NetBSD-5.0.2/sys/arch/amiga/conf/DRACO
# $NetBSD: DRACO,v 1.127 2008/09/24 17:27:49 tsutsui Exp $
#
# This file was automatically created.
# Changes will be lost when make is run in this directory.
#
# Created from: # NetBSD: GENERIC.in,v 1.69 2008/09/24 17:26:37 tsutsui Exp $
#
# GENERIC machine description file
#
# This machine description file is used to generate the default NetBSD
# kernel. The generic kernel does not include all options, subsystems
# and device drivers, but should be useful for most applications.
#
# The machine description file can be customised for your specific
# machine to reduce the kernel size and improve its performance.
#
# For further information on compiling NetBSD kernels, see the config(8)
# man page.
#
# For further information on hardware support for this architecture, see
# the intro(4) man page. For further information about kernel options
# for this architecture, see the options(4) man page. For an explanation
# of each device driver in this file see the section 4 man page for the
# device.
include "arch/amiga/conf/std.amiga"
options INCLUDE_CONFIG_FILE # embed config file in kernel binary
#ident "GENERIC-$Revision: 1.127 $"
maxusers 8
options RTC_OFFSET=0
#
# mainboards to support (in addition to Amiga)
#
options DRACO
#
# processors this kernel should support
#
options M68060 # support for 060
options M060SP # MC68060 software support (Required for 060)
#
# Networking options
#
options INET # IP networking support (Required)
options INET6 # IPV6
#options IPSEC # IP security
#options IPSEC_ESP # IP security (encryption part; define w/IPSEC)
#options IPSEC_NAT_T # IPsec NAT traversal (NAT-T)
#options IPSEC_DEBUG # debug for IP security
#options GATEWAY # Packet forwarding
#options DIRECTED_BROADCAST # Broadcast across subnets
#options MROUTING # Multicast routing
#options PIM # Protocol Independent Multicast
#options ISO,TPIP # OSI
#options EON # OSI tunneling over IP
options NETATALK # AppleTalk networking protocols
#options TCP_DEBUG # Record last TCP_NDEBUG packets with SO_DEBUG
options PPP_BSDCOMP # BSD-Compress compression support for PPP
options PPP_DEFLATE # Deflate compression support for PPP
options PPP_FILTER # Active filter support for PPP (requires bpf)
options PFIL_HOOKS # pfil(9) packet filter hooks
options IPFILTER_LOG # ipmon(8) log support
options IPFILTER_LOOKUP # ippool(8) support
#options IPFILTER_DEFAULT_BLOCK # block all packets by default
#options ALTQ # Manipulate network interfaces' output queues
#options ALTQ_BLUE # Stochastic Fair Blue
#options ALTQ_CBQ # Class-Based Queueing
#options ALTQ_CDNR # Diffserv Traffic Conditioner
#options ALTQ_FIFOQ # First-In First-Out Queue
#options ALTQ_FLOWVALVE # RED/flow-valve (red-penalty-box)
#options ALTQ_HFSC # Hierarchical Fair Service Curve
#options ALTQ_LOCALQ # Local queueing discipline
#options ALTQ_PRIQ # Priority Queueing
#options ALTQ_RED # Random Early Detection
#options ALTQ_RIO # RED with IN/OUT
#options ALTQ_WFQ # Weighted Fair Queueing
# Filesystems
file-system FFS # Berkeley fast file system
file-system EXT2FS # second extended file system (linux)
#file-system LFS # log-structured filesystem (experimental)
file-system MFS # Memory based filesystem
file-system NFS # Network File System client side code
file-system ADOSFS # AmigaDOS file system
file-system CD9660 # ISO 9660 + Rock Ridge filesystem
file-system MSDOSFS # MS-DOS filesystem
file-system KERNFS # kernel data-structure filesystem
file-system FDESC # user file descriptor filesystem
file-system NULLFS # loopback filesystem
file-system OVERLAY # overlay filesystem
#file-system PORTAL # Portal filesystem
file-system PROCFS # /proc filesystem
file-system UMAPFS # NULLFS + uid and gid remapping
file-system UNION # union filesystem
file-system SMBFS # experimental - CIFS; also needs nsmb (below)
file-system PTYFS # /dev/pts/N support
#file-system TMPFS # Efficient memory file-system
#file-system UDF # experimental - OSTA UDF CD/DVD file-system
# Filesystem options
#options FFS_EI # FFS Endian Independant support
options WAPBL # File system journaling support - Experimental
options QUOTA # User and group quotas in FFS
options SOFTDEP # FFS soft updates support.
