Linux-2.6.33.2/arch/powerpc/kernel/head_fsl_booke.S
/*
* Kernel execution entry point code.
*
* Copyright (c) 1995-1996 Gary Thomas <gdt@linuxppc.org>
* Initial PowerPC version.
* Copyright (c) 1996 Cort Dougan <cort@cs.nmt.edu>
* Rewritten for PReP
* Copyright (c) 1996 Paul Mackerras <paulus@cs.anu.edu.au>
* Low-level exception handers, MMU support, and rewrite.
* Copyright (c) 1997 Dan Malek <dmalek@jlc.net>
* PowerPC 8xx modifications.
* Copyright (c) 1998-1999 TiVo, Inc.
* PowerPC 403GCX modifications.
* Copyright (c) 1999 Grant Erickson <grant@lcse.umn.edu>
* PowerPC 403GCX/405GP modifications.
* Copyright 2000 MontaVista Software Inc.
* PPC405 modifications
* PowerPC 403GCX/405GP modifications.
* Author: MontaVista Software, Inc.
* frank_rowand@mvista.com or source@mvista.com
* debbie_chu@mvista.com
* Copyright 2002-2004 MontaVista Software, Inc.
* PowerPC 44x support, Matt Porter <mporter@kernel.crashing.org>
* Copyright 2004 Freescale Semiconductor, Inc
* PowerPC e500 modifications, Kumar Gala <galak@kernel.crashing.org>
*
* This program is free software; you can redistribute it and/or modify it
* under the terms of the GNU General Public License as published by the
* Free Software Foundation; either version 2 of the License, or (at your
* option) any later version.
*/
#include <linux/init.h>
#include <linux/threads.h>
#include <asm/processor.h>
#include <asm/page.h>
#include <asm/mmu.h>
#include <asm/pgtable.h>
#include <asm/cputable.h>
#include <asm/thread_info.h>
#include <asm/ppc_asm.h>
#include <asm/asm-offsets.h>
#include <asm/cache.h>
#include "head_booke.h"
/* As with the other PowerPC ports, it is expected that when code
* execution begins here, the following registers contain valid, yet
* optional, information:
*
* r3 - Board info structure pointer (DRAM, frequency, MAC address, etc.)
* r4 - Starting address of the init RAM disk
* r5 - Ending address of the init RAM disk
* r6 - Start of kernel command line string (e.g. "mem=128")
* r7 - End of kernel command line string
*
*/
__HEAD
_ENTRY(_stext);
_ENTRY(_start);
/*
* Reserve a word at a fixed location to store the address
* of abatron_pteptrs
*/
nop
/*
* Save parameters we are passed
*/
mr r31,r3
mr r30,r4
mr r29,r5
mr r28,r6
mr r27,r7
li r25,0 /* phys kernel start (low) */
li r24,0 /* CPU number */
li r23,0 /* phys kernel start (high) */
/* We try to not make any assumptions about how the boot loader
* setup or used the TLBs. We invalidate all mappings from the
* boot loader and load a single entry in TLB1[0] to map the
* first 64M of kernel memory. Any boot info passed from the
* bootloader needs to live in this first 64M.
*
* Requirement on bootloader:
* - The page we're executing in needs to reside in TLB1 and
* have IPROT=1. If not an invalidate broadcast could
* evict the entry we're currently executing in.
*
* r3 = Index of TLB1 were executing in
* r4 = Current MSR[IS]
* r5 = Index of TLB1 temp mapping
*
* Later in mapin_ram we will correctly map lowmem, and resize TLB1[0]
* if needed
*/
_ENTRY(__early_start)
/* 1. Find the index of the entry we're executing in */
bl invstr /* Find our address */
