NetBSD-5.0.2/sys/arch/shark/shark/ns87307reg.h
/* $NetBSD: ns87307reg.h,v 1.5 2007/02/22 16:50:42 thorpej Exp $ */
/*
* Copyright 1997
* Digital Equipment Corporation. All rights reserved.
*
* This software is furnished under license and may be used and
* copied only in accordance with the following terms and conditions.
* Subject to these conditions, you may download, copy, install,
* use, modify and distribute this software in source and/or binary
* form. No title or ownership is transferred hereby.
*
* 1) Any source code used, modified or distributed must reproduce
* and retain this copyright notice and list of conditions as
* they appear in the source file.
*
* 2) No right is granted to use any trade name, trademark, or logo of
* Digital Equipment Corporation. Neither the "Digital Equipment
* Corporation" name nor any trademark or logo of Digital Equipment
* Corporation may be used to endorse or promote products derived
* from this software without the prior written permission of
* Digital Equipment Corporation.
*
* 3) This software is provided "AS-IS" and any express or implied
* warranties, including but not limited to, any implied warranties
* of merchantability, fitness for a particular purpose, or
* non-infringement are disclaimed. In no event shall DIGITAL be
* liable for any damages whatsoever, and in particular, DIGITAL
* shall not be liable for special, indirect, consequential, or
* incidental damages or damages for lost profits, loss of
* revenue or loss of use, whether such damages arise in contract,
* negligence, tort, under statute, in equity, at law or otherwise,
* even if advised of the possibility of such damage.
*/
/*
**++
**
** FACILITY:
**
** ns87307.h
**
** ABSTRACT:
**
**
**
** AUTHORS:
**
** Patrick Crilly Digital Equipment Corporation.
**
** CREATION DATE:
**
** 25-February-1997
**
**--
*/
#ifndef _NS87307REG_H
#define _NS87307REG_H
/*
** Macro for debugging
*/
#define NSIODEBUG
#ifdef NSIODEBUG
#define nsioDebug(x) printf x
#else
#define nsioDebug(x)
#endif
/*
** Base address of chip. Used to configure console
** devices.
*/
#ifndef CONNSIOADDR
#define CONNSIOADDR 0x15c
#endif
/*
** Base Register Offsets
*/
#define NSIO_OFFSET_INDEX 0x00 /* Index register */
#define NSIO_OFFSET_DATA 0x01 /* Data register */
/*
** Number of io ports
*/
#define NSIO_NPORTS 2 /* Number of io ports */
/*
** Card Configuration Registers
*/
#define NSIO_CFG_LOGDEV 0x07 /* Select logical device */
#define NSIO_CFG_SID 0x20 /* Chip SID register */
/*
** Logical Device Configuration Registers
*/
#define NSIO_CFG_ACTIVATE 0x30 /* activate register */
#define NSIO_CFG_IORNGCHK 0x31 /* I/O range check register */
#define NSIO_CFG_IOBASEH 0x60 /* IO port base bits 15-8 */
#define NSIO_CFG_IOBASEL 0x61 /* IO port base bits 7-0 */
#define NSIO_CFG_IRQ 0x70 /* Interrupt Request Level */
#define NSIO_CFG_IRQTYPE 0x71 /* Interrupt Request Type */
#define NSIO_CFG_DMA1 0x74 /* DMA channel for DMA 0 */
#define NSIO_CFG_DMA2 0x75 /* DMA channel for DMA 1 */
#define NSIO_CFG_REG0 0xF0 /* First configuration register */
/*
** KBC Configuration Registers
*/
#define NSIO_KBC_DATAH 0x60 /* kbc data address bits 15-8 */
#define NSIO_KBC_DATAL 0x61 /* kbc data address bits 7-0 */
#define NSIO_KBC_CMDH 0x62 /* kbc cmd address bits 15-8 */
#define NSIO_KBC_CMDL 0x63 /* kbc cmd address bits 7-0 */
#define NSIO_KBC_CFG 0xF0 /* kbc Super I/O cfg register */
/*
** Chip SID defines
*/
#define NSIO_CHIP_ID_MASK 0xFC /* Mask to obtain chip id */
#define NSIO_CHIP_ID 0xC0 /* ns87307 chip id */
/*
** Interrupt Type Masks
*/
#define NSIO_IRQ_LEVEL 0x01 /* Trigger, level = 1 edge = 0 */
#define NSIO_IRQ_HIGH 0x02 /* Int level, high = 1 low = 0 */
#define NSIO_IRQ_LOW 0x00
/*
** IO Range check bit masks
*/