#options UFS_DIRHASH # UFS Large Directory Hashing - Experimental
options NFSSERVER # Network File System server side code
#options FFS_NO_SNAPSHOT # No FFS snapshot support
#options EXT2FS_SYSTEM_FLAGS # makes ext2fs file flags (append and
# immutable) behave as system flags.
#
# Compatibility options for various existing systems
#
#options TCP_COMPAT_42 # 4.2BSD TCP/IP bug compat. Not recommended.
options COMPAT_43 # compatibility with 4.3BSD interfaces
options COMPAT_09 # compatibility with NetBSD 0.9
options COMPAT_10 # compatibility with NetBSD 1.0
options COMPAT_12 # compatibility with NetBSD 1.2
options COMPAT_13 # compatibility with NetBSD 1.3
options COMPAT_14 # compatibility with NetBSD 1.4
options COMPAT_15 # compatibility with NetBSD 1.5
options COMPAT_16 # compatibility with NetBSD 1.6
options COMPAT_20 # compatibility with NetBSD 2.0
options COMPAT_30 # NetBSD 3.0 compatibility.
options COMPAT_40 # NetBSD 4.0 compatibility.
options COMPAT_SUNOS # Support to run Sun (m68k) executables
options COMPAT_SVR4 # Support to run SVR4 (m68k) executables
options COMPAT_NOMID # allow nonvalid machine id executables
#options COMPAT_LINUX # Support to run Linux/m68k executables
options EXEC_AOUT # 32-bit aout executables (NetBSD-1.5.x)
options COMPAT_AOUT_M68K # actually make some system calls work.
options COMPAT_BSDPTY # /dev/[pt]ty?? ptys.
#
# Support for System V IPC facilities.
#
options SYSVSHM # System V-like shared memory
options SYSVMSG # System V-like messages
options SYSVSEM # System V-like semaphores
options P1003_1B_SEMAPHORE # p1003.1b semaphore support
#
# Support for various kernel options
#
options KTRACE # system call tracing support
options LKM # Loadable kernel modules
#options INSECURE # disable kernel security levels
options SCSIVERBOSE # human readable SCSI error messages
options USERCONF # userconf(4) support
options NTP # NTP phase/frequency locked loop
#options PIPE_SOCKETPAIR # smaller, but slower pipe(2)
# Enable experimental buffer queue strategy for better responsiveness under
# high disk I/O load. Use it with caution - it's not proven to be stable yet.
#options BUFQ_READPRIO
#options BUFQ_PRIOCSCAN
#
# Misc. debugging options
#
options DDB # Kernel debugger
#options DDB_HISTORY_SIZE=100 # Enable history editing in DDB
#options DIAGNOSTIC # Extra kernel sanity checks
#options DEBUG # Enable misc. kernel debugging code
#options SYSCALL_DEBUG # debug all syscalls.
#options SCSIDEBUG # Add SCSI debugging statements
#options PANICBUTTON # Forced crash via keypress (?)
