NetBSD-5.0.2/sys/arch/mvme68k/docs/Interrupts

$NetBSD: Interrupts,v 1.1 2000/12/14 20:30:14 scw Exp $

NetBSD/mvme68k Interrupt Levels
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

NetBSD/mvme68k interrupts are dependent on the type of device which
generates them. This holds true regardless of what bus the device is
situated on (eg. local, VMEbus or IndustryPack site).

On MVME147, there is a fixed 1:1 mapping of VMEbus interrupt level
to CPU interrupt level. This implies that VMEbus devices must be
set to interrupt at the correct level for that type of device.

On the other boards, each VMEbus interrupt level can be mapped to a
specific CPU interrupt level so the above restriction does not apply.
However, note that the mapping can only be done once. Therefore it is
not possible to have two VMEbus devices which require different CPU
interrupt levels sharing the same VMEbus interrupt level.

The mapping of device type to CPU interrupt levels is as follows:

	CPU Irq		Device Type
	~~~~~~~		~~~~~~~~~~~
	<Highest>
	6 - 7		Anything which generates an exceptional condition
			which *must* be responded to immediately. For
			example, a memory parity/uncorrectable data error.

	5		Reserved for the system clock/scheduler. Do not use.

	4		Serial port devices (rs232, rs422 etc).

	3		Network interfaces.

	2		Disk/Block device interfaces.

	1		Anything else.
	<Lowest>



Interrupt Vectors
~~~~~~~~~~~~~~~~~

NetBSD/mvme68k does not use or generate `auto-vectored' interrupts.

All vectored interrupts up to and including vector 0x7f are reserved
for use by onboard devices.

VMEbus cards and IndustryPack modules are free to use vectors 0x80 -> 0xff.

The onboard devices' vectors are as follows:

MVME147:
	0x40		PCC: ACFAIL
	0x41		PCC: BERR
	0x42		PCC: ABORT Switch
	0x43		PCC: ZS Chips shared vector
	0x44		PCC: Lance Ethernet
	0x45		PCC: WD33C93 SCSI
	0x46		PCC: DMA
	0x47		PCC: Printer
	0x48		PCC: Timer1
	0x49		PCC: Timer2
	0x4a		PCC: Soft Interrupt 1
	0x4b		PCC: Soft Interrupt 2
	0x4c -> 0x4f	PCC: <unused>


MVME167/177:
	0x50		PCC2: Printer `BUSY'
	0x51		PCC2: Printer `Paper Empty'
	0x52		PCC2: Printer `Select'
	0x53		PCC2: Printer `Fault'
	0x54		PCC2: Printer `ACK'
	0x55		PCC2: SCSI
	0x56		PCC2: Ethernet `Error'
	0x57		PCC2: Ethernet
	0x58		PCC2: Timer 2
	0x59		PCC2: Timer 1
	0x5a		PCC2: GPIO
	0x5b		PCC2: <unused>
	0x5c		PCC2: CD2401 Rx Exception
	0x5d		PCC2: CD2401 Modem
	0x5e		PCC2: CD2401 Tx
	0x5f		PCC2: CD2401 Rx

	0x60 -> 0x67	VME2: <unused>
	0x68		VME2: Software Interrupt #0
	0x69		VME2: Software Interrupt #1
	0x6a		VME2: Software Interrupt #2
	0x6b		VME2: Software Interrupt #3
	0x6c		VME2: Software Interrupt #4
	0x6d		VME2: Software Interrupt #5
	0x6e		VME2: Software Interrupt #6
	0x6f		VME2: Software Interrupt #7
	0x70		VME2: GCSR Location Monitor #0
	0x71		VME2: GCSR Location Monitor #1
	0x72		VME2: GCSR SIG #0
	0x73		VME2: GCSR SIG #1
	0x74		VME2: GCSR SIG #2
	0x75		VME2: GCSR SIG #3
	0x76		VME2: DMA Controller
	0x77		VME2: VIA
	0x78		VME2: Tick Timer #1
	0x79		VME2: Tick Timer #2
	0x7a		VME2: `IRQ1' feature
	0x7b		VME2: Parity/ECC Error
	0x7c		VME2: Master Write Post Error
	0x7d		VME2: SYSFAIL
	0x7e		VME2: ABORT Switch
	0x7f		VME2: ACFAIL


MVME162/172:
	0x40		IPACK: DMA_a
	0x41		IPACK: DMA_b
	0x42		IPACK: DMA_c
	0x43		IPACK: DMA_d
	0x44		IPACK: Programmable Clock

	0x50 -> 0x52	MC2: <unused>
	0x53		MC2: Timer 4
	0x54		MC2: Timer 3
	0x55		MC2: SCSI
	0x56		MC2: Ethernet `Error'
	0x57		MC2: Ethernet
	0x58		MC2: Timer 2
	0x59		MC2: Timer 1
	0x5a		MC2: <unused>
	0x5b		MC2: Parity/ECC Error
	0x5c		MC2: ZS #1 (vector supplied by ZS chip)
	0x5d		MC2: ZS #2 (vector supplied by ZS chip)
	0x5e		MC2: Abort Switch
	0x5f		MC2: <unused>

	0x60 -> 0x67	VME2: <unused>
	0x68		VME2: Software Interrupt #0
	0x69		VME2: Software Interrupt #1
	0x6a		VME2: Software Interrupt #2
	0x6b		VME2: Software Interrupt #3
	0x6c		VME2: Software Interrupt #4
	0x6d		VME2: Software Interrupt #5
	0x6e		VME2: Software Interrupt #6
	0x6f		VME2: Software Interrupt #7
	0x70		VME2: GCSR Location Monitor #0
	0x71		VME2: GCSR Location Monitor #1
	0x72		VME2: GCSR SIG #0
	0x73		VME2: GCSR SIG #1
	0x74		VME2: GCSR SIG #2
	0x75		VME2: GCSR SIG #3
	0x76		VME2: DMA Controller
	0x77		VME2: VIA
	0x78		VME2: Tick Timer #1
	0x79		VME2: Tick Timer #2
	0x7a		VME2: `IRQ1' feature
	0x7b		VME2: Parity/ECC Error
	0x7c		VME2: Master Write Post Error
	0x7d		VME2: SYSFAIL
	0x7e		VME2: <unused>
	0x7f		VME2: ACFAIL