endpoint3 */
#define USB_EP_NI3_RXCOUNT 0xffc03ed0 /* Number of bytes received in endpoint3 FIFO */
#define USB_EP_NI3_TXTYPE 0xffc03ed4 /* Sets the transaction protocol and peripheral endpoint number for the Host Tx endpoint3 */
#define USB_EP_NI3_TXINTERVAL 0xffc03ed8 /* Sets the NAK response timeout on Endpoint3 */
#define USB_EP_NI3_RXTYPE 0xffc03edc /* Sets the transaction protocol and peripheral endpoint number for the Host Rx endpoint3 */
#define USB_EP_NI3_RXINTERVAL 0xffc03ee0 /* Sets the polling interval for Interrupt/Isochronous transfers or the NAK response timeout on Bulk transfers for Host Rx endpoint3 */
/* USB Endpoint 4 Control Registers */
#define USB_EP_NI3_TXCOUNT 0xffc03ee8 /* Number of bytes to be written to the H124endpoint3 Tx FIFO */
#define USB_EP_NI4_TXMAXP 0xffc03f00 /* Maximum packet size for Host Tx endpoint4 */
#define USB_EP_NI4_TXCSR 0xffc03f04 /* Control Status register for endpoint4 */
#define USB_EP_NI4_RXMAXP 0xffc03f08 /* Maximum packet size for Host Rx endpoint4 */
#define USB_EP_NI4_RXCSR 0xffc03f0c /* Control Status register for Host Rx endpoint4 */
#define USB_EP_NI4_RXCOUNT 0xffc03f10 /* Number of bytes received in endpoint4 FIFO */
#define USB_EP_NI4_TXTYPE 0xffc03f14 /* Sets the transaction protocol and peripheral endpoint number for the Host Tx endpoint4 */
#define USB_EP_NI4_TXINTERVAL 0xffc03f18 /* Sets the NAK response timeout on Endpoint4 */
#define USB_EP_NI4_RXTYPE 0xffc03f1c /* Sets the transaction protocol and peripheral endpoint number for the Host Rx endpoint4 */
#define USB_EP_NI4_RXINTERVAL 0xffc03f20 /* Sets the polling interval for Interrupt/Isochronous transfers or the NAK response timeout on Bulk transfers for Host Rx endpoint4 */
/* USB Endpoint 5 Control Registers */
#define USB_EP_NI4_TXCOUNT 0xffc03f28 /* Number of bytes to be written to the endpoint4 Tx FIFO */
#define USB_EP_NI5_TXMAXP 0xffc03f40 /* Maximum packet size for Host Tx endpoint5 */
#define USB_EP_NI5_TXCSR 0xffc03f44 /* Control Status register for endpoint5 */
#define USB_EP_NI5_RXMAXP 0xffc03f48 /* Maximum packet size for Host Rx endpoint5 */
#define USB_EP_NI5_RXCSR 0xffc03f4c /* Control Status register for Host Rx endpoint5 */
#define USB_EP_NI5_RXCOUNT 0xffc03f50 /* Number of bytes received in endpoint5 FIFO */
#define USB_EP_NI5_TXTYPE 0xffc03f54 /* Sets the transaction protocol and peripheral endpoint number for the Host Tx endpoint5 */
#define USB_EP_NI5_TXINTERVAL 0xffc03f58 /* Sets the NAK response timeout on Endpoint5 */
#define USB_EP_NI5_RXTYPE 0xffc03f5c /* Sets the transaction protocol and peripheral endpoint number for the Host Rx endpoint5 */
#define USB_EP_NI5_RXINTERVAL 0xffc03f60 /* Sets the polling interval for Interrupt/Isochronous transfers or the NAK response timeout on Bulk transfers for Host Rx endpoint5 */
/* USB Endpoint 6 Control Registers */
#define USB_EP_NI5_TXCOUNT 0xffc03f68 /* Number of bytes to be written to the H145endpoint5 Tx FIFO */
#define USB_EP_NI6_TXMAXP 0xffc03f80 /* Maximum packet size for Host Tx endpoint6 */
#define USB_EP_NI6_TXCSR 0xffc03f84 /* Control Status register for endpoint6 */
#define USB_EP_NI6_RXMAXP 0xffc03f88 /* Maximum packet size for Host Rx endpoint6 */
#define USB_EP_NI6_RXCSR 0xffc03f8c /* Control Status register for Host Rx endpoint6 */
#define USB_EP_NI6_RXCOUNT 0xffc03f90 /* Number of bytes received in endpoint6 FIFO */
#define USB_EP_NI6_TXTYPE 0xffc03f94 /* Sets the transaction protocol and peripheral endpoint number for the Host Tx endpoint6 */
#define USB_EP_NI6_TXINTERVAL 0xffc03f98 /* Sets the NAK response timeout on Endpoint6 */
#define USB_EP_NI6_RXTYPE 0xffc03f9c /* Sets the transaction protocol and peripheral endpoint number for the Host Rx endpoint6 */
#define USB_EP_NI6_RXINTERVAL 0xffc03fa0 /* Sets the polling interval for Interrupt/Isochronous transfers or the NAK response timeout on Bulk transfers for Host Rx endpoint6 */
/* USB Endpoint 7 Control Registers */
#define USB_EP_NI6_TXCOUNT 0xffc03fa8 /* Number of bytes to be written to the endpoint6 Tx FIFO */
#define USB_EP_NI7_TXMAXP 0xffc03fc0 /* Maximum packet size for Host Tx endpoint7 */
#define USB_EP_NI7_TXCSR 0xffc03fc4 /* Control Status register for endpoint7 */
#define USB_EP_NI7_RXMAXP 0xffc03fc8 /* Maximum packet size for Host Rx endpoint7 */
#define USB_EP_NI7_RXCSR 0xffc03fcc /* Control Status register for Host Rx endpoint7 */
#define USB_EP_NI7_RXCOUNT 0xffc03fd0 /* Number of bytes received in endpoint7 FIFO */
#define USB_EP_NI7_TXTYPE 0xffc03fd4 /* Sets the transaction protocol and peripheral endpoint number for the Host Tx endpoint7 */
#define USB_EP_NI7_TXINTERVAL 0xffc03fd8 /* Sets the NAK response timeout on Endpoint7 */
#define USB_EP_NI7_RXTYPE 0xffc03fdc /* Sets the transaction protocol and peripheral endpoint number for the Host Rx endpoint7 */
#define USB_EP_NI7_RXINTERVAL 0xffc03ff0 /* Sets the polling interval for Interrupt/Isochronous transfers or the NAK response timeout on Bulk transfers for Host Rx endpoint7 */
#define USB_EP_NI7_TXCOUNT 0xffc03ff8 /* Number of bytes to be written to the endpoint7 Tx FIFO */
#define USB_DMA_INTERRUPT 0xffc04000 /* Indicates pending interrupts for the DMA channels */
/* USB Channel 0 Config Registers */
#define USB_DMA0CONTROL 0xffc04004 /* DMA master channel 0 configuration */
#define USB_DMA0ADDRLOW 0xffc04008 /* Lower 16-bits of memory source/destination address for DMA master channel 0 */
#define USB_DMA0ADDRHIGH 0xffc0400c /* Upper 16-bits of memory source/destination address for DMA master channel 0 */
#define USB_DMA0COUNTLOW 0xffc04010 /* Lower 16-bits of byte count of DMA transfer for DMA master channel 0 */
#define USB_DMA0COUNTHIGH 0xffc04014 /* Upper 16-bits of byte count of DMA transfer for DMA master channel 0 */
/* USB Channel 1 Config Registers */
#define USB_DMA1CONTROL 0xffc04024 /* DMA master channel 1 configuration */
#define USB_DMA1ADDRLOW 0xffc04028 /* Lower 16-bits of memory source/destination address for DMA master channel 1 */
#define USB_DMA1ADDRHIGH 0xffc0402c /* Upper 16-bits of memory source/destination address for DMA master channel 1 */
#define USB_DMA1COUNTLOW 0xffc04030 /* Lower 16-bits of byte count of DMA transfer for DMA master channel 1 */
#define USB_DMA1COUNTHIGH 0xffc04034 /* Upper 16-bits of byte count of DMA transfer for DMA master channel 1 */
/* USB Channel 2 Config Registers */
#define USB_DMA2CONTROL 0xffc04044 /* DMA master channel 2 configuration */
#define USB_DMA2ADDRLOW 0xffc04048 /* Lower 16-bits of memory source/destination address for DMA master channel 2 */
#define USB_DMA2ADDRHIGH 0xffc0404c /* Upper 16-bits of memory source/destination address for DMA master channel 2 */
#define USB_DMA2COUNTLOW 0xffc04050 /* Lower 16-bits of byte count of DMA transfer for DMA master channel 2 */
#define USB_DMA2COUNTHIGH 0xffc04054 /* Upper 16-bits of byte count of DMA transfer for DMA master channel 2 */
/* USB Channel 3 Config Registers */
#define USB_DMA3CONTROL 0xffc04064 /* DMA master channel 3 configuration */
#define USB_DMA3ADDRLOW 0xffc04068 /* Lower 16-bits of memory source/destination address for DMA master channel 3 */
#define USB_DMA3ADDRHIGH 0xffc0406c /* Upper 16-bits of memory source/destination address for DMA master channel 3 */
#define USB_DMA3COUNTLOW 0xffc04070 /* Lower 16-bits of byte count of DMA transfer for DMA master channel 3 */
#define USB_DMA3COUNTHIGH 0xffc04074 /* Upper 16-bits of byte count of DMA transfer for DMA master channel 3 */
/* USB Channel 4 Config Registers */
#define USB_DMA4CONTROL 0xffc04084 /* DMA master channel 4 configuration */
#define USB_DMA4ADDRLOW 0xffc04088 /* Lower 16-bits of memory source/destination address for DMA master channel 4 */
#define USB_DMA4ADDRHIGH 0xffc0408c /* Upper 16-bits of memory source/destination address for DMA master channel 4 */
#define USB_DMA4COUNTLOW 0xffc04090 /* Lower 16-bits of byte count of DMA transfer for DMA master channel 4 */
#define USB_DMA4COUNTHIGH 0xffc04094 /* Upper 16-bits of byte count of DMA transfer for DMA master channel 4 */
/* USB Channel 5 Config Registers */
#define USB_DMA5CONTROL 0xffc040a4 /* DMA master channel 5 configuration */
#define USB_DMA5ADDRLOW 0xffc040a8 /* Lower 16-bits of memory source/destination address for DMA master channel 5 */
#define USB_DMA5ADDRHIGH 0xffc040ac /* Upper 16-bits of memory source/destination address for DMA master channel 5 */
#define USB_DMA5COUNTLOW 0xffc040b0 /* Lower 16-bits of byte count of DMA transfer for DMA master channel 5 */
#define USB_DMA5COUNTHIGH 0xffc040b4 /* Upper 16-bits of byte count of DMA transfer for DMA master channel 5 */
/* USB Channel 6 Config Registers */
#define USB_DMA6CONTROL 0xffc040c4 /* DMA master channel 6 configuration */
#define USB_DMA6ADDRLOW 0xffc040c8 /* Lower 16-bits of memory source/destination address for DMA master channel 6 */
#define USB_DMA6ADDRHIGH 0xffc040cc /* Upper 16-bits of memory source/destination address for DMA master channel 6 */
#define USB_DMA6COUNTLOW 0xffc040d0 /* Lower 16-bits of byte count of DMA transfer for DMA master channel 6 */
#define USB_DMA6COUNTHIGH 0xffc040d4 /* Upper 16-bits of byte count of DMA transfer for DMA master channel 6 */
/* USB Channel 7 Config Registers */
#define USB_DMA7CONTROL 0xffc040e4 /* DMA master channel 7 configuration */
#define USB_DMA7ADDRLOW 0xffc040e8 /* Lower 16-bits of memory source/destination address for DMA master channel 7 */
#define USB_DMA7ADDRHIGH 0xffc040ec /* Upper 16-bits of memory source/destination address for DMA master channel 7 */
#define USB_DMA7COUNTLOW 0xffc040f0 /* Lower 16-bits of byte count of DMA transfer for DMA master channel 7 */
#define USB_DMA7COUNTHIGH 0xffc040f4 /* Upper 16-bits of byte count of DMA transfer for DMA master channel 7 */
/* Keypad Registers */
#define KPAD_CTL 0xffc04100 /* Controls keypad module enable and disable */
#define KPAD_PRESCALE 0xffc04104 /* Establish a time base for programing the KPAD_MSEL register */
#define KPAD_MSEL 0xffc04108 /* Selects delay parameters for keypad interface sensitivity */
#define KPAD_ROWCOL 0xffc0410c /* Captures the row and column output values of the keys pressed */
#define KPAD_STAT 0xffc04110 /* Holds and clears the status of the keypad interface interrupt */
#define KPAD_SOFTEVAL 0xffc04114 /* Lets software force keypad interface to check for keys being pressed */
/* ********************************************************** */
/* SINGLE BIT MACRO PAIRS (bit mask and negated one) */
/* and MULTI BIT READ MACROS */
/* ********************************************************** */
/* Bit masks for KPAD_CTL */
#define KPAD_EN 0x1 /* Keypad Enable */
#define KPAD_IRQMODE 0x6 /* Key Press Interrupt Enable */
#define KPAD_ROWEN 0x1c00 /* Row Enable Width */
#define KPAD_COLEN 0xe000 /* Column Enable Width */
/* Bit masks for KPAD_PRESCALE */
#define KPAD_PRESCALE_VAL 0x3f /* Key Prescale Value */
/* Bit masks for KPAD_MSEL */
#define DBON_SCALE 0xff /* Debounce Scale Value */
#define COLDRV_SCALE 0xff00 /* Column Driver Scale Value */
/* Bit masks for KPAD_ROWCOL */
#define KPAD_ROW 0xff /* Rows Pressed */
#define KPAD_COL 0xff00 /* Columns Pressed */
/* Bit masks for KPAD_STAT */
#define KPAD_IRQ 0x1 /* Keypad Interrupt Status */
#define KPAD_MROWCOL 0x6 /* Multiple Row/Column Keypress Status */
#define KPAD_PRESSED 0x8 /* Key press current status */
/* Bit masks for KPAD_SOFTEVAL */
#define KPAD_SOFTEVAL_E 0x2 /* Software Programmable Force Evaluate */
/* Bit masks for SDH_COMMAND */
#define CMD_IDX 0x3f /* Command Index */
#define CMD_RSP 0x40 /* Response */
#define CMD_L_RSP 0x80 /* Long Response */
#define CMD_INT_E 0x100 /* Command Interrupt */
#define CMD_PEND_E 0x200 /* Command Pending */
#define CMD_E 0x400 /* Command Enable */
/* Bit masks for SDH_PWR_CTL */
#define PWR_ON 0x3 /* Power On */
#if 0
#define TBD 0x3c /* TBD */
#endif
#define SD_CMD_OD 0x40 /* Open Drain Output */
#define ROD_CTL 0x80 /* Rod Control */
/* Bit masks for SDH_CLK_CTL */
#define CLKDIV 0xff /* MC_CLK Divisor */
#define CLK_E 0x100 /* MC_CLK Bus Clock Enable */
#define PWR_SV_E 0x200 /* Power Save Enable */
#define CLKDIV_BYPASS 0x400 /* Bypass Divisor */
#define WIDE_BUS 0x800 /* Wide Bus Mode Enable */
/* Bit masks for SDH_RESP_CMD */
#define RESP_CMD 0x3f /* Response Command */
/* Bit masks for SDH_DATA_CTL */
#define DTX_E 0x1 /* Data Transfer Enable */
#define DTX_DIR 0x2 /* Data Transfer Direction */
#define DTX_MODE 0x4 /* Data Transfer Mode */
#define DTX_DMA_E 0x8 /* Data Transfer DMA Enable */
#define DTX_BLK_LGTH 0xf0 /* Data Transfer Block Length */
/* Bit masks for SDH_STATUS */
#define CMD_CRC_FAIL 0x1 /* CMD CRC Fail */
#define DAT_CRC_FAIL 0x2 /* Data CRC Fail */
#define CMD_TIME_OUT 0x4 /* CMD Time Out */
#define DAT_TIME_OUT 0x8 /* Data Time Out */
#define TX_UNDERRUN 0x10 /* Transmit Underrun */
#define RX_OVERRUN 0x20 /* Receive Overrun */
#define CMD_RESP_END 0x40 /* CMD Response End */
#define CMD_SENT 0x80 /* CMD Sent */
#define DAT_END 0x100 /* Data End */
#define START_BIT_ERR 0x200 /* Start Bit Error */
#define DAT_BLK_END 0x400 /* Data Block End */
#define CMD_ACT 0x800 /* CMD Active */
#define TX_ACT 0x1000 /* Transmit Active */
#define RX_ACT 0x2000 /* Receive Active */
#define TX_FIFO_STAT 0x4000 /* Transmit FIFO Status */
#define RX_FIFO_STAT 0x8000 /* Receive FIFO Status */
#define TX_FIFO_FULL 0x10000 /* Transmit FIFO Full */
#define RX_FIFO_FULL 0x20000 /* Receive FIFO Full */
#define TX_FIFO_ZERO 0x40000 /* Transmit FIFO Empty */
#define RX_DAT_ZERO 0x80000 /* Receive FIFO Empty */
#define TX_DAT_RDY 0x100000 /* Transmit Data Available */
#define RX_FIFO_RDY 0x200000 /* Receive Data Available */
/* Bit masks for SDH_STATUS_CLR */
#define CMD_CRC_FAIL_STAT 0x1 /* CMD CRC Fail Status */
#define DAT_CRC_FAIL_STAT 0x2 /* Data CRC Fail Status */
#define CMD_TIMEOUT_STAT 0x4 /* CMD Time Out Status */
#define DAT_TIMEOUT_STAT 0x8 /* Data Time Out status */
#define TX_UNDERRUN_STAT 0x10 /* Transmit Underrun Status */
#define RX_OVERRUN_STAT 0x20 /* Receive Overrun Status */
#define CMD_RESP_END_STAT 0x40 /* CMD Response End Status */
#define CMD_SENT_STAT 0x80 /* CMD Sent Status */
#define DAT_END_STAT 0x100 /* Data End Status */
#define START_BIT_ERR_STAT 0x200 /* Start Bit Error Status */
#define DAT_BLK_END_STAT 0x400 /* Data Block End Status */
/* Bit masks for SDH_MASK0 */
#define CMD_CRC_FAIL_MASK 0x1 /* CMD CRC Fail Mask */
#define DAT_CRC_FAIL_MASK 0x2 /* Data CRC Fail Mask */
#define CMD_TIMEOUT_MASK 0x4 /* CMD Time Out Mask */
#define DAT_TIMEOUT_MASK 0x8 /* Data Time Out Mask */
#define TX_UNDERRUN_MASK 0x10 /* Transmit Underrun Mask */
#define RX_OVERRUN_MASK 0x20 /* Receive Overrun Mask */
#define CMD_RESP_END_MASK 0x40 /* CMD Response End Mask */
#define CMD_SENT_MASK 0x80 /* CMD Sent Mask */
#define DAT_END_MASK 0x100 /* Data End Mask */
#define START_BIT_ERR_MASK 0x200 /* Start Bit Error Mask */
#define DAT_BLK_END_MASK 0x400 /* Data Block End Mask */
#define CMD_ACT_MASK 0x800 /* CMD Active Mask */
#define TX_ACT_MASK 0x1000 /* Transmit Active Mask */
#define RX_ACT_MASK 0x2000 /* Receive Active Mask */
#define TX_FIFO_STAT_MASK 0x4000 /* Transmit FIFO Status Mask */
#define RX_FIFO_STAT_MASK 0x8000 /* Receive FIFO Status Mask */
#define TX_FIFO_FULL_MASK 0x10000 /* Transmit FIFO Full Mask */
#define RX_FIFO_FULL_MASK 0x20000 /* Receive FIFO Full Mask */
#define TX_FIFO_ZERO_MASK 0x40000 /* Transmit FIFO Empty Mask */
#define RX_DAT_ZERO_MASK 0x80000 /* Receive FIFO Empty Mask */
#define TX_DAT_RDY_MASK 0x100000 /* Transmit Data Available Mask */
#define RX_FIFO_RDY_MASK 0x200000 /* Receive Data Available Mask */
/* Bit masks for SDH_FIFO_CNT */
#define FIFO_COUNT 0x7fff /* FIFO Count */
/* Bit masks for SDH_E_STATUS */
#define SDIO_INT_DET 0x2 /* SDIO Int Detected */
#define SD_CARD_DET 0x10 /* SD Card Detect */
/* Bit masks for SDH_E_MASK */
#define SDIO_MSK 0x2 /* Mask SDIO Int Detected */
#define SCD_MSK 0x40 /* Mask Card Detect */
/* Bit masks for SDH_CFG */
#define CLKS_EN 0x1 /* Clocks Enable */
#define SD4E 0x4 /* SDIO 4-Bit Enable */
#define MWE 0x8 /* Moving Window Enable */
#define SD_RST 0x10 /* SDMMC Reset */
#define PUP_SDDAT 0x20 /* Pull-up SD_DAT */
#define PUP_SDDAT3 0x40 /* Pull-up SD_DAT3 */
#define PD_SDDAT3 0x80 /* Pull-down SD_DAT3 */
/* Bit masks for SDH_RD_WAIT_EN */
#define RWR 0x1 /* Read Wait Request */
/* Bit masks for ATAPI_CONTROL */
#define PIO_START 0x1 /* Start PIO/Reg Op */
#define MULTI_START 0x2 /* Start Multi-DMA Op */
#define ULTRA_START 0x4 /* Start Ultra-DMA Op */
#define XFER_DIR 0x8 /* Transfer Direction */
#define IORDY_EN 0x10 /* IORDY Enable */
#define FIFO_FLUSH 0x20 /* Flush FIFOs */
#define SOFT_RST 0x40 /* Soft Reset */
#define DEV_RST 0x80 /* Device Reset */
#define TFRCNT_RST 0x100 /* Trans Count Reset */
#define END_ON_TERM 0x200 /* End/Terminate Select */
#define PIO_USE_DMA 0x400 /* PIO-DMA Enable */
#define UDMAIN_FIFO_THRS 0xf000 /* Ultra DMA-IN FIFO Threshold */
/* Bit masks for ATAPI_STATUS */
#define PIO_XFER_ON 0x1 /* PIO transfer in progress */
#define MULTI_XFER_ON 0x2 /* Multi-word DMA transfer in progress */
#define ULTRA_XFER_ON 0x4 /* Ultra DMA transfer in progress */
#define ULTRA_IN_FL 0xf0 /* Ultra DMA Input FIFO Level */
/* Bit masks for ATAPI_DEV_ADDR */
#define DEV_ADDR 0x1f /* Device Address */
/* Bit masks for ATAPI_INT_MASK */
#define ATAPI_DEV_INT_MASK 0x1 /* Device interrupt mask */
#define PIO_DONE_MASK 0x2 /* PIO transfer done interrupt mask */
#define MULTI_DONE_MASK 0x4 /* Multi-DMA transfer done interrupt mask */
#define UDMAIN_DONE_MASK 0x8 /* Ultra-DMA in transfer done interrupt mask */
#define UDMAOUT_DONE_MASK 0x10 /* Ultra-DMA out transfer done interrupt mask */
#define HOST_TERM_XFER_MASK 0x20 /* Host terminate current transfer interrupt mask */
#define MULTI_TERM_MASK 0x40 /* Device terminate Multi-DMA transfer interrupt mask */
#define UDMAIN_TERM_MASK 0x80 /* Device terminate Ultra-DMA-in transfer interrupt mask */
#define UDMAOUT_TERM_MASK 0x100 /* Device terminate Ultra-DMA-out transfer interrupt mask */
/* Bit masks for ATAPI_INT_STATUS */
#define ATAPI_DEV_INT 0x1 /* Device interrupt status */
#define PIO_DONE_INT 0x2 /* PIO transfer done interrupt status */
#define MULTI_DONE_INT 0x4 /* Multi-DMA transfer done interrupt status */
#define UDMAIN_DONE_INT 0x8 /* Ultra-DMA in transfer done interrupt status */
#define UDMAOUT_DONE_INT 0x10 /* Ultra-DMA out transfer done interrupt status */
#define HOST_TERM_XFER_INT 0x20 /* Host terminate current transfer interrupt status */
#define MULTI_TERM_INT 0x40 /* Device terminate Multi-DMA transfer interrupt status */
#define UDMAIN_TERM_INT 0x80 /* Device terminate Ultra-DMA-in transfer interrupt status */
#define UDMAOUT_TERM_INT 0x100 /* Device terminate Ultra-DMA-out transfer interrupt status */
/* Bit masks for ATAPI_LINE_STATUS */
#define ATAPI_INTR 0x1 /* Device interrupt to host line status */
#define ATAPI_DASP 0x2 /* Device dasp to host line status */
#define ATAPI_CS0N 0x4 /* ATAPI chip select 0 line status */
#define ATAPI_CS1N 0x8 /* ATAPI chip select 1 line status */
#define ATAPI_ADDR 0x70 /* ATAPI address line status */
#define ATAPI_DMAREQ 0x80 /* ATAPI DMA request line status */
#define ATAPI_DMAACKN 0x100 /* ATAPI DMA acknowledge line status */
#define ATAPI_DIOWN 0x200 /* ATAPI write line status */
#define ATAPI_DIORN 0x400 /* ATAPI read line status */
#define ATAPI_IORDY 0x800 /* ATAPI IORDY line status */
/* Bit masks for ATAPI_SM_STATE */
#define PIO_CSTATE 0xf /* PIO mode state machine current state */
#define DMA_CSTATE 0xf0 /* DMA mode state machine current state */
#define UDMAIN_CSTATE 0xf00 /* Ultra DMA-In mode state machine current state */
#define UDMAOUT_CSTATE 0xf000 /* ATAPI IORDY line status */
/* Bit masks for ATAPI_TERMINATE */
#define ATAPI_HOST_TERM 0x1 /* Host terminationation */
/* Bit masks for ATAPI_REG_TIM_0 */
#define T2_REG 0xff /* End of cycle time for register access transfers */
#define TEOC_REG 0xff00 /* Selects DIOR/DIOW pulsewidth */
/* Bit masks for ATAPI_PIO_TIM_0 */
#define T1_REG 0xf /* Time from address valid to DIOR/DIOW */
#define T2_REG_PIO 0xff0 /* DIOR/DIOW pulsewidth */
#define T4_REG 0xf000 /* DIOW data hold */
/* Bit masks for ATAPI_PIO_TIM_1 */
#define TEOC_REG_PIO 0xff /* End of cycle time for PIO access transfers. */
/* Bit masks for ATAPI_MULTI_TIM_0 */
#define TD 0xff /* DIOR/DIOW asserted pulsewidth */
#define TM 0xff00 /* Time from address valid to DIOR/DIOW */
/* Bit masks for ATAPI_MULTI_TIM_1 */