#define NSIO_RNGCHK_ENABLE 0x02 /* Enable IO range checking */
#define NSIO_RNGCHK_USE55 0x01 /* Set to read 0x55 */
/*
** Logical Devices
*/
#define NSIO_DEV_KBC 0 /* keyboard controller */
#define NSIO_DEV_MOUSE 1 /* mouse controller */
#define NSIO_DEV_RTC 2 /* real-time clock */
#define NSIO_DEV_FDC 3 /* floppy disk controller */
#define NSIO_DEV_LPT 4 /* parallel port */
#define NSIO_DEV_USI 5 /* USI = UART + inafred */
#define NSIO_DEV_UART 6 /* UART */
#define NSIO_DEV_GPIO 7 /* gerneral purpose I/O */
#define NSIO_DEV_PWR 8 /* power management */
/*
** PARREL PORT CONFIGURATION
*/
#define NSIO_LPT_TRISTATE_DISABLE (0 << 0) /* tri-state when inactive */
#define NSIO_LPT_TRISTATE_ENABLE (1 << 0) /* tri-state when inactive */
#define NSIO_LPT_CLOCK_DISABLE (0 << 1) /* report ecp mode */
#define NSIO_LPT_CLOCK_ENABLE (1 (( 1) /* ecp/epp timeout function when active */
/* bit 2 reserved */
#define NSIO_LPT_REPORT_ECP (0 << 3) /* report ecp mode */
#define NSIO_LPT_REPORT_SPP (1 << 3) /* report spp mode */
#define NSIO_LPT_REG403_DISABLE (0 << 4) /* dont respond to reg 403 */
#define NSIO_LPT_REG403_ENABLE (1 << 4) /* respond to reg 403 */
#define NSIO_LPT_SPP_NORMAL (0x0<< 5)
#define NSIO_LPT_SPP_EXTENDED (0x1<< 5)
#define NSIO_LPT_EPP_V_1_7 (0x2<< 5)
#define NSIO_LPT_EPP_V_1_9 (0x3<< 5)
#define NSIO_LPT_ECP_NO_EPP (0x4<< 5)
/* bit7-5 0x5 reserved */
/* bit7-5 0x6 reserved */
#define NSIO_LPT_ECP_AND_EPP4 (0x7<< 5)
/*
** As there are two devices which can be used for serial
** communication, set up defines so it's easy to configure
** the logical devices used for serial communication.
*/
#define NSIO_DEV_COM0 NSIO_DEV_UART
#define NSIO_DEV_COM1 NSIO_DEV_USI
/*---------------------------------------------------------------------------*/
/* Macros used to configure logical devices */
/*---------------------------------------------------------------------------*/
/*
** NSIO_READ_REG
**
** Read a configuration register. Use the currently
** selected logical device.
**
** sc pointer to nsio devices softc
** reg index of register to read
** value value read from register
*/
#define NSIO_READ_REG( iot, ioh, reg, value ) \
{ \
bus_space_write_1(iot, ioh, NSIO_OFFSET_INDEX, reg ); \
value = bus_space_read_1( iot, ioh, NSIO_OFFSET_DATA ); \
}
/*
** NSIO_WRITE_REG
**
** Write to a configuration register. Use the currently
** selected logical device.
**
** sc pointer to nsio devices softc
** reg index of register to read
** value value read from register
*/
#define NSIO_WRITE_REG( iot, ioh, reg, value ) \
{ \
bus_space_write_1(iot, ioh, NSIO_OFFSET_INDEX, reg ); \
bus_space_write_1( iot, ioh, NSIO_OFFSET_DATA, value ); \
}
/*
** NSIO_SELECT_DEV
**
** Select logDev as the current the logical device
**
** sc pointer to nsio devices softc
** reg index of register to read
** logDev logical device to select
*/
#define NSIO_SELECT_DEV( iot, ioh, logDev ) \
NSIO_WRITE_REG( iot, ioh, NSIO_CFG_LOGDEV, logDev )
/*
** NSIO_CONFIG_IRQ
**
** Set the irq number and triggering for the currently
** selected logical device. If irqNum is unknown
** the number won't be set and the device will be left
** with it's default value.
**
** sc pointer to nsio devices softc
** irqNum irq number to set
** irqType trigger flags e.g. edge/level, high/low
*/
#define NSIO_CONFIG_IRQ( iot, ioh, irqNum, irqType ) \
{ \
if ( irqNum != -1 ) \
{ \
NSIO_WRITE_REG( iot, ioh, NSIO_CFG_IRQ, irqNum ); \
} \
NSIO_WRITE_REG( iot, ioh, NSIO_CFG_IRQTYPE, irqType ); \
}
/*
** NSIO_CONFIG_KBCCMD
**
** Set the io base for the currently selected logical device.
**
** sc pointer to nsio devices softc
** ioBase address to set io base to
*/
#define NSIO_CONFIG_IOBASE( iot, ioh, ioBase ) \
{ \
NSIO_WRITE_REG( iot, ioh, NSIO_CFG_IOