Linux-2.6.33.2/drivers/char/ip2/i2cmd.c
/*******************************************************************************
*
* (c) 1998 by Computone Corporation
*
********************************************************************************
*
*
* PACKAGE: Linux tty Device Driver for IntelliPort family of multiport
* serial I/O controllers.
*
* DESCRIPTION: Definition table for In-line and Bypass commands. Applicable
* only when the standard loadware is active. (This is included
* source code, not a separate compilation module.)
*
*******************************************************************************/
//------------------------------------------------------------------------------
//
// Revision History:
//
// 10 October 1991 MAG First Draft
// 7 November 1991 MAG Reflects additional commands.
// 24 February 1992 MAG Additional commands for 1.4.x loadware
// 11 March 1992 MAG Additional commands
// 30 March 1992 MAG Additional command: CMD_DSS_NOW
// 18 May 1992 MAG Discovered commands 39 & 40 must be at the end of a
// packet: affects implementation.
//------------------------------------------------------------------------------
//************
//* Includes *
//************
#include "i2cmd.h" /* To get some bit-defines */
//------------------------------------------------------------------------------
// Here is the table of global arrays which represent each type of command
// supported in the IntelliPort standard loadware. See also i2cmd.h
// for a more complete explanation of what is going on.
//------------------------------------------------------------------------------
// Here are the various globals: note that the names are not used except through
// the macros defined in i2cmd.h. Also note that although they are character
// arrays here (for extendability) they are cast to structure pointers in the
// i2cmd.h macros. See i2cmd.h for flags definitions.
// Length Flags Command
static UCHAR ct02[] = { 1, BTH, 0x02 }; // DTR UP
static UCHAR ct03[] = { 1, BTH, 0x03 }; // DTR DN
static UCHAR ct04[] = { 1, BTH, 0x04 }; // RTS UP
static UCHAR ct05[] = { 1, BTH, 0x05 }; // RTS DN
static UCHAR ct06[] = { 1, BYP, 0x06 }; // START FL
static UCHAR ct07[] = { 2, BTH, 0x07,0 }; // BAUD
static UCHAR ct08[] = { 2, BTH, 0x08,0 }; // BITS
static UCHAR ct09[] = { 2, BTH, 0x09,0 }; // STOP
static UCHAR ct10[] = { 2, BTH, 0x0A,0 }; // PARITY
static UCHAR ct11[] = { 2, BTH, 0x0B,0 }; // XON
static UCHAR ct12[] = { 2, BTH, 0x0C,0 }; // XOFF
static UCHAR ct13[] = { 1, BTH, 0x0D }; // STOP FL
static UCHAR ct14[] = { 1, BYP|VIP, 0x0E }; // ACK HOTK
//static UCHAR ct15[]={ 2, BTH|VIP, 0x0F,0 }; // IRQ SET
static UCHAR ct16[] = { 2, INL, 0x10,0 }; // IXONOPTS
static UCHAR ct17[] = { 2, INL, 0x11,0 }; // OXONOPTS
static UCHAR ct18[] = { 1, INL, 0x12 }; // CTSENAB
static UCHAR ct19[] = { 1, BTH, 0x13 }; // CTSDSAB
static UCHAR ct20[] = { 1, INL, 0x14 }; // DCDENAB
static UCHAR ct21[] = { 1, BTH, 0x15 }; // DCDDSAB
static UCHAR ct22[] = { 1, BTH, 0x16 }; // DSRENAB
static UCHAR ct23[] = { 1, BTH, 0x17 }; // DSRDSAB
static UCHAR ct24[] = { 1, BTH, 0x18 }; // RIENAB
static UCHAR ct25[] = { 1, BTH, 0x19 }; // RIDSAB
static UCHAR ct26[] = { 2, BTH, 0x1A,0 }; // BRKENAB
static UCHAR ct27[] = { 1, BTH, 0x1B }; // BRKDSAB
//static UCHAR ct28[]={ 2, BTH, 0x1C,0 }; // MAXBLOKSIZE
//static UCHAR ct29[]={ 2, 0, 0x1D,0 }; // reserved
static UCHAR ct30[] = { 1, INL, 0x1E }; // CTSFLOWENAB
static UCHAR ct31[] = { 1, INL, 0x1F }; // CTSFLOWDSAB
static UCHAR ct32[] = { 1, INL, 0x20 }; // RTSFLOWENAB
static UCHAR ct33[] = { 1, INL, 0x21 }; // RTSFLOWDSAB
static UCHAR ct34[] = { 2, BTH, 0x22,0 }; // ISTRIPMODE
static UCHAR ct35[] = { 2, BTH|END, 0x23,0 }; // SENDBREAK
static UCHAR ct36[] = { 2, BTH, 0x24,0 }; // SETERRMODE
//static UCHAR ct36a[]={ 3, INL, 0x24,0,0 }; // SET_REPLACE
// The following is listed for completeness, but should never be sent directly
// by user-level code. It is sent only by library routines in response to data
// movement.
//static UCHAR ct37[]={ 5, BYP|VIP, 0x25,0,0,0,0 }; // FLOW PACKET
// Back to normal
//static UCHAR ct38[] = {11, BTH|VAR, 0x26,0,0,0,0,0,0,0,0,0,0 }; // DEF KEY SEQ
//static UCHAR ct39[]={ 3, BTH|END, 0x27,0,0 }; // OPOSTON
//static UCHAR ct40[]={ 1, BTH|END, 0x28 }; // OPOSTOFF
static UCHAR ct41[] = { 1, BYP, 0x29 }; // RESUME
//static UCHAR ct42[]={ 2, BTH, 0x2A,0 }; // TXBAUD
//static UCHAR ct43[]={ 2, BTH, 0x2B,0 }; // RXBAUD
//static UCHAR ct44[]={ 2, BTH, 0x2C,0 }; // MS PING
//static UCHAR ct45[]={ 1, BTH, 0x2D }; // HOTENAB
//static UCHAR ct46[]={ 1, BTH, 0x2E }; // HOTDSAB
//static UCHAR ct47[]={ 7, BTH, 0x2F,0,0,0,0,0,0 }; // UNIX FLAGS
//static UCHAR ct48[]={ 1, BTH, 0x30 }; // DSRFLOWENAB
//static UCHAR ct49[]={ 1, BTH, 0x31 }; // DSRFLOWDSAB
//static UCHAR ct50[]={ 1, BTH, 0x32 }; // DTRFLOWENAB
//static UCHAR ct51[]={ 1, BTH, 0x33 }; // DTRFLOWDSAB
//static UCHAR ct52[]={ 1, BTH, 0x34 }; // BAUDTABRESET
//static UCHAR ct53[] = { 3, BTH, 0x35,0,0 }; // BAUDREMAP
static UCHAR ct54[] = { 3, BTH, 0x36,0,0 }; // CUSTOMBAUD1
static UCHAR ct55[] = { 3, BTH, 0x37,0,0 }; // CUSTOMBAUD2
static UCHAR ct56[] = { 2, BTH|END, 0x38,0 }; // PAUSE
static UCHAR ct57[] = { 1, BYP, 0x39 }; // SUSPEND
static UCHAR ct58[] = { 1, BYP, 0x3A }; // UNSUSPEND
static UCHAR ct59[] = { 2, BTH, 0x3B,0 }; // PARITYCHK
static UCHAR ct60[] = { 1, INL|VIP, 0x3C }; // BOOKMARKREQ
//static UCHAR ct61[]={ 2, BTH, 0x3D,0 }; // INTERNALLOOP
//static UCHAR ct62[]={ 2, BTH, 0x3E,0 }; // HOTKTIMEOUT
static UCHAR ct63[] = { 2, INL, 0x3F,0 }; // SETTXON
static UCHAR ct64[] = { 2, INL, 0x40,0 }; // SETTXOFF
//static UCHAR ct65[]={ 2, BTH, 0x41,0 }; // SETAUTORTS
//static UCHAR ct66[]={ 2, BTH, 0x42,0 }; // SETHIGHWAT
//static UCHAR ct67[]={ 2, BYP, 0x43,0 }; // STARTSELFL
//static UCHAR ct68[]={ 2, INL, 0x44,0 }; // ENDSELFL
//static UCHAR ct69[]={ 1, BYP, 0x45 }; // HWFLOW_OFF
//static UCHAR ct70[]={ 1, BTH, 0x46 }; // ODSRFL_ENAB
//static UCHAR ct71[]={ 1, BTH, 0x47 }; // ODSRFL_DSAB
//static UCHAR ct72[]={ 1, BTH, 0x48 }; // ODCDFL_ENAB
//static UCHAR ct73[]={ 1, BTH, 0x49 }; // ODCDFL_DSAB
//static UCHAR ct74[]={ 2, BTH, 0x4A,0 }; // LOADLEVEL
//static UCHAR ct75[]={ 2, BTH, 0x4B,0 }; // STATDATA
//static UCHAR ct76[]={ 1, BYP, 0x4C }; // BREAK_ON
//static UCHAR ct77[]={ 1, BYP, 0x4D }; // BREAK_OFF
//static UCHAR ct78[]={ 1, BYP, 0x4E }; // GETFC
static UCHAR ct79[] = { 2, BYP, 0x4F,0 }; // XMIT_NOW
//static UCHAR ct80[]={ 4, BTH, 0x50,0,0,0 }; // DIVISOR_LATCH
//static UCHAR ct81[]={ 1, BYP, 0x51 }; // GET_STATUS
//static UCHAR ct82[]={ 1, BYP, 0x52 }; // GET_TXCNT
//static UCHAR ct83[]={ 1, BYP, 0x53 }; // GET_RXCNT
//static UCHAR ct84[]={ 1, BYP, 0x54 }; // GET_BOXIDS
//static UCHAR ct85[]={10, BYP, 0x55,0,0,0,0,0,0,0,0,0 }; // ENAB_MULT
//static UCHAR ct86[]={ 2, BTH, 0x56,0 }; // RCV_ENABLE
static UCHAR ct87[] = { 1, BYP, 0x57 }; // HW_TEST
//static UCHAR ct88[]={ 3, BTH, 0x58,0,0 }; // RCV_THRESHOLD
//static UCHAR ct90[]={ 3, BYP, 0x5A,0,0 }; // Set SILO
//static UCHAR ct91[]={ 2, BYP, 0x5B,0 }; // timed break
// Some composite commands as well
//static UCHAR cc01[]={ 2, BTH, 0x02,0x04 }; // DTR & RTS UP
//static UCHAR cc02[]={ 2, BTH, 0x03,0x05 }; // DTR & RTS DN
//********
//* Code *
//********
//******************************************************************************
// Function: i2cmdUnixFlags(iflag, cflag, lflag)
// Parameters: Unix tty flags
//
// Returns: Pointer to command structure
//
// Description:
//
// This routine sets the parameters of command 47 and returns a pointer to the
// appropriate structure.
//******************************************************************************
#if 0
cmdSyntaxPtr
i2cmdUnixFlags(unsigned short iflag,unsigned short cflag,unsigned short lflag)
{
cmdSyntaxPtr pCM = (cmdSyntaxPtr) ct47;
pCM->cmd[1] = (unsigned char) iflag;
pCM->cmd[2] = (unsigned char) (iflag >> 8);
pCM->cmd[3] = (unsigned char) cflag;
pCM->cmd[4] = (unsigned char) (cflag >> 8);
pCM->cmd[5] = (unsigned char) lflag;
pCM->cmd[6] = (unsigned char) (lflag >> 8);
return pCM;
}
#endif /* 0 */
//******************************************************************************
// Function: i2cmdBaudDef(which, rate)
// Parameters: ?
//
// Returns: Pointer to command structure
//
// Description:
//
// This routine sets the parameters of commands 54 or 55 (according to the
// argument which), and returns a pointer to the appropriate structure.
//******************************************************************************
static cmdSyntaxPtr
i2cmdBaudDef(int which, unsigned short rate)
{
cmdSyntaxPtr pCM;
switch(which)
{
case 1:
pCM = (cmdSyntaxPtr) ct54;
break;
default:
case 2:
pCM = (cmdSyntaxPtr) ct55;
break;
}
pCM->cmd[1] = (unsigned char) rate;
pCM->cmd[2] = (unsigned char) (rate >> 8);
return pCM;
}