invstr: mflr r6 /* Make it accessible */
mfmsr r7
rlwinm r4,r7,27,31,31 /* extract MSR[IS] */
mfspr r7, SPRN_PID0
slwi r7,r7,16
or r7,r7,r4
mtspr SPRN_MAS6,r7
tlbsx 0,r6 /* search MSR[IS], SPID=PID0 */
mfspr r7,SPRN_MAS1
andis. r7,r7,MAS1_VALID@h
bne match_TLB
mfspr r7,SPRN_MMUCFG
rlwinm r7,r7,21,28,31 /* extract MMUCFG[NPIDS] */
cmpwi r7,3
bne match_TLB /* skip if NPIDS != 3 */
mfspr r7,SPRN_PID1
slwi r7,r7,16
or r7,r7,r4
mtspr SPRN_MAS6,r7
tlbsx 0,r6 /* search MSR[IS], SPID=PID1 */
mfspr r7,SPRN_MAS1
andis. r7,r7,MAS1_VALID@h
bne match_TLB
mfspr r7, SPRN_PID2
slwi r7,r7,16
or r7,r7,r4
mtspr SPRN_MAS6,r7
tlbsx 0,r6 /* Fall through, we had to match */
match_TLB:
mfspr r7,SPRN_MAS0
rlwinm r3,r7,16,20,31 /* Extract MAS0(Entry) */
mfspr r7,SPRN_MAS1 /* Insure IPROT set */
oris r7,r7,MAS1_IPROT@h
mtspr SPRN_MAS1,r7
tlbwe
/* 2. Invalidate all entries except the entry we're executing in */
mfspr r9,SPRN_TLB1CFG
andi. r9,r9,0xfff
li r6,0 /* Set Entry counter to 0 */
1: lis r7,0x1000 /* Set MAS0(TLBSEL) = 1 */
rlwimi r7,r6,16,4,15 /* Setup MAS0 = TLBSEL | ESEL(r6) */
mtspr SPRN_MAS0,r7
tlbre
mfspr r7,SPRN_MAS1
rlwinm r7,r7,0,2,31 /* Clear MAS1 Valid and IPROT */
cmpw r3,r6
beq skpinv /* Dont update the current execution TLB */
mtspr SPRN_MAS1,r7
tlbwe
isync
skpinv: addi r6,r6,1 /* Increment */
cmpw r6,r9 /* Are we done? */
bne 1b /* If not, repeat */
/* Invalidate TLB0 */
li r6,0x04
tlbivax 0,r6
TLBSYNC
/* Invalidate TLB1 */
li r6,0x0c
tlbivax 0,r6
TLBSYNC
/* 3. Setup a temp mapping and jump to it */
andi. r5, r3, 0x1 /* Find an entry not used and is non-zero */
addi r5, r5, 0x1
lis r7,0x1000 /* Set MAS0(TLBSEL) = 1 */
rlwimi r7,r3,16,4,15 /* Setup MAS0 = TLBSEL | ESEL(r3) */
mtspr SPRN_MAS0,r7
tlbre
/* grab and fixup the RPN */
mfspr r6,SPRN_MAS1 /* extract MAS1[SIZE] */
rlwinm r6,r6,25,27,31
li r8,-1
addi r6,r6,10
slw r6,r8,r6 /* convert to mask */
bl 1f /* Find our address */
1: mflr r7
mfspr r8,SPRN_MAS3
#ifdef CONFIG_PHYS_64BIT
mfspr r23,SPRN_MAS7
#endif
and r8,r6,r8
subfic r9,r6,-4096
and r9,r9,r7
or r25,r8,r9
ori r8,r25,(MAS3_SX|MAS3_SW|MAS3_SR)
/* Just modify the entry ID and EPN for the temp mapping */
lis r7,0x1000 /* Set MAS0(TLBSEL) = 1 */
rlwimi r7,r5,16,4,15 /* Setup MAS0 = TLBSEL | ESEL(r5) */
mtspr SPRN_MAS0,r7
xori r6,r4,1 /* Setup TMP mapping in the other Address space */
slwi r6,r6,12
oris r6,r6,(MAS1_VALID|MAS1_IPROT)@h
ori r6,r6,(MAS1_TSIZE(BOOK3E_PAGESZ_4K))@l
mtspr SPRN_MAS1,r6
mfspr r6,SPRN_MAS2
li r7,0 /* temp EPN = 0 */
rlwimi r7,r6,0,20,31
mtspr SPRN_MAS2,r7
mtspr SPRN_MAS3,r8
tlbwe
xori r6,r4,1
slwi r6,r6,5 /* setup new context with other address space */
bl 1f /* Find our address */
1: mflr r9
rlwimi r7,r9,0,20,31
addi r7,r7,24
mtspr SPRN_SRR0,r7
mtspr SPRN_SRR1,r6
rfi
/* 4. Clear out PIDs & Search info */
li r6,0
mtspr SPRN_MAS6,r6
mtspr SPRN_PID0,r6
mfspr r7,SPRN_MMUCFG
rlwinm r7,r7,21,28,31 /* extract MMUCFG[NPIDS] */
cmpwi r7,3
bne 2f /* skip if NPIDS != 3 */
mtspr SPRN_PID1,r6
mtspr SPRN_PID2,r6
/* 5. Invalidate mapping we started in */
2:
lis r7,0x1000 /* Set MAS0(TLBSEL) = 1 */
rlwimi r7,r3,16,4,15 /* Setup MAS0 = TLBSEL | ESEL(r3) */
mtspr SPRN_MAS0,r7
tlbre
mfspr r6,SPRN_MAS1
rlwinm r6,r6,0,2,0 /* clear IPROT */
mtspr SPRN_MAS1,r6
tlbwe
/* Invalidate TLB1 */
li r9,0x0c
tlbivax 0,r9
TLBSYNC
/* The mapping only needs to be cache-coherent on SMP */
#ifdef CONFIG_SMP
#define M_IF_SMP MAS2_M
#else
#define M_IF_SMP 0
#endif
/* 6. Setup KERNELBASE mapping in TLB1[0] */
lis r6,0x1000 /* Set MAS0(TLBSEL) = TLB1(1), ESEL = 0 */
mtspr SPRN_MAS0,r6
lis r6,(MAS1_VALID|MAS1_IPROT)@h
ori r6,r6,(MAS1_TSIZE(BOOK3E_PAGESZ_64M))@l
mtspr SPRN_MAS1,r6
lis r6,MAS2_VAL(PAGE_OFFSET, BOOK3E_PAGESZ_64M, M_IF_SMP)@h
ori r6,r6,MAS2_VAL(PAGE_OFFSET, BOOK3E_PAGESZ_64M, M_IF_SMP)@l
mtspr SPRN_MAS2,r6
mtspr SPRN_MAS3,r8
tlbwe
/* 7. Jump to KERNELBASE mapping */
lis r6,(KERNELBASE & ~0xfff)@h
ori r6,r6,(KERNELBASE & ~0xfff)@l
lis r7,MSR_KERNEL@h
ori r7,r7,MSR_KERNEL@l
bl 1f /* Find our address */
1: mflr r9
rlwimi r6,r9,0,20,31
addi r6,r6,(2f - 1b)
mtspr SPRN_SRR0,r6
mtspr SPRN_SRR1,r7
rfi /* start execution out of TLB1[0] entry */
/* 8. Clear out the temp mapping */
2: lis r7,0x1000 /* Set MAS0(TLBSEL) = 1 */
rlwimi r7,r5,16,4,15 /* Setup MAS0 = TLBSEL | ESEL(r5) */
mtspr SPRN_MAS0,r7
tlbre
mfspr r8,SPRN_MAS1
rlwinm r8,r8,0,2,0 /* clear IPROT */
mtspr SPRN_MAS1,r8
tlbwe
/* Invalidate TLB1 */
li r9,0x0c
tlbivax 0,r9
TLBSYNC
/* Establish the interrupt vector offsets */
SET_IVOR(0, CriticalInput);
SET_IVOR(1, MachineCheck);
SET_IVOR(2, DataStorage);
SET_IVOR(3, InstructionStorage);
SET_IVOR(4, ExternalInput);
SET_IVOR(5, Alignment);
SET_IVOR(6, Program);
SET_IVOR(7, FloatingPointUnavailable);
SET_IVOR(8, SystemCall);
SET_IVOR(9, AuxillaryProcessorUnavailable);
SET_IVOR(10, Decrementer);
SET_IVOR(11, FixedIntervalTimer);
SET_IVOR(12, WatchdogTimer);
SET_IVOR(13, DataTLBError);
SET_IVOR(14, InstructionTLBError);
SET_IVOR(15, DebugCrit);
/* Establish the interrupt vector base */
lis r4,interrupt_base@h /* IVPR only uses the high 16-bits */
mtspr SPRN_IVPR,r4
/* Setup the defaults for TLB entries */
li r2,(MAS4_TSIZED(BOOK3E_PAGESZ_4K))@l
#ifdef CONFIG_E200
oris r2,r2,MAS4_TLBSELD(1)@h
#endif
mtspr SPRN_MAS4, r2
#if 0
/* Enable DOZE */
mfspr r2,SPRN_HID0
oris r2,r2,HID0_DOZE@h
mtspr SPRN_HID0, r2
#endif
#if !defined(CONFIG_BDI_SWITCH)
/*
* The Abatron BDI JTAG debugger does not tolerate others
* mucking with the debug registers.
*/
lis r2,DBCR0_IDM@h
mtspr SPRN_DBCR0,r2
isync
/* clear any residual debug events */
li r2,-1
mtspr SPRN_DBSR,r2
#endif
#ifdef CONFIG_SMP
/* Check to see if we're the second processor, and jump
* to the secondary_start code if so
*/
mfspr r24,SPRN_PIR
cmpwi r24,0
bne __secondary_start
#endif
/*
* This is where the main kernel code starts.
*/
/* ptr to current */
lis r2,init_task@h
ori r2,r2,init_task@l
/* ptr to current thread */
addi r4,r2,THREAD /* init task's THREAD */
mtspr SPRN_SPRG_THREAD,r4
/* stack */
lis r1,init_thread_union@h
ori r1,r1,init_thread_union@l
li r0,0
stwu r0,THREAD_SIZE-STACK_FRAME_OVERHEAD(r1)
bl early_init
#ifdef CONFIG_RELOCATABLE
lis r3,kernstart_addr@ha
la r3,kernstart_addr@l(r3)
#ifdef CONFIG_PHYS_64BIT
stw r23,0(r3)
stw r25,4(r3)
#else
stw r25,0(r3)
#endif
#endif
/*
* Decide what sort of machine this is and initialize the MMU.
*/
mr r3,r31
mr r4,r30
mr r5,r29
mr r6,r28
mr r7,r27
bl machine_init
bl MMU_init
/* Setup PTE pointers for the Abatron bdiGDB */
lis r6, swapper_pg_dir@h
ori r6, r6, swapper_pg_dir@l
lis r5, abatron_pteptrs@h
ori r5, r5, abatron_pteptrs@l
lis r4, KERNELBASE@h
ori r4, r4, KERNELBASE@l
stw r5, 0(r4) /* Save abatron_pteptrs at a fixed location */
stw r6, 0(r5)
/* Let's move on */
lis r4,start_kernel@h
ori r4,r4,start_kernel@l
lis r3,MSR_KERNEL@h
ori r3,r3,MSR_KERNEL@l
mtspr SPRN_SRR0,r4
mtspr SPRN_SRR1,r3
rfi /* change context and jump to start_kernel */
/* Macros to hide the PTE size differences
*
* FIND_PTE -- walks the page tables given EA & pgdir pointer
* r10 -- EA of fault
* r11 -- PGDIR pointer
* r12 -- free
* label 2: is the bailout case
*
* if we find the pte (fall through):
* r11 is low pte word
* r12 is pointer to the pte
*/
#ifdef CONFIG_PTE_64BIT
#define FIND_PTE \
rlwinm r12, r10, 13, 19, 29; /* Compute pgdir/pmd offset */ \
lwzx r11, r12, r11; /* Get pgd/pmd entry */ \
rlwinm. r12, r11, 0, 0, 20; /* Extract pt base address */ \
beq 2f; /* Bail if no table */ \
rlwimi r12, r10, 23, 20, 28; /* Compute pte address */ \
lwz r11, 4(r12); /* Get pte entry */
#else
#define FIND_PTE \
rlwimi r11, r10, 12, 20, 29; /* Create L1 (pgdir/pmd) address */ \
lwz r11, 0(r11); /* Get L1 entry */ \
rlwinm. r12, r11, 0, 0, 19; /* Extract L2 (pte) base address */ \
beq 2f; /* Bail if no table */ \
rlwimi r12, r10, 22, 20, 29; /* Compute PTE address */ \
lwz r11, 0(r12); /* Get Linux PTE */
#endif
/*
* Interrupt vector entry code
*
* The Book E MMUs are always on so we don't need to handle
* interrupts in real mode as with previous PPC processors. In
* this case we handle interrupts in the kernel virtual address
* space.
*
* Interrupt vectors are dynamically placed relative to the
* interrupt prefix as determined by the address of interrupt_base.
* The interrupt vectors offsets are programmed using the labels
* for each interrupt vector entry.
*
* Interrupt vectors must be aligned on a 16 byte boundary.
* We align on a 32 byte cache line boundary for good measure.
*/
interrupt_base:
/* Critical Input Interrupt */
CRITICAL_EXCEPTION(0x0100, CriticalInput, unknown_exception)
/* Machine Check Interrupt */
#ifdef CONFIG_E200
/* no RFMCI, MCSRRs on E200 */
CRITICAL_EXCEPTION(0x0200, MachineCheck, machine_check_exception)
#else
MCHECK_EXCEPTION(0x0200, MachineCheck, machine_check_exception)
#endif
/* Data Storage Interrupt */
START_EXCEPTION(DataStorage)
NORMAL_EXCEPTION_PROLOG
mfspr r5,SPRN_ESR /* Grab the ESR, save it, pass arg3 */
stw r5,_ESR(r11)
mfspr r4,SPRN_DEAR /* Grab the DEAR, save it, pass arg2 */
andis. r10,r5,(ESR_ILK|ESR_DLK)@h
bne 1f
EXC_XFER_EE_LITE(0x0300, handle_page_fault)
1:
addi r3,r1,STACK_FRAME_OVERHEAD
EXC_XFER_EE_LITE(0x0300, CacheLockingException)
/* Instruction Storage Interrupt */
INSTRUCTION_STORAGE_EXCEPTION
/* External Input Interrupt */
EXCEPTION(0x0500, ExternalInput, do_IRQ, EXC_XFER_LITE)
/* Alignment Interrupt */
ALIGNMENT_EXCEPTION
/* Program Interrupt */
PROGRAM_EXCEPTION
/* Floating Point Unavailable Interrupt */
#ifdef CONFIG_PPC_FPU
FP_UNAVAILABLE_EXCEPTION
#else
#ifdef CONFIG_E200
/* E200 treats 'normal' floating point instructions as FP Unavail exception */
EXCEPTION(0x0800, FloatingPointUnavailable, program_check_exception, EXC_XFER_EE)
#else
EXCEPTION(0x0800, FloatingPointUnavailable, unknown_exception, EXC_XFER_EE)
#endif
#endif
/* System Call Interrupt */
START_EXCEPTION(SystemCall)
NORMAL_EXCEPTION_PROLOG
EXC_XFER_EE_LITE(0x0c00, DoSyscall)
/* Auxillary Processor Unavailable Interrupt */
EXCEPTION(0x2900, AuxillaryProcessorUnavailable, unknown_exception, EXC_XFER_EE)
/* Decrementer Interrupt */
DECREMENTER_EXCEPTION
/* Fixed Internal Timer Interrupt */
/* TODO: Add FIT support */
EXCEPTION(0x3100, FixedIntervalTimer, unknown_exception, EXC_XFER_EE)
/* Watchdog Timer Interrupt */
#ifdef CONFIG_BOOKE_WDT
CRITICAL_EXCEPTION(0x3200, WatchdogTimer, WatchdogException)
#else
CRITICAL_EXCEPTION(0x3200, WatchdogTimer, unknown_exception)
#endif
/* Data TLB Error Interrupt */
START_EXCEPTION(DataTLBError)
mtspr SPRN_SPRG_WSCRATCH0, r10 /* Save some working registers */
mtspr SPRN_SPRG_WSCRATCH1, r11
mtspr SPRN_SPRG_WSCRATCH2, r12
mtspr SPRN_SPRG_WSCRATCH3, r13
mfcr r11
mtspr SPRN_SPRG_WSCRATCH4, r11
mfspr r10, SPRN_DEAR /* Get faulting address */
/* If we are faulting a kernel address, we have to use the
* kernel page tables.
