Linux-2.6.33.2/drivers/usb/serial/cp210x.c
/*
* Silicon Laboratories CP210x USB to RS232 serial adaptor driver
*
* Copyright (C) 2005 Craig Shelley (craig@microtron.org.uk)
*
* This program is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public License version
* 2 as published by the Free Software Foundation.
*
* Support to set flow control line levels using TIOCMGET and TIOCMSET
* thanks to Karl Hiramoto karl@hiramoto.org. RTSCTS hardware flow
* control thanks to Munir Nassar nassarmu@real-time.com
*
*/
#include <linux/kernel.h>
#include <linux/errno.h>
#include <linux/slab.h>
#include <linux/tty.h>
#include <linux/tty_flip.h>
#include <linux/module.h>
#include <linux/moduleparam.h>
#include <linux/usb.h>
#include <linux/uaccess.h>
#include <linux/usb/serial.h>
/*
* Version Information
*/
#define DRIVER_VERSION "v0.09"
#define DRIVER_DESC "Silicon Labs CP210x RS232 serial adaptor driver"
/*
* Function Prototypes
*/
static int cp210x_open(struct tty_struct *tty, struct usb_serial_port *);
static void cp210x_cleanup(struct usb_serial_port *);
static void cp210x_close(struct usb_serial_port *);
static void cp210x_get_termios(struct tty_struct *,
struct usb_serial_port *port);
static void cp210x_get_termios_port(struct usb_serial_port *port,
unsigned int *cflagp, unsigned int *baudp);
static void cp210x_set_termios(struct tty_struct *, struct usb_serial_port *,
struct ktermios*);
static int cp210x_tiocmget(struct tty_struct *, struct file *);
static int cp210x_tiocmset(struct tty_struct *, struct file *,
unsigned int, unsigned int);
static int cp210x_tiocmset_port(struct usb_serial_port *port, struct file *,
unsigned int, unsigned int);
static void cp210x_break_ctl(struct tty_struct *, int);
static int cp210x_startup(struct usb_serial *);
static void cp210x_disconnect(struct usb_serial *);
static void cp210x_dtr_rts(struct usb_serial_port *p, int on);
static int cp210x_carrier_raised(struct usb_serial_port *p);
static int debug;
static struct usb_device_id id_table [] = {
{ USB_DEVICE(0x0471, 0x066A) }, /* AKTAKOM ACE-1001 cable */
{ USB_DEVICE(0x0489, 0xE000) }, /* Pirelli Broadband S.p.A, DP-L10 SIP/GSM Mobile */
{ USB_DEVICE(0x0745, 0x1000) }, /* CipherLab USB CCD Barcode Scanner 1000 */
{ USB_DEVICE(0x08e6, 0x5501) }, /* Gemalto Prox-PU/CU contactless smartcard reader */
{ USB_DEVICE(0x08FD, 0x000A) }, /* Digianswer A/S , ZigBee/802.15.4 MAC Device */
{ USB_DEVICE(0x0FCF, 0x1003) }, /* Dynastream ANT development board */
{ USB_DEVICE(0x0FCF, 0x1004) }, /* Dynastream ANT2USB */
{ USB_DEVICE(0x0FCF, 0x1006) }, /* Dynastream ANT development board */
{ USB_DEVICE(0x10A6, 0xAA26) }, /* Knock-off DCU-11 cable */
{ USB_DEVICE(0x10AB, 0x10C5) }, /* Siemens MC60 Cable */
{ USB_DEVICE(0x10B5, 0xAC70) }, /* Nokia CA-42 USB */
{ USB_DEVICE(0x10C4, 0x0F91) }, /* Vstabi */
{ USB_DEVICE(0x10C4, 0x1101) }, /* Arkham Technology DS101 Bus Monitor */
{ USB_DEVICE(0x10C4, 0x1601) }, /* Arkham Technology DS101 Adapter */
{ USB_DEVICE(0x10C4, 0x800A) }, /* SPORTident BSM7-D-USB main station */
{ USB_DEVICE(0x10C4, 0x803B) }, /* Pololu USB-serial converter */
{ USB_DEVICE(0x10C4, 0x8053) }, /* Enfora EDG1228 */
{ USB_DEVICE(0x10C4, 0x8054) }, /* Enfora GSM2228 */
{ USB_DEVICE(0x10C4, 0x8066) }, /* Argussoft In-System Programmer */
{ USB_DEVICE(0x10C4, 0x807A) }, /* Crumb128 board */
{ USB_DEVICE(0x10C4, 0x80CA) }, /* Degree Controls Inc */
{ USB_DEVICE(0x10C4, 0x80DD) }, /* Tracient RFID */
{ USB_DEVICE(0x10C4, 0x80F6) }, /* Suunto sports instrument */
{ USB_DEVICE(0x10C4, 0x8115) }, /* Arygon NFC/Mifare Reader */
{ USB_DEVICE(0x10C4, 0x813D) }, /* Burnside Telecom Deskmobile */
{ USB_DEVICE(0x10C4, 0x813F) }, /* Tams Master Easy Control */
{ USB_DEVICE(0x10C4, 0x814A) }, /* West Mountain Radio RIGblaster P&P */
{ USB_DEVICE(0x10C4, 0x814B) }, /* West Mountain Radio RIGtalk */
{ USB_DEVICE(0x10C4, 0x815E) }, /* Helicomm IP-Link 1220-DVM */
{ USB_DEVICE(0x10C4, 0x819F) }, /* MJS USB Toslink Switcher */
{ USB_DEVICE(0x10C4, 0x81A6) }, /* ThinkOptics WavIt */
{ USB_DEVICE(0x10C4, 0x81AC) }, /* MSD Dash Hawk */
{ USB_DEVICE(0x10C4, 0x81C8) }, /* Lipowsky Industrie Elektronik GmbH, Baby-JTAG */
{ USB_DEVICE(0x10C4, 0x81E2) }, /* Lipowsky Industrie Elektronik GmbH, Baby-LIN */
{ USB_DEVICE(0x10C4, 0x81E7) }, /* Aerocomm Radio */
{ USB_DEVICE(0x10C4, 0x81E8) }, /* Zephyr Bioharness */
{ USB_DEVICE(0x10C4, 0x81F2) }, /* C1007 HF band RFID controller */
{ USB_DEVICE(0x10C4, 0x8218) }, /* Lipowsky Industrie Elektronik GmbH, HARP-1 */
{ USB_DEVICE(0x10C4, 0x822B) }, /* Modem EDGE(GSM) Comander 2 */
{ USB_DEVICE(0x10C4, 0x826B) }, /* Cygnal Integrated Products, Inc., Fasttrax GPS demostration module */
{ USB_DEVICE(0x10C4, 0x8293) }, /* Telegesys ETRX2USB */
{ USB_DEVICE(0x10C4, 0x82F9) }, /* Procyon AVS */
{ USB_DEVICE(0x10C4, 0x8341) }, /* Siemens MC35PU GPRS Modem */
{ USB_DEVICE(0x10C4, 0x8382) }, /* Cygnal Integrated Products, Inc. */
{ USB_DEVICE(0x10C4, 0x83A8) }, /* Amber Wireless AMB2560 */
{ USB_DEVICE(0x10C4, 0x8411) }, /* Kyocera GPS Module */
{ USB_DEVICE(0x10C4, 0x846E) }, /* BEI USB Sensor Interface (VCP) */
{ USB_DEVICE(0x10C4, 0xEA60) }, /* Silicon Labs factory default */
{ USB_DEVICE(0x10C4, 0xEA61) }, /* Silicon Labs factory default */
{ USB_DEVICE(0x10C4, 0xF001) }, /* Elan Digital Systems USBscope50 */
{ USB_DEVICE(0x10C4, 0xF002) }, /* Elan Digital Systems USBwave12 */
{ USB_DEVICE(0x10C4, 0xF003) }, /* Elan Digital Systems USBpulse100 */
{ USB_DEVICE(0x10C4, 0xF004) }, /* Elan Digital Systems USBcount50 */
{ USB_DEVICE(0x10C5, 0xEA61) }, /* Silicon Labs MobiData GPRS USB Modem */
{ USB_DEVICE(0x10CE, 0xEA6A) }, /* Silicon Labs MobiData GPRS USB Modem 100EU */
{ USB_DEVICE(0x13AD, 0x9999) }, /* Baltech card reader */
{ USB_DEVICE(0x1555, 0x0004) }, /* Owen AC4 USB-RS485 Converter */
{ USB_DEVICE(0x166A, 0x0303) }, /* Clipsal 5500PCU C-Bus USB interface */
{ USB_DEVICE(0x16D6, 0x0001) }, /* Jablotron serial interface */
{ USB_DEVICE(0x18EF, 0xE00F) }, /* ELV USB-I2C-Interface */
{ USB_DEVICE(0x413C, 0x9500) }, /* DW700 GPS USB interface */
{ } /* Terminating Entry */
};
MODULE_DEVICE_TABLE(usb, id_table);
static struct usb_driver cp210x_driver = {
.name = "cp210x",
.probe = usb_serial_probe,
.disconnect = usb_serial_disconnect,
.id_table = id_table,
.no_dynamic_id = 1,
};
static struct usb_serial_driver cp210x_device = {
.driver = {
.owner = THIS_MODULE,
.name = "cp210x",
},
.usb_driver = &cp210x_driver,
.id_table = id_table,
.num_ports = 1,
.open = cp210x_open,
.close = cp210x_close,
.break_ctl = cp210x_break_ctl,
.set_termios = cp210x_set_termios,
.tiocmget = cp210x_tiocmget,
.tiocmset = cp210x_tiocmset,
.attach = cp210x_startup,
.disconnect = cp210x_disconnect,
.dtr_rts = cp210x_dtr_rts,
.carrier_raised = cp210x_carrier_raised
};
/* Config request types */
#define REQTYPE_HOST_TO_DEVICE 0x41
#define REQTYPE_DEVICE_TO_HOST 0xc1
/* Config request codes */
#define CP210X_IFC_ENABLE 0x00
#define CP210X_SET_BAUDDIV 0x01
#define CP210X_GET_BAUDDIV 0x02
#define CP210X_SET_LINE_CTL 0x03
#define CP210X_GET_LINE_CTL 0x04
#define CP210X_SET_BREAK 0x05
#define CP210X_IMM_CHAR 0x06
#define CP210X_SET_MHS 0x07
#define CP210X_GET_MDMSTS 0x08
#define CP210X_SET_XON 0x09
#define CP210X_SET_XOFF 0x0A
#define CP210X_SET_EVENTMASK 0x0B
#define CP210X_GET_EVENTMASK 0x0C
#define CP210X_SET_CHAR 0x0D
#define CP210X_GET_CHARS 0x0E
#define CP210X_GET_PROPS 0x0F
#define CP210X_GET_COMM_STATUS 0x10
#define CP210X_RESET 0x11
#define CP210X_PURGE 0x12
#define CP210X_SET_FLOW 0x13
#define CP210X_GET_FLOW 0x14
#define CP210X_EMBED_EVENTS 0x15
#define CP210X_GET_EVENTSTATE 0x16
#define CP210X_SET_CHARS 0x19
/* CP210X_IFC_ENABLE */
#define UART_ENABLE 0x0001
#define UART_DISABLE 0x0000
/* CP210X_(SET|GET)_BAUDDIV */
#define BAUD_RATE_GEN_FREQ 0x384000
/* CP210X_(SET|GET)_LINE_CTL */
#define BITS_DATA_MASK 0X0f00
#define BITS_DATA_5 0X0500
#define BITS_DATA_6 0X0600
#define BITS_DATA_7 0X0700
#define BITS_DATA_8 0X0800
#define BITS_DATA_9 0X0900
#define BITS_PARITY_MASK 0x00f0
#define BITS_PARITY_NONE 0x0000
#define BITS_PARITY_ODD 0x0010
#define BITS_PARITY_EVEN 0x0020
#define BITS_PARITY_MARK 0x0030
#define BITS_PARITY_SPACE 0x0040
#define BITS_STOP_MASK 0x000f
#define BITS_STOP_1 0x0000
#define BITS_STOP_1_5 0x0001
#define BITS_STOP_2 0x0002
/* CP210X_SET_BREAK */
#define BREAK_ON 0x0000
#define BREAK_OFF 0x0001
/* CP210X_(SET_MHS|GET_MDMSTS) */
#define CONTROL_DTR 0x0001
#define CONTROL_RTS 0x0002
#define CONTROL_CTS 0x0010
#define CONTROL_DSR 0x0020
#define CONTROL_RING 0x0040
#define CONTROL_DCD 0x0080
#define CONTROL_WRITE_DTR 0x0100
#define CONTROL_WRITE_RTS 0x0200
/*
* cp210x_get_config
* Reads from the CP210x configuration registers
* 'size' is specified in bytes.
* 'data' is a pointer to a pre-allocated array of integers large
* enough to hold 'size' bytes (with 4 bytes to each integer)
*/
static int cp210x_get_config(struct usb_serial_port *port, u8 request,
unsigned int *data, int size)
{
struct usb_serial *serial = port->serial;
__le32 *buf;
int result, i, length;
/* Number of integers required to contain the array */
length = (((size - 1) | 3) + 1)/4;
buf = kcalloc(length, sizeof(__le32), GFP_KERNEL);
if (!buf) {
dev_err(&port->dev, "%s - out of memory.\n", __func__);
return -ENOMEM;
}
/* Issue the request, attempting to read 'size' bytes */
result = usb_control_msg(serial->dev, usb_rcvctrlpipe(serial->dev, 0),
request, REQTYPE_DEVICE_TO_HOST, 0x0000,
0, buf, size, 300);
/* Convert data into an array of integers */
for (i = 0; i < length; i++)
data[i] = le32_to_cpu(buf[i]);
kfree(buf);
if (result != size) {
dbg("%s - Unable to send config request, "
"request=0x%x size=%d result=%d\n",
__func__, request, size, result);
return -EPROTO;
}
return 0;
}
/*
* cp210x_set_config
* Writes to the CP210x configuration registers
* Values less than 16 bits wide are sent directly
* 'size' is specified in bytes.
*/
static int cp210x_set_config(struct usb_serial_port *port, u8 request,
unsigned int *data, int size)
{
struct usb_serial *serial = port->serial;
__le32 *buf;
int result, i, length;
/* Number of integers required to contain the array */
length = (((size - 1) | 3) + 1)/4;
buf = kmalloc(length * sizeof(__le32), GFP_KERNEL);
if (!buf) {
dev_err(&port->dev, "%s - out of memory.\n",
__func__);
return -ENOMEM;
}
/* Array of integers into bytes */
for (i = 0; i < length; i++)
buf[i] = cpu_to_le32(data[i]);
if (size > 2) {
result = usb_control_msg(serial->dev,
usb_sndctrlpipe(serial->dev, 0),
request, REQTYPE_HOST_TO_DEVICE, 0x0000,
0, buf, size, 300);
} else {
result = usb_control_msg(serial->dev,
usb_sndctrlpipe(serial->dev, 0),
request, REQTYPE_HOST_TO_DEVICE, data[0],
0, NULL, 0, 300);
}
kfree(buf);
if ((size > 2 && result != size) || result < 0) {
dbg("%s - Unable to send request, "
"request=0x%x size=%d result=%d\n",
__func__, request, size, result);
return -EPROTO;
}
/* Single data value */
result = usb_control_msg(serial->dev,
usb_sndctrlpipe(serial->dev, 0),
request, REQTYPE_HOST_TO_DEVICE, data[0],
0, NULL, 0, 300);
return 0;
}
/*
* cp210x_set_config_single
* Convenience function for calling cp210x_set_config on single data values
* without requiring an integer pointer
*/
static inline int cp210x_set_config_single(struct usb_serial_port *port,
u8 request, unsigned int data)
{
return cp210x_set_config(port, request, &data, 2);
}
/*
* cp210x_quantise_baudrate
* Quantises the baud rate as per AN205 Table 1
*/
static unsigned int cp210x_quantise_baudrate(unsigned int baud) {
if (baud <= 56) baud = 0;
else if (baud <= 300) baud = 300;
else if (baud <= 600) baud = 600;
else if (baud <= 1200) baud = 1200;
else if (baud <= 1800) baud = 1800;
else if (baud <= 2400) baud = 2400;
else if (baud <= 4000) baud = 4000;
else if (baud <= 4803) baud = 4800;
else if (baud <= 7207) baud = 7200;
else if (baud <= 9612) baud = 9600;
else if (baud <= 14428) baud = 14400;
else if (baud <= 16062) baud = 16000;
else if (baud <= 19250) baud = 19200;
else if (baud <= 28912) baud = 28800;
else if (baud <= 38601) baud = 38400;
else if (baud <= 51558) baud = 51200;
else if (baud <= 56280) baud = 56000;
else if (baud <= 58053) baud = 57600;
else if (baud <= 64111) baud = 64000;
else if (baud <= 77608) baud = 76800;
else if (baud <= 117028) baud = 115200;
else if (baud <= 129347) baud = 128000;
else if (baud <= 156868) baud = 153600;
else if (baud <= 237832) baud = 230400;
else if (baud <= 254234) baud = 250000;
else if (baud <= 273066) baud = 256000;
else if (baud <= 491520) baud = 460800;
else if (baud <= 567138) baud = 500000;
else if (baud <= 670254) baud = 576000;
else if (baud <= 1053257) baud = 921600;
else if (baud <= 1474560) baud = 1228800;
else if (baud <= 2457600) baud = 1843200;
else baud = 3686400;
return baud;
}
static int cp210x_open(struct tty_struct *tty, struct usb_serial_port *port)
{
struct usb_serial *serial = port->serial;
int result;
dbg("%s - port %d", __func__, port->number);
if (cp210x_set_config_single(port, CP210X_IFC_ENABLE, UART_ENABLE)) {
dev_err(&port->dev, "%s - Unable to enable UART\n",
__func__);
return -EPROTO;
}
/* Start reading from the device */
usb_fill_bulk_urb(port->read_urb, serial->dev,
usb_rcvbulkpipe(serial->dev,
port->bulk_in_endpointAddress),
port->read_urb->transfer_buffer,
port->read_urb->transfer_buffer_length,
serial->type->read_bulk_callback,
port);
result = usb_submit_urb(port->read_urb, GFP_KERNEL);
if (result) {
dev_err(&port->dev, "%s - failed resubmitting read urb, "
"error %d\n", __func__, result);
return result;
}
/* Configure the termios structure */
cp210x_get_termios(tty, port);
return 0;
}
static void cp210x_cleanup(struct usb_serial_port *port)
{
struct usb_serial *serial = port->serial;
dbg("%s - port %d", __func__, port->number);
if (serial->dev) {
/* shutdown any bulk reads that might be going on */
if (serial->num_bulk_out)
usb_kill_urb(port->write_urb);
if (serial->num_bulk_in)
usb_kill_urb(port->read_urb);
}
}
static void cp210x_close(struct usb_serial_port *port)
{
dbg("%s - port %d", __func__, port->number);
/* shutdown our urbs */
dbg("%s - shutting down urbs", __func__);
usb_kill_urb(port->write_urb);
usb_kill_urb(port->read_urb);
mutex_lock(&port->serial->disc_mutex);
if (!port->serial->disconnected)
cp210x_set_config_single(port, CP210X_IFC_ENABLE, UART_DISABLE);
mutex_unlock(&port->serial->disc_mutex);
}
/*
* cp210x_get_termios
* Reads the baud rate, data bits, parity, stop bits and flow control mode
* from the device, corrects any unsupported values, and configures the
* termios structure to reflect the state of the device
*/
static void cp210x_get_termios(struct tty_struct *tty,
struct usb_serial_port *port)
{
unsigned int baud;
if (tty) {
cp210x_get_termios_port(tty->driver_data,
&tty->termios->c_cflag, &baud);
tty_encode_baud_rate(tty, baud, baud);
}
else {
unsigned int cflag;
cflag = 0;
cp210x_get_termios_port(port, &cflag, &baud);
}
}
/*
* cp210x_get_termios_port
* This is the heart of cp210x_get_termios which always uses a &usb_serial_port.
*/
static void cp210x_get_termios_port(struct usb_serial_port *port,
unsigned int *cflagp, unsigned int *baudp)
{
unsigned int cflag, modem_ctl[4];
unsigned int baud;
unsigned int bits;
dbg("%s - port %d", __func__, port->number);
cp210x_get_config(port, CP210X_GET_BAUDDIV, &baud, 2);
/* Convert to baudrate */
if (baud)
baud = cp210x_quantise_baudrate((BAUD_RATE_GEN_FREQ + baud/2)/ baud);
dbg("%s - baud rate = %d", __func__, baud);
*baudp = baud;
cflag = *cflagp;
cp210x_get_config(port, CP210X_GET_LINE_CTL, &bits, 2);
cflag &= ~CSIZE;
switch (bits & BITS_DATA_MASK) {
case BITS_DATA_5:
dbg("%s - data bits = 5", __func__);
cflag |= CS5;
break;
case BITS_DATA_6:
dbg("%s - data bits = 6", __func__);
cflag |= CS6;
break;
case BITS_DATA_7:
dbg("%s - data bits = 7", __func__);
cflag |= CS7;
break;
case BITS_DATA_8:
dbg("%s - data bits = 8", __func__);
cflag |= CS8;
break;
case BITS_DATA_9:
dbg("%s - data bits = 9 (not supported, using 8 data bits)",
__func__);
cflag |= CS8;
bits &= ~BITS_DATA_MASK;
bits |= BITS_DATA_8;
cp210x_set_config(port, CP210X_SET_LINE_CTL, &bits, 2);
break;
default:
dbg("%s - Unknown number of data bits, using 8", __func__);
cflag |= CS8;
bits &= ~BITS_DATA_MASK;
bits |= BITS_DATA_8;
cp210x_set_config(port, CP210X_SET_LINE_CTL, &bits, 2);
break;
}
switch (bits & BITS_PARITY_MASK) {
case BITS_PARITY_NONE:
dbg("%s - parity = NONE", __func__);
cflag &= ~PARENB;
break;
case BITS_PARITY_ODD:
dbg("%s - parity = ODD", __func__);
cflag |= (PARENB|PARODD);
break;
case BITS_PARITY_EVEN:
dbg("%s - parity = EVEN", __func__);
cflag &= ~PARODD;
cflag |= PARENB;
break;
case BITS_PARITY_MARK:
dbg("%s - parity = MARK (not supported, disabling parity)",
__func__);
cflag &= ~PARENB;
bits &= ~BITS_PARITY_MASK;
cp210x_set_config(port, CP210X_SET_LINE_CTL, &bits, 2);
break;
case BITS_PARITY_SPACE:
dbg("%s - parity = SPACE (not supported, disabling parity)",
__func__);
cflag &= ~PARENB;
bits &= ~BITS_PARITY_MASK;
cp210x_set_config(port, CP210X_SET_LINE_CTL, &bits, 2);
break;
default:
dbg("%s - Unknown parity mode, disabling parity", __func__);
cflag &= ~PARENB;
bits &= ~BITS_PARITY_MASK;
cp210x_set_config(port, CP210X_SET_LINE_CTL, &bits, 2);
break;
}
cflag &= ~CSTOPB;
switch (bits & BITS_STOP_MASK) {
case BITS_STOP_1:
dbg("%s - stop bits = 1", __func__);
break;
case BITS_STOP_1_5:
dbg("%s - stop bits = 1.5 (not supported, using 1 stop bit)",
__func__);
bits &= ~BITS_STOP_MASK;
cp210x_set_config(port, CP210X_SET_LINE_CTL, &bits, 2);
break;
case BITS_STOP_2:
dbg("%s - stop bits = 2", __func__);
cflag |= CSTOPB;
break;
default:
dbg("%s - Unknown number of stop bits, using 1 stop bit",
__func__);
bits &= ~BITS_STOP_MASK;
cp210x_set_config(port, CP210X_SET_LINE_CTL, &bits, 2);
break;
}
cp210x_get_config(port, CP210X_GET_FLOW, modem_ctl, 16);
if (modem_ctl[0] & 0x0008) {
dbg("%s - flow control = CRTSCTS", __func__);
cflag |= CRTSCTS;
} else {
dbg("%s - flow control = NONE", __func__);
cflag &= ~CRTSCTS;
}
*cflagp = cflag;
}
static void cp210x_set_termios(struct tty_struct *tty,
struct usb_serial_port *port, struct ktermios *old_termios)
{
unsigned int cflag, old_cflag;
unsigned int baud = 0, bits;
unsigned int modem_ctl[4];
dbg("%s - port %d", __func__, port->number);
if (!tty)
return;
tty->termios->c_cflag &= ~CMSPAR;
cflag = tty->termios->c_cflag;
old_cflag = old_termios->c_cflag;
baud = cp210x_quantise_baudrate(tty_get_baud_rate(tty));
/* If the baud rate is to be updated*/
if (baud != tty_termios_baud_rate(old_termios) && baud != 0) {
dbg("%s - Setting baud rate to %d baud", __func__,
baud);
if (cp210x_set_config_single(port, CP210X_SET_BAUDDIV,
((BAUD_RATE_GEN_FREQ + baud/2) / baud))) {
dbg("Baud rate requested not supported by device\n");
baud = tty_termios_baud_rate(old_termios);
}
}
/* Report back the resulting baud rate */
tty_encode_baud_rate(tty, baud, baud);
/* If the number of data bits is to be updated */
if ((cflag & CSIZE) != (old_cflag & CSIZE)) {
cp210x_get_config(port, CP210X_GET_LINE_CTL, &bits, 2);
bits &= ~BITS_DATA_MASK;
switch (cflag & CSIZE) {
case CS5:
bits |= BITS_DATA_5;
dbg("%s - data bits = 5", __func__);
break;
case CS6:
bits |= BITS_DATA_6;
dbg("%s - data bits = 6", __func__);
break;
case CS7:
bits |= BITS_DATA_7;
dbg("%s - data bits = 7", __func__);
break;
case CS8:
bits |= BITS_DATA_8;
dbg("%s - data bits = 8", __func__);
break;
/*case CS9:
bits |= BITS_DATA_9;
dbg("%s - data bits = 9", __func__);
break;*/
default:
dbg("cp210x driver does not "
"support the number of bits requested,"
" using 8 bit mode\n");
bits |= BITS_DATA_8;
break;
}
if (cp210x_set_config(port, CP210X_SET_LINE_CTL, &bits, 2))
dbg("Number of data bits requested "
"not supported by device\n");
}
if ((cflag & (PARENB|PARODD)) != (old_cflag & (PARENB|PARODD))) {
cp210x_get_config(port, CP210X_GET_LINE_CTL, &bits, 2);
bits &= ~BITS_PARITY_MASK;
if (cflag & PARENB) {
if (cflag & PARODD) {
bits |= BITS_PARITY_ODD;
dbg("%s - parity = ODD", __func__);
} else {
bits |= BITS_PARITY_EVEN;
dbg("%s - parity = EVEN", __func__);
}
}
if (cp210x_set_config(port, CP210X_SET_LINE_CTL, &bits, 2))
dbg("Parity mode not supported "
"by device\n");
}
if ((cflag & CSTOPB) != (old_cflag & CSTOPB)) {
cp210x_get_config(port, CP210X_GET_LINE_CTL, &bits, 2);
bits &= ~BITS_STOP_MASK;
if (cflag & CSTOPB) {
bits |= BITS_STOP_2;
dbg("%s - stop bits = 2", __func__);
} else {
bits |= BITS_STOP_1;
dbg("%s - stop bits = 1", __func__);
}
if (cp210x_set_config(port, CP210X_SET_LINE_CTL, &bits, 2))
dbg("Number of stop bits requested "
"not supported by device\n");
}
if ((cflag & CRTSCTS) != (old_cflag & CRTSCTS)) {
cp210x_get_config(port, CP210X_GET_FLOW, modem_ctl, 16);
dbg("%s - read modem controls = 0x%.4x 0x%.4x 0x%.4x 0x%.4x",
__func__, modem_ctl[0], modem_ctl[1],
modem_ctl[2], modem_ctl[3]);
if (cflag & CRTSCTS) {
modem_ctl[0] &= ~0x7B;
modem_ctl[0] |= 0x09;
modem_ctl[1] = 0x80;
dbg("%s - flow control = CRTSCTS", __func__);
} else {
modem_ctl[0] &= ~0x7B;
modem_ctl[0] |= 0x01;
modem_ctl[1] |= 0x40;
dbg("%s - flow control = NONE", __func__);
}
dbg("%s - write modem controls = 0x%.4x 0x%.4x 0x%.4x 0x%.4x",
__func__, modem_ctl[0], modem_ctl[1],
modem_ctl[2], modem_ctl[3]);
cp210x_set_config(port, CP210X_SET_FLOW, modem_ctl, 16);
}
}
static int cp210x_tiocmset (struct tty_struct *tty, struct file *file,
unsigned int set, unsigned int clear)
{
struct usb_serial_port *port = tty->driver_data;
return cp210x_tiocmset_port(port, file, set, clear);
}
static int cp210x_tiocmset_port(struct usb_serial_port *port, struct file *file,
unsigned int set, unsigned int clear)
{
unsigned int control = 0;
dbg("%s - port %d", __func__, port->number);
if (set & TIOCM_RTS) {
control |= CONTROL_RTS;
control |= CONTROL_WRITE_RTS;
}
if (set & TIOCM_DTR) {
control |= CONTROL_DTR;
control |= CONTROL_WRITE_DTR;
}
if (clear & TIOCM_RTS) {
control &= ~CONTROL_RTS;
control |= CONTROL_WRITE_RTS;
}
if (clear & TIOCM_DTR) {
control &= ~CONTROL_DTR;
control |= CONTROL_WRITE_DTR;
}
dbg("%s - control = 0x%.4x", __func__, control);
return cp210x_set_config(port, CP210X_SET_MHS, &control, 2);
}
static void cp210x_dtr_rts(struct usb_serial_port *p, int on)
{
if (on)
cp210x_tiocmset_port(p, NULL, TIOCM_DTR|TIOCM_RTS, 0);
else
cp210x_tiocmset_port(p, NULL, 0, TIOCM_DTR|TIOCM_RTS);
}
static int cp210x_tiocmget (struct tty_struct *tty, struct file *file)
{
struct usb_serial_port *port = tty->driver_data;
unsigned int control;
int result;
dbg("%s - port %d", __func__, port->number);
cp210x_get_config(port, CP210X_GET_MDMSTS, &control, 1);
result = ((control & CONTROL_DTR) ? TIOCM_DTR : 0)
|((control & CONTROL_RTS) ? TIOCM_RTS : 0)
|((control & CONTROL_CTS) ? TIOCM_CTS : 0)
|((control & CONTROL_DSR) ? TIOCM_DSR : 0)
|((control & CONTROL_RING)? TIOCM_RI : 0)
|((control & CONTROL_DCD) ? TIOCM_CD : 0);
dbg("%s - control = 0x%.2x", __func__, control);
return result;
}
static int cp210x_carrier_raised(struct usb_serial_port *p)
{
unsigned int control;
cp210x_get_config(p, CP210X_GET_MDMSTS, &control, 1);
if (control & CONTROL_DCD)
return 1;
return 0;
}
static void cp210x_break_ctl (struct tty_struct *tty, int break_state)
{
struct usb_serial_port *port = tty->driver_data;
unsigned int state;
dbg("%s - port %d", __func__, port->number);
if (break_state == 0)
state = BREAK_OFF;
else
state = BREAK_ON;
dbg("%s - turning break %s", __func__,
state == BREAK_OFF ? "off" : "on");
cp210x_set_config(port, CP210X_SET_BREAK, &state, 2);
}
static int cp210x_startup(struct usb_serial *serial)
{
/* cp210x buffers behave strangely unless device is reset */
usb_reset_device(serial->dev);
return 0;
}
static void cp210x_disconnect(struct usb_serial *serial)
{
int i;
dbg("%s", __func__);
/* Stop reads and writes on all ports */
for (i = 0; i < serial->num_ports; ++i)
cp210x_cleanup(serial->port[i]);
}
static int __init cp210x_init(void)
{
int retval;
retval = usb_serial_register(&cp210x_device);
if (retval)
return retval; /* Failed to register */
retval = usb_register(&cp210x_driver);
if (retval) {
/* Failed to register */
usb_serial_deregister(&cp210x_device);
return retval;
}
/* Success */
printk(KERN_INFO KBUILD_MODNAME ": " DRIVER_VERSION ":"
DRIVER_DESC "\n");
return 0;
}
static void __exit cp210x_exit(void)
{
usb_deregister(&cp210x_driver);
usb_serial_deregister(&cp210x_device);
}
module_init(cp210x_init);
module_exit(cp210x_exit);
MODULE_DESCRIPTION(DRIVER_DESC);
MODULE_VERSION(DRIVER_VERSION);
MODULE_LICENSE("GPL");
module_param(debug, bool, S_IRUGO | S_IWUSR);
MODULE_PARM_DESC(debug, "Enable verbose debugging messages");