#
# Amiga specific options
#
#options LIMITMEM=24 # Do not use more than LIMITMEM MB of the
# first bank of RAM. (default: unlimited)
#options NKPTADD=4 # set this for 4 additional KPT pages
#options NKPTADDSHIFT=24 # set this for 1 additional KPT page
# per 16 MB (1<<24 bytes) of RAM
# uncomment and decrease this, or uncomment and
# increase NKPTADD if you get "out of PT pages"
# panics.
# ATTENTION: There is NO WARRANTY AT ALL that the sync will be complete
# before the 10 secondinterval ends, or that KBDRESET does work at all.
#options KBDRESET # sync on Ctrl-Amiga-Amiga
# These options improve performance with the built-in serial port
# on slower Amigas. Try the larger buffers first then lev6_defer.
#options SERIBUF_SIZE=4096
#options SEROBUF_SIZE=32
#options LEV6_DEFER # defers l6 to l4 (below serial l5)
options RETINACONSOLE # enable code to allow retina to be console
#options KFONT_8X11 # 8x11 font
# select a font for the console according to the character set and keymap
# you want to use
options KFONT_CONS_ISO8859_1
#options KFONT_CONS_ISO8859_2
# This is how you would tell the kernel the A2410 oscillator frequencies:
# The used frequencies are the defaults, and do not need option setting
#options ULOWELL_OSC1=36000000
#options ULOWELL_OSC2=66667000
# This is how you specify the blitting speed, higher values may speed up blits
# a littel bit. If you raise this value too much some trash may appear.
# the commented version is the default.
#options RH_MEMCLK=61000000
# this option enables the 64 bit sprite which does not work
# for quite a few people. E.g. The cursor sprite will turn to a block
# when moved to the top of the screen in X.
#options RH_64BIT_SPRITE
# enables fast scroll code appears to now work on 040 systems.
#options RETINA_SPEED_HACK
# enables the Hardwarecursor which does not work on some systems.
#options RH_HARDWARECURSOR
grfrh0 at zbus0 # retina III
grf2 at grfrh0
ite2 at grf2 # terminal emulators for grfs
msc0 at zbus0 # A2232 MSC multiport serial.
mfc0 at zbus0 # MultiFaceCard I/O board
mfcs0 at mfc0 unit 0 # MFC serial
mfcs1 at mfc0 unit 1 # MFC serial
#mfcp0 at mfc0 unit 0 # MFC parallel [not available yet]
#mfc1 at zbus0 # MultiFaceCard 2nd I/O board
#mfcs2 at mfc1 unit 0
#mfcs3 at mfc1 unit 1
#mfcp1 at mfc1 unit 0
hyper* at zbus? # zbus HyperCom3/3+/4/4+
#hyper* at mainbus0 # not yet: HyperCom1 + HyperCom3
com* at hyper? port ? # Hypercom3/4 serial ports
lpt* at hyper? port ? # Hypercom3+/4+ parallel port
#options IOBZCLOCK=22118400 # default, uncomment the next line
#options IOBZCLOCK=24000000 # if needed.
iobl* at zbus? # zbus IOBlix
com* at iobl? port ? # IOBlix serial ports
lpt* at iobl? port ? # IOBlix parallel ports
#
# Keyboard device. Optionally can attach a wskbd.
# wskbd works together with a wsdisplay so enable them both if you will.
# Don't enable wskbd if you use ite.
#
# XXX in std.amiga: kbd0 at mainbus0
#wskbd0 at kbd0 console ?
#wsmouse* at ms?
#
# DraCo Mainboard devices (sans keyboard)
#
drbbc0 at mainbus0 # DraCo battery backed clock
drsupio0 at mainbus0 # DraCo superio chip
com* at drsupio? port ? # DraCo serial
lpt0 at drsupio? port ? # DraCo parallel
#
# Zorro-II, Zorro-III, DraCo Direct-Bus devices (sans graphics)
#
repulse* at zbus0 # ALiENDESiGN Repulse
audio* at repulse?
toccata* at zbus0 # MacroSystem GmbH Toccata
audio* at toccata?
# Ethernet cards:
le* at zbus0 # A2065, Ameristar, Ariadne
ne* at zbus0 # AriadneII, X-surf
ed* at zbus0 # Hydra, ASDG LanRover
es* at zbus0 # CEI A4066 EthernetPLUS
qn* at zbus0 # Quicknet
# Arcnet
bah* at zbus0 # C=/Ameristar A2060 / 560
drsc0 at mainbus0 # DraCo scsi
scsibus* at drsc0
# each hard drive from low target to high
# will configure to the next available sd unit number
sd* at scsibus? target ? lun ? # scsi disks
st* at scsibus? target ? lun ? # scsi tapes
cd* at scsibus? target ? lun ? # scsi cds
ch* at scsibus? target ? lun ? # scsi autochangers
ss* at scsibus? target ? lun ? # scsi scanner
uk* at scsibus? target ? lun ? # scsi unknown
#
# accept filters
pseudo-device accf_data # "dataready" accept filter
pseudo-device accf_http # "httpready" accept filter
pseudo-device loop # loopback network interface
pseudo-device sl # SLIP network interfaces
pseudo-device ppp # PPP network interfaces
pseudo-device pppoe # PPP over Ethernet (RFC 2516)
pseudo-device tun # network tunnel line discipline
pseudo-device tap # virtual Ethernet
#pseudo-device gre # generic L3 over IP tunnel
pseudo-device bpfilter # Berkeley packet filter
#pseudo-device carp # Common Address Redundancy Protocol
pseudo-device ipfilter # IP Filter package
pseudo-device gif # IPv[46] over IPv[46] tunnel (RFC1933)
#pseudo-device faith # IPv[46] tcp relay translation i/f
pseudo-device stf # 6to4 IPv6 over IPv4 encapsulation
pseudo-device vlan # IEEE 802.1q encapsulation
pseudo-device bridge # simple inter-network bridging
#options BRIDGE_IPF # bridge uses IP/IPv6 pfil hooks too
pseudo-device agr # IEEE 802.3ad link aggregation
#pseudo-device pf # PF packet filter
#pseudo-device pflog # PF log if
pseudo-device fss 4 # file system snapshot device
pseudo-device view 4 # views (needed for grfcc)
pseudo-device pty # pseudo-terminals
pseudo-device clockctl # user control of clock subsystem
#pseudo-device wsfont # wsfont(4) dynamic font loading support
#pseudo-device wsmux # mouse & keyboard multiplexor
pseudo-device vnd # vnode pseudo-disks
#options VND_COMPRESSION # compressed vnd(4)
pseudo-device ccd 4 # concatenated disk devices
#pseudo-device cgd 4 # cryptographic disk devices
pseudo-device raid 8 # RAIDframe disk driver
options RAID_AUTOCONFIG # auto-configuration of RAID components
# Options to enable various other RAIDframe RAID types.
# options RF_INCLUDE_EVENODD=1
# options RF_INCLUDE_RAID5_RS=1
# options RF_INCLUDE_PARITYLOGGING=1
# options RF_INCLUDE_CHAINDECLUSTER=1
# options RF_INCLUDE_INTERDECLUSTER=1
# options RF_INCLUDE_PARITY_DECLUSTERING=1
# options RF_INCLUDE_PARITY_DECLUSTERING_DS=1
pseudo-device rnd # /dev/random and in-kernel generator
#options RND_COM # use "com" randomness as well (BROKEN)
pseudo-device ksyms # /dev/ksyms (kernel symbols)
pseudo-device nsmb # experimental - SMB requester
# Veriexec
#
# a pseudo device needed for veriexec
#pseudo-device veriexec 1
#
# Uncomment the fingerprint methods below that are desired. Note that
# removing fingerprint methods will have almost no impact on the kernel
# code size.
#
#options VERIFIED_EXEC_FP_RMD160
#options VERIFIED_EXEC_FP_SHA256
#options VERIFIED_EXEC_FP_SHA384
#options VERIFIED_EXEC_FP_SHA512
#options VERIFIED_EXEC_FP_SHA1
#options VERIFIED_EXEC_FP_MD5
config netbsd root on ? type ?