#define TKW 0xff /* Selects DIOW negated pulsewidth */
#define TKR 0xff00 /* Selects DIOR negated pulsewidth */
/* Bit masks for ATAPI_MULTI_TIM_2 */
#define TH 0xff /* Selects DIOW data hold */
#define TEOC 0xff00 /* Selects end of cycle for DMA */
/* Bit masks for ATAPI_ULTRA_TIM_0 */
#define TACK 0xff /* Selects setup and hold times for TACK */
#define TENV 0xff00 /* Selects envelope time */
/* Bit masks for ATAPI_ULTRA_TIM_1 */
#define TDVS 0xff /* Selects data valid setup time */
#define TCYC_TDVS 0xff00 /* Selects cycle time - TDVS time */
/* Bit masks for ATAPI_ULTRA_TIM_2 */
#define TSS 0xff /* Selects time from STROBE edge to negation of DMARQ or assertion of STOP */
#define TMLI 0xff00 /* Selects interlock time */
/* Bit masks for ATAPI_ULTRA_TIM_3 */
#define TZAH 0xff /* Selects minimum delay required for output */
#define READY_PAUSE 0xff00 /* Selects ready to pause */
/* Bit masks for USB_FADDR */
#define FUNCTION_ADDRESS 0x7f /* Function address */
/* Bit masks for USB_POWER */
#define ENABLE_SUSPENDM 0x1 /* enable SuspendM output */
#define SUSPEND_MODE 0x2 /* Suspend Mode indicator */
#define RESUME_MODE 0x4 /* DMA Mode */
#define RESET 0x8 /* Reset indicator */
#define HS_MODE 0x10 /* High Speed mode indicator */
#define HS_ENABLE 0x20 /* high Speed Enable */
#define SOFT_CONN 0x40 /* Soft connect */
#define ISO_UPDATE 0x80 /* Isochronous update */
/* Bit masks for USB_INTRTX */
#define EP0_TX 0x1 /* Tx Endpoint 0 interrupt */
#define EP1_TX 0x2 /* Tx Endpoint 1 interrupt */
#define EP2_TX 0x4 /* Tx Endpoint 2 interrupt */
#define EP3_TX 0x8 /* Tx Endpoint 3 interrupt */
#define EP4_TX 0x10 /* Tx Endpoint 4 interrupt */
#define EP5_TX 0x20 /* Tx Endpoint 5 interrupt */
#define EP6_TX 0x40 /* Tx Endpoint 6 interrupt */
#define EP7_TX 0x80 /* Tx Endpoint 7 interrupt */
/* Bit masks for USB_INTRRX */
#define EP1_RX 0x2 /* Rx Endpoint 1 interrupt */
#define EP2_RX 0x4 /* Rx Endpoint 2 interrupt */
#define EP3_RX 0x8 /* Rx Endpoint 3 interrupt */
#define EP4_RX 0x10 /* Rx Endpoint 4 interrupt */
#define EP5_RX 0x20 /* Rx Endpoint 5 interrupt */
#define EP6_RX 0x40 /* Rx Endpoint 6 interrupt */
#define EP7_RX 0x80 /* Rx Endpoint 7 interrupt */
/* Bit masks for USB_INTRTXE */
#define EP0_TX_E 0x1 /* Endpoint 0 interrupt Enable */
#define EP1_TX_E 0x2 /* Tx Endpoint 1 interrupt Enable */
#define EP2_TX_E 0x4 /* Tx Endpoint 2 interrupt Enable */
#define EP3_TX_E 0x8 /* Tx Endpoint 3 interrupt Enable */
#define EP4_TX_E 0x10 /* Tx Endpoint 4 interrupt Enable */
#define EP5_TX_E 0x20 /* Tx Endpoint 5 interrupt Enable */
#define EP6_TX_E 0x40 /* Tx Endpoint 6 interrupt Enable */
#define EP7_TX_E 0x80 /* Tx Endpoint 7 interrupt Enable */
/* Bit masks for USB_INTRRXE */
#define EP1_RX_E 0x2 /* Rx Endpoint 1 interrupt Enable */
#define EP2_RX_E 0x4 /* Rx Endpoint 2 interrupt Enable */
#define EP3_RX_E 0x8 /* Rx Endpoint 3 interrupt Enable */
#define EP4_RX_E 0x10 /* Rx Endpoint 4 interrupt Enable */
#define EP5_RX_E 0x20 /* Rx Endpoint 5 interrupt Enable */
#define EP6_RX_E 0x40 /* Rx Endpoint 6 interrupt Enable */
#define EP7_RX_E 0x80 /* Rx Endpoint 7 interrupt Enable */
/* Bit masks for USB_INTRUSB */
#define SUSPEND_B 0x1 /* Suspend indicator */
#define RESUME_B 0x2 /* Resume indicator */
#define RESET_OR_BABLE_B 0x4 /* Reset/babble indicator */
#define SOF_B 0x8 /* Start of frame */
#define CONN_B 0x10 /* Connection indicator */
#define DISCON_B 0x20 /* Disconnect indicator */
#define SESSION_REQ_B 0x40 /* Session Request */
#define VBUS_ERROR_B 0x80 /* Vbus threshold indicator */
/* Bit masks for USB_INTRUSBE */
#define SUSPEND_BE 0x1 /* Suspend indicator int enable */
#define RESUME_BE 0x2 /* Resume indicator int enable */
#define RESET_OR_BABLE_BE 0x4 /* Reset/babble indicator int enable */
#define SOF_BE 0x8 /* Start of frame int enable */
#define CONN_BE 0x10 /* Connection indicator int enable */
#define DISCON_BE 0x20 /* Disconnect indicator int enable */
#define SESSION_REQ_BE 0x40 /* Session Request int enable */
#define VBUS_ERROR_BE 0x80 /* Vbus threshold indicator int enable */
/* Bit masks for USB_FRAME */
#define FRAME_NUMBER 0x7ff /* Frame number */
/* Bit masks for USB_INDEX */
#define SELECTED_ENDPOINT 0xf /* selected endpoint */
/* Bit masks for USB_GLOBAL_CTL */
#define GLOBAL_ENA 0x1 /* enables USB module */
#define EP1_TX_ENA 0x2 /* Transmit endpoint 1 enable */
#define EP2_TX_ENA 0x4 /* Transmit endpoint 2 enable */
#define EP3_TX_ENA 0x8 /* Transmit endpoint 3 enable */
#define EP4_TX_ENA 0x10 /* Transmit endpoint 4 enable */
#define EP5_TX_ENA 0x20 /* Transmit endpoint 5 enable */
#define EP6_TX_ENA 0x40 /* Transmit endpoint 6 enable */
#define EP7_TX_ENA 0x80 /* Transmit endpoint 7 enable */
#define EP1_RX_ENA 0x100 /* Receive endpoint 1 enable */
#define EP2_RX_ENA 0x200 /* Receive endpoint 2 enable */
#define EP3_RX_ENA 0x400 /* Receive endpoint 3 enable */
#define EP4_RX_ENA 0x800 /* Receive endpoint 4 enable */
#define EP5_RX_ENA 0x1000 /* Receive endpoint 5 enable */
#define EP6_RX_ENA 0x2000 /* Receive endpoint 6 enable */
#define EP7_RX_ENA 0x4000 /* Receive endpoint 7 enable */
/* Bit masks for USB_OTG_DEV_CTL */
#define SESSION 0x1 /* session indicator */
#define HOST_REQ 0x2 /* Host negotiation request */
#define HOST_MODE 0x4 /* indicates USBDRC is a host */
#define VBUS0 0x8 /* Vbus level indicator[0] */
#define VBUS1 0x10 /* Vbus level indicator[1] */
#define LSDEV 0x20 /* Low-speed indicator */
#define FSDEV 0x40 /* Full or High-speed indicator */
#define B_DEVICE 0x80 /* A' or 'B' device indicator */
/* Bit masks for USB_OTG_VBUS_IRQ */
#define DRIVE_VBUS_ON 0x1 /* indicator to drive VBUS control circuit */
#define DRIVE_VBUS_OFF 0x2 /* indicator to shut off charge pump */
#define CHRG_VBUS_START 0x4 /* indicator for external circuit to start charging VBUS */
#define CHRG_VBUS_END 0x8 /* indicator for external circuit to end charging VBUS */
#define DISCHRG_VBUS_START 0x10 /* indicator to start discharging VBUS */
#define DISCHRG_VBUS_END 0x20 /* indicator to stop discharging VBUS */
/* Bit masks for USB_OTG_VBUS_MASK */
#define DRIVE_VBUS_ON_ENA 0x1 /* enable DRIVE_VBUS_ON interrupt */
#define DRIVE_VBUS_OFF_ENA 0x2 /* enable DRIVE_VBUS_OFF interrupt */
#define CHRG_VBUS_START_ENA 0x4 /* enable CHRG_VBUS_START interrupt */
#define CHRG_VBUS_END_ENA 0x8 /* enable CHRG_VBUS_END interrupt */
#define DISCHRG_VBUS_START_ENA 0x10 /* enable DISCHRG_VBUS_START interrupt */
#define DISCHRG_VBUS_END_ENA 0x20 /* enable DISCHRG_VBUS_END interrupt */
/* Bit masks for USB_CSR0 */
#define RXPKTRDY 0x1 /* data packet receive indicator */
#define TXPKTRDY 0x2 /* data packet in FIFO indicator */
#define STALL_SENT 0x4 /* STALL handshake sent */
#define DATAEND 0x8 /* Data end indicator */
#define SETUPEND 0x10 /* Setup end */
#define SENDSTALL 0x20 /* Send STALL handshake */
#define SERVICED_RXPKTRDY 0x40 /* used to clear the RxPktRdy bit */
#define SERVICED_SETUPEND 0x80 /* used to clear the SetupEnd bit */
#define FLUSHFIFO 0x100 /* flush endpoint FIFO */
#define STALL_RECEIVED_H 0x4 /* STALL handshake received host mode */
#define SETUPPKT_H 0x8 /* send Setup token host mode */
#define ERROR_H 0x10 /* timeout error indicator host mode */
#define REQPKT_H 0x20 /* Request an IN transaction host mode */
#define STATUSPKT_H 0x40 /* Status stage transaction host mode */
#define NAK_TIMEOUT_H 0x80 /* EP0 halted after a NAK host mode */
/* Bit masks for USB_COUNT0 */
#define EP0_RX_COUNT 0x7f /* number of received bytes in EP0 FIFO */
/* Bit masks for USB_NAKLIMIT0 */
#define EP0_NAK_LIMIT 0x1f /* number of frames/micro frames after which EP0 timeouts */
/* Bit masks for USB_TX_MAX_PACKET */
#define MAX_PACKET_SIZE_T 0x7ff /* maximum data pay load in a frame */
/* Bit masks for USB_RX_MAX_PACKET */
#define MAX_PACKET_SIZE_R 0x7ff /* maximum data pay load in a frame */
/* Bit masks for USB_TXCSR */
#define TXPKTRDY_T 0x1 /* data packet in FIFO indicator */
#define FIFO_NOT_EMPTY_T 0x2 /* FIFO not empty */
#define UNDERRUN_T 0x4 /* TxPktRdy not set for an IN token */
#define FLUSHFIFO_T 0x8 /* flush endpoint FIFO */
#define STALL_SEND_T 0x10 /* issue a Stall handshake */
#define STALL_SENT_T 0x20 /* Stall handshake transmitted */