*/
lis r11, PAGE_OFFSET@h
cmplw 5, r10, r11
blt 5, 3f
lis r11, swapper_pg_dir@h
ori r11, r11, swapper_pg_dir@l
mfspr r12,SPRN_MAS1 /* Set TID to 0 */
rlwinm r12,r12,0,16,1
mtspr SPRN_MAS1,r12
b 4f
/* Get the PGD for the current thread */
3:
mfspr r11,SPRN_SPRG_THREAD
lwz r11,PGDIR(r11)
4:
/* Mask of required permission bits. Note that while we
* do copy ESR:ST to _PAGE_RW position as trying to write
* to an RO page is pretty common, we don't do it with
* _PAGE_DIRTY. We could do it, but it's a fairly rare
* event so I'd rather take the overhead when it happens
* rather than adding an instruction here. We should measure
* whether the whole thing is worth it in the first place
* as we could avoid loading SPRN_ESR completely in the first
* place...
*
* TODO: Is it worth doing that mfspr & rlwimi in the first
* place or can we save a couple of instructions here ?
*/
mfspr r12,SPRN_ESR
#ifdef CONFIG_PTE_64BIT
li r13,_PAGE_PRESENT
oris r13,r13,_PAGE_ACCESSED@h
#else
li r13,_PAGE_PRESENT|_PAGE_ACCESSED
#endif
rlwimi r13,r12,11,29,29
FIND_PTE
andc. r13,r13,r11 /* Check permission */
#ifdef CONFIG_PTE_64BIT
#ifdef CONFIG_SMP
subf r10,r11,r12 /* create false data dep */
lwzx r13,r11,r10 /* Get upper pte bits */
#else
lwz r13,0(r12) /* Get upper pte bits */
#endif
#endif
bne 2f /* Bail if permission/valid mismach */
/* Jump to common tlb load */
b finish_tlb_load
2:
/* The bailout. Restore registers to pre-exception conditions
* and call the heavyweights to help us out.
*/
mfspr r11, SPRN_SPRG_RSCRATCH4
mtcr r11
mfspr r13, SPRN_SPRG_RSCRATCH3
mfspr r12, SPRN_SPRG_RSCRATCH2
mfspr r11, SPRN_SPRG_RSCRATCH1
mfspr r10, SPRN_SPRG_RSCRATCH0
b DataStorage
/* Instruction TLB Error Interrupt */
/*
* Nearly the same as above, except we get our
* information from different registers and bailout
* to a different point.
*/
START_EXCEPTION(InstructionTLBError)
mtspr SPRN_SPRG_WSCRATCH0, r10 /* Save some working registers */
mtspr SPRN_SPRG_WSCRATCH1, r11
mtspr SPRN_SPRG_WSCRATCH2, r12
mtspr SPRN_SPRG_WSCRATCH3, r13
mfcr r11
mtspr SPRN_SPRG_WSCRATCH4, r11
mfspr r10, SPRN_SRR0 /* Get faulting address */
/* If we are faulting a kernel address, we have to use the
* kernel page tables.
*/
lis r11, PAGE_OFFSET@h
cmplw 5, r10, r11
blt 5, 3f
lis r11, swapper_pg_dir@h
ori r11, r11, swapper_pg_dir@l
mfspr r12,SPRN_MAS1 /* Set TID to 0 */
rlwinm r12,r12,0,16,1
mtspr SPRN_MAS1,r12
b 4f
/* Get the PGD for the current thread */
3:
mfspr r11,SPRN_SPRG_THREAD
lwz r11,PGDIR(r11)
4:
/* Make up the required permissions */
#ifdef CONFIG_PTE_64BIT
li r13,_PAGE_PRESENT | _PAGE_EXEC
oris r13,r13,_PAGE_ACCESSED@h
#else
li r13,_PAGE_PRESENT | _PAGE_ACCESSED | _PAGE_EXEC
#endif
FIND_PTE
andc. r13,r13,r11 /* Check permission */
#ifdef CONFIG_PTE_64BIT
#ifdef CONFIG_SMP
subf r10,r11,r12 /* create false data dep */
lwzx r13,r11,r10 /* Get upper pte bits */
#else
lwz r13,0(r12) /* Get upper pte bits */
#endif
#endif
bne 2f /* Bail if permission mismach */
/* Jump to common TLB load point */
b finish_tlb_load
2:
/* The bailout. Restore registers to pre-exception conditions
* and call the heavyweights to help us out.
*/
mfspr r11, SPRN_SPRG_RSCRATCH4
mtcr r11
mfspr r13, SPRN_SPRG_RSCRATCH3
mfspr r12, SPRN_SPRG_RSCRATCH2
mfspr r11, SPRN_SPRG_RSCRATCH1
mfspr r10, SPRN_SPRG_RSCRATCH0
b InstructionStorage
#ifdef CONFIG_SPE
/* SPE Unavailable */
START_EXCEPTION(SPEUnavailable)
NORMAL_EXCEPTION_PROLOG
bne load_up_spe
addi r3,r1,STACK_FRAME_OVERHEAD
EXC_XFER_EE_LITE(0x2010, KernelSPE)
#else
EXCEPTION(0x2020, SPEUnavailable, unknown_exception, EXC_XFER_EE)
#endif /* CONFIG_SPE */
/* SPE Floating Point Data */
#ifdef CONFIG_SPE
EXCEPTION(0x2030, SPEFloatingPointData, SPEFloatingPointException, EXC_XFER_EE);
/* SPE Floating Point Round */
EXCEPTION(0x2050, SPEFloatingPointRound, SPEFloatingPointRoundException, EXC_XFER_EE)
#else
EXCEPTION(0x2040, SPEFloatingPointData, unknown_exception, EXC_XFER_EE)
EXCEPTION(0x2050, SPEFloatingPointRound, unknown_exception, EXC_XFER_EE)
#endif /* CONFIG_SPE */
/* Performance Monitor */
EXCEPTION(0x2060, PerformanceMonitor, performance_monitor_exception, EXC_XFER_STD)
EXCEPTION(0x2070, Doorbell, doorbell_exception, EXC_XFER_STD)
CRITICAL_EXCEPTION(0x2080, CriticalDoorbell, unknown_exception)
/* Debug Interrupt */
DEBUG_DEBUG_EXCEPTION
DEBUG_CRIT_EXCEPTION
/*
* Local functions
*/
/*
* Both the instruction and data TLB miss get to this
* point to load the TLB.
* r10 - available to use
* r11 - TLB (info from Linux PTE)
* r12 - available to use
* r13 - upper bits of PTE (if PTE_64BIT) or available to use
* CR5 - results of addr >= PAGE_OFFSET
* MAS0, MAS1 - loaded with proper value when we get here
* MAS2, MAS3 - will need additional info from Linux PTE
* Upon exit, we reload everything and RFI.
*/
finish_tlb_load:
/*
* We set execute, because we don't have the granularity to
* properly set this at the page level (Linux problem).
* Many of these bits are software only. Bits we don't set
* here we (properly should) assume have the appropriate value.
*/
mfspr r12, SPRN_MAS2
#ifdef CONFIG_PTE_64BIT
rlwimi r12, r11, 32-19, 27, 31 /* extract WIMGE from pte */
#else
rlwimi r12, r11, 26, 27, 31 /* extract WIMGE from pte */
#endif
#ifdef CONFIG_SMP
ori r12, r12, MAS2_M
#endif
mtspr SPRN_MAS2, r12
#ifdef CONFIG_PTE_64BIT
rlwinm r12, r11, 32-2, 26, 31 /* Move in perm bits */
andi. r10, r11, _PAGE_DIRTY
bne 1f
li r10, MAS3_SW | MAS3_UW
andc r12, r12, r10
1: rlwimi r12, r13, 20, 0, 11 /* grab RPN[32:43] */
rlwimi r12, r11, 20, 12, 19 /* grab RPN[44:51] */
mtspr SPRN_MAS3, r12
BEGIN_MMU_FTR_SECTION
srwi r10, r13, 12 /* grab RPN[12:31] */
mtspr SPRN_MAS7, r10
END_MMU_FTR_SECTION_IFSET(MMU_FTR_BIG_PHYS)
#else
li r10, (_PAGE_EXEC | _PAGE_PRESENT)
rlwimi r10, r11, 31, 29, 29 /* extract _PAGE_DIRTY into SW */
and r12, r11, r10
andi. r10, r11, _PAGE_USER /* Test for _PAGE_USER */
slwi r10, r12, 1
or r10, r10, r12
iseleq r12, r12, r10
rlwimi r11, r12, 0, 20, 31 /* Extract RPN from PTE and merge with perms */
mtspr SPRN_MAS3, r11
#endif
#ifdef CONFIG_E200
/* Round robin TLB1 entries assignment */
mfspr r12, SPRN_MAS0
/* Extract TLB1CFG(NENTRY) */
mfspr r11, SPRN_TLB1CFG
andi. r11, r11, 0xfff
/* Extract MAS0(NV) */
andi. r13, r12, 0xfff
addi r13, r13, 1
cmpw 0, r13, r11
addi r12, r12, 1
/* check if we need to wrap */
blt 7f
/* wrap back to first free tlbcam entry */
lis r13, tlbcam_index@ha
lwz r13, tlbcam_index@l(r13)
rlwimi r12, r13, 0, 20, 31
7:
mtspr SPRN_MAS0,r12
#endif /* CONFIG_E200 */
tlbwe
/* Done...restore registers and get out of here. */
mfspr r11, SPRN_SPRG_RSCRATCH4
mtcr r11
mfspr r13, SPRN_SPRG_RSCRATCH3
mfspr r12, SPRN_SPRG_RSCRATCH2
mfspr r11, SPRN_SPRG_RSCRATCH1
mfspr r10, SPRN_SPRG_RSCRATCH0
rfi /* Force context change */
#ifdef CONFIG_SPE
/* Note that the SPE support is closely modeled after the AltiVec
* support. Changes to one are likely to be applicable to the
* other! */
load_up_spe:
/*
* Disable SPE for the task which had SPE previously,
* and save its SPE registers in its thread_struct.
* Enables SPE for use in the kernel on return.
* On SMP we know the SPE units are free, since we give it up every
* switch. -- Kumar
*/
mfmsr r5
oris r5,r5,MSR_SPE@h
mtmsr r5 /* enable use of SPE now */
isync
/*
* For SMP, we don't do lazy SPE switching because it just gets too
* horrendously complex, especially when a task switches from one CPU
* to another. Instead we call giveup_spe in switch_to.
*/
#ifndef CONFIG_SMP
lis r3,last_task_used_spe@ha
lwz r4,last_task_used_spe@l(r3)
cmpi 0,r4,0
beq 1f
addi r4,r4,THREAD /* want THREAD of last_task_used_spe */
SAVE_32EVRS(0,r10,r4)
evxor evr10, evr10, evr10 /* clear out evr10 */
evmwumiaa evr10, evr10, evr10 /* evr10 <- ACC = 0 * 0 + ACC */
li r5,THREAD_ACC
evstddx evr10, r4, r5 /* save off accumulator */
lwz r5,PT_REGS(r4)
lwz r4,_MSR-STACK_FRAME_OVERHEAD(r5)
lis r10,MSR_SPE@h
andc r4,r4,r10 /* disable SPE for previous task */
stw r4,_MSR-STACK_FRAME_OVERHEAD(r5)
1:
#endif /* !CONFIG_SMP */
/* enable use of SPE after return */
oris r9,r9,MSR_SPE@h
mfspr r5,SPRN_SPRG_THREAD /* current task's THREAD (phys) */
li r4,1
li r10,THREAD_ACC
stw r4,THREAD_USED_SPE(r5)
evlddx evr4,r10,r5
evmra evr4,evr4
REST_32EVRS(0,r10,r5)
#ifndef CONFIG_SMP
subi r4,r5,THREAD
stw r4,last_task_used_spe@l(r3)
#endif /* !CONFIG_SMP */
/* restore registers and return */
2: REST_4GPRS(3, r11)
lwz r10,_CCR(r11)
REST_GPR(1, r11)
mtcr r10
lwz r10,_LINK(r11)
mtlr r10
REST_GPR(10, r11)
mtspr SPRN_SRR1,r9
mtspr SPRN_SRR0,r12
REST_GPR(9, r11)
REST_GPR(12, r11)
lwz r11,GPR11(r11)
rfi
/*
* SPE unavailable trap from kernel - print a message, but let
* the task use SPE in the kernel until it returns to user mode.
*/
KernelSPE:
lwz r3,_MSR(r1)
oris r3,r3,MSR_SPE@h
stw r3,_MSR(r1) /* enable use of SPE after return */
lis r3,87f@h
ori r3,r3,87f@l
mr r4,r2 /* current */
lwz r5,_NIP(r1)
bl printk
b ret_from_except
87: .string "SPE used in kernel (task=%p, pc=%x) \n"
.align 4,0
#endif /* CONFIG_SPE */
/*
* Global functions
*/
/* Adjust or setup IVORs for e200 */
_GLOBAL(__setup_e200_ivors)
li r3,DebugDebug@l
mtspr SPRN_IVOR15,r3
li r3,SPEUnavailable@l
mtspr SPRN_IVOR32,r3
li r3,SPEFloatingPointData@l
mtspr SPRN_IVOR33,r3
li r3,SPEFloatingPointRound@l
mtspr SPRN_IVOR34,r3
sync
blr
/* Adjust or setup IVORs for e500v1/v2 */
_GLOBAL(__setup_e500_ivors)
li r3,DebugCrit@l
mtspr SPRN_IVOR15,r3
li r3,SPEUnavailable@l
mtspr SPRN_IVOR32,r3
li r3,SPEFloatingPointData@l
mtspr SPRN_IVOR33,r3
li r3,SPEFloatingPointRound@l
mtspr SPRN_IVOR34,r3
li r3,PerformanceMonitor@l
mtspr SPRN_IVOR35,r3
sync
blr
/* Adjust or setup IVORs for e500mc */
_GLOBAL(__setup_e500mc_ivors)
li r3,DebugDebug@l
mtspr SPRN_IVOR15,r3
li r3,PerformanceMonitor@l
mtspr SPRN_IVOR35,r3
li r3,Doorbell@l
mtspr SPRN_IVOR36,r3
li r3,CriticalDoorbell@l
mtspr SPRN_IVOR37,r3
sync
blr
/*
* extern void giveup_altivec(struct task_struct *prev)
*
* The e500 core does not have an AltiVec unit.