#define CLEAR_DATATOGGLE_T 0x40 /* clear endpoint data toggle */
#define INCOMPTX_T 0x80 /* indicates that a large packet is split */
#define DMAREQMODE_T 0x400 /* DMA mode (0 or 1) selection */
#define FORCE_DATATOGGLE_T 0x800 /* Force data toggle */
#define DMAREQ_ENA_T 0x1000 /* Enable DMA request for Tx EP */
#define ISO_T 0x4000 /* enable Isochronous transfers */
#define AUTOSET_T 0x8000 /* allows TxPktRdy to be set automatically */
#define ERROR_TH 0x4 /* error condition host mode */
#define STALL_RECEIVED_TH 0x20 /* Stall handshake received host mode */
#define NAK_TIMEOUT_TH 0x80 /* NAK timeout host mode */
/* Bit masks for USB_TXCOUNT */
#define TX_COUNT 0x1fff /* Number of bytes to be written to the selected endpoint Tx FIFO */
/* Bit masks for USB_RXCSR */
#define RXPKTRDY_R 0x1 /* data packet in FIFO indicator */
#define FIFO_FULL_R 0x2 /* FIFO not empty */
#define OVERRUN_R 0x4 /* TxPktRdy not set for an IN token */
#define DATAERROR_R 0x8 /* Out packet cannot be loaded into Rx FIFO */
#define FLUSHFIFO_R 0x10 /* flush endpoint FIFO */
#define STALL_SEND_R 0x20 /* issue a Stall handshake */
#define STALL_SENT_R 0x40 /* Stall handshake transmitted */
#define CLEAR_DATATOGGLE_R 0x80 /* clear endpoint data toggle */
#define INCOMPRX_R 0x100 /* indicates that a large packet is split */
#define DMAREQMODE_R 0x800 /* DMA mode (0 or 1) selection */
#define DISNYET_R 0x1000 /* disable Nyet handshakes */
#define DMAREQ_ENA_R 0x2000 /* Enable DMA request for Tx EP */
#define ISO_R 0x4000 /* enable Isochronous transfers */
#define AUTOCLEAR_R 0x8000 /* allows TxPktRdy to be set automatically */
#define ERROR_RH 0x4 /* TxPktRdy not set for an IN token host mode */
#define REQPKT_RH 0x20 /* request an IN transaction host mode */
#define STALL_RECEIVED_RH 0x40 /* Stall handshake received host mode */
#define INCOMPRX_RH 0x100 /* indicates that a large packet is split host mode */
#define DMAREQMODE_RH 0x800 /* DMA mode (0 or 1) selection host mode */
#define AUTOREQ_RH 0x4000 /* sets ReqPkt automatically host mode */
/* Bit masks for USB_RXCOUNT */
#define RX_COUNT 0x1fff /* Number of received bytes in the packet in the Rx FIFO */
/* Bit masks for USB_TXTYPE */
#define TARGET_EP_NO_T 0xf /* EP number */
#define PROTOCOL_T 0xc /* transfer type */
/* Bit masks for USB_TXINTERVAL */
#define TX_POLL_INTERVAL 0xff /* polling interval for selected Tx EP */
/* Bit masks for USB_RXTYPE */
#define TARGET_EP_NO_R 0xf /* EP number */
#define PROTOCOL_R 0xc /* transfer type */
/* Bit masks for USB_RXINTERVAL */
#define RX_POLL_INTERVAL 0xff /* polling interval for selected Rx EP */
/* Bit masks for USB_DMA_INTERRUPT */
#define DMA0_INT 0x1 /* DMA0 pending interrupt */
#define DMA1_INT 0x2 /* DMA1 pending interrupt */
#define DMA2_INT 0x4 /* DMA2 pending interrupt */
#define DMA3_INT 0x8 /* DMA3 pending interrupt */
#define DMA4_INT 0x10 /* DMA4 pending interrupt */
#define DMA5_INT 0x20 /* DMA5 pending interrupt */
#define DMA6_INT 0x40 /* DMA6 pending interrupt */
#define DMA7_INT 0x80 /* DMA7 pending interrupt */
/* Bit masks for USB_DMAxCONTROL */
#define DMA_ENA 0x1 /* DMA enable */
#define DIRECTION 0x2 /* direction of DMA transfer */
#define MODE 0x4 /* DMA Bus error */
#define INT_ENA 0x8 /* Interrupt enable */
#define EPNUM 0xf0 /* EP number */
#define BUSERROR 0x100 /* DMA Bus error */
/* Bit masks for USB_DMAxADDRHIGH */
#define DMA_ADDR_HIGH 0xffff /* Upper 16-bits of memory source/destination address for the DMA master channel */
/* Bit masks for USB_DMAxADDRLOW */
#define DMA_ADDR_LOW 0xffff /* Lower 16-bits of memory source/destination address for the DMA master channel */
/* Bit masks for USB_DMAxCOUNTHIGH */
#define DMA_COUNT_HIGH 0xffff /* Upper 16-bits of byte count of DMA transfer for DMA master channel */
/* Bit masks for USB_DMAxCOUNTLOW */
#define DMA_COUNT_LOW 0xffff /* Lower 16-bits of byte count of DMA transfer for DMA master channel */
/* ******************************************* */
/* MULTI BIT MACRO ENUMERATIONS */
/* ******************************************* */
#endif /* _DEF_BF542_H */