*/
_GLOBAL(giveup_altivec)
blr
#ifdef CONFIG_SPE
/*
* extern void giveup_spe(struct task_struct *prev)
*
*/
_GLOBAL(giveup_spe)
mfmsr r5
oris r5,r5,MSR_SPE@h
mtmsr r5 /* enable use of SPE now */
isync
cmpi 0,r3,0
beqlr- /* if no previous owner, done */
addi r3,r3,THREAD /* want THREAD of task */
lwz r5,PT_REGS(r3)
cmpi 0,r5,0
SAVE_32EVRS(0, r4, r3)
evxor evr6, evr6, evr6 /* clear out evr6 */
evmwumiaa evr6, evr6, evr6 /* evr6 <- ACC = 0 * 0 + ACC */
li r4,THREAD_ACC
evstddx evr6, r4, r3 /* save off accumulator */
mfspr r6,SPRN_SPEFSCR
stw r6,THREAD_SPEFSCR(r3) /* save spefscr register value */
beq 1f
lwz r4,_MSR-STACK_FRAME_OVERHEAD(r5)
lis r3,MSR_SPE@h
andc r4,r4,r3 /* disable SPE for previous task */
stw r4,_MSR-STACK_FRAME_OVERHEAD(r5)
1:
#ifndef CONFIG_SMP
li r5,0
lis r4,last_task_used_spe@ha
stw r5,last_task_used_spe@l(r4)
#endif /* !CONFIG_SMP */
blr
#endif /* CONFIG_SPE */
/*
* extern void giveup_fpu(struct task_struct *prev)
*
* Not all FSL Book-E cores have an FPU
*/
#ifndef CONFIG_PPC_FPU
_GLOBAL(giveup_fpu)
blr
#endif
/*
* extern void abort(void)
*
* At present, this routine just applies a system reset.
*/
_GLOBAL(abort)
li r13,0
mtspr SPRN_DBCR0,r13 /* disable all debug events */
isync
mfmsr r13
ori r13,r13,MSR_DE@l /* Enable Debug Events */
mtmsr r13
isync
mfspr r13,SPRN_DBCR0
lis r13,(DBCR0_IDM|DBCR0_RST_CHIP)@h
mtspr SPRN_DBCR0,r13
isync
_GLOBAL(set_context)
#ifdef CONFIG_BDI_SWITCH
/* Context switch the PTE pointer for the Abatron BDI2000.
* The PGDIR is the second parameter.
*/
lis r5, abatron_pteptrs@h
ori r5, r5, abatron_pteptrs@l
stw r4, 0x4(r5)
#endif
mtspr SPRN_PID,r3
isync /* Force context change */
blr
_GLOBAL(flush_dcache_L1)
mfspr r3,SPRN_L1CFG0
rlwinm r5,r3,9,3 /* Extract cache block size */
twlgti r5,1 /* Only 32 and 64 byte cache blocks
* are currently defined.
*/
li r4,32
subfic r6,r5,2 /* r6 = log2(1KiB / cache block size) -
* log2(number of ways)
*/
slw r5,r4,r5 /* r5 = cache block size */
rlwinm r7,r3,0,0xff /* Extract number of KiB in the cache */
mulli r7,r7,13 /* An 8-way cache will require 13
* loads per set.
*/
slw r7,r7,r6
/* save off HID0 and set DCFA */
mfspr r8,SPRN_HID0
ori r9,r8,HID0_DCFA@l
mtspr SPRN_HID0,r9
isync
lis r4,KERNELBASE@h
mtctr r7
1: lwz r3,0(r4) /* Load... */
add r4,r4,r5
bdnz 1b
msync
lis r4,KERNELBASE@h
mtctr r7
1: dcbf 0,r4 /* ...and flush. */
add r4,r4,r5
bdnz 1b
/* restore HID0 */
mtspr SPRN_HID0,r8
isync
blr
#ifdef CONFIG_SMP
/* When we get here, r24 needs to hold the CPU # */
.globl __secondary_start
__secondary_start:
lis r3,__secondary_hold_acknowledge@h
ori r3,r3,__secondary_hold_acknowledge@l
stw r24,0(r3)
li r3,0
mr r4,r24 /* Why? */
bl call_setup_cpu
lis r3,tlbcam_index@ha
lwz r3,tlbcam_index@l(r3)
mtctr r3
li r26,0 /* r26 safe? */
/* Load each CAM entry */
1: mr r3,r26
bl loadcam_entry
addi r26,r26,1
bdnz 1b
/* get current_thread_info and current */
lis r1,secondary_ti@ha
lwz r1,secondary_ti@l(r1)
lwz r2,TI_TASK(r1)
/* stack */
addi r1,r1,THREAD_SIZE-STACK_FRAME_OVERHEAD
li r0,0
stw r0,0(r1)
/* ptr to current thread */
addi r4,r2,THREAD /* address of our thread_struct */
mtspr SPRN_SPRG_THREAD,r4
/* Setup the defaults for TLB entries */
li r4,(MAS4_TSIZED(BOOK3E_PAGESZ_4K))@l
mtspr SPRN_MAS4,r4
/* Jump to start_secondary */
lis r4,MSR_KERNEL@h
ori r4,r4,MSR_KERNEL@l
lis r3,start_secondary@h
ori r3,r3,start_secondary@l
mtspr SPRN_SRR0,r3
mtspr SPRN_SRR1,r4
sync
rfi
sync
.globl __secondary_hold_acknowledge
__secondary_hold_acknowledge:
.long -1
#endif
/*
* We put a few things here that have to be page-aligned. This stuff
* goes at the beginning of the data segment, which is page-aligned.
*/
.data
.align 12
.globl sdata
sdata:
.globl empty_zero_page
empty_zero_page:
.space 4096
.globl swapper_pg_dir
swapper_pg_dir:
.space PGD_TABLE_SIZE
/*
* Room for two PTE pointers, usually the kernel and current user pointers
* to their respective root page table.
*/
abatron_pteptrs:
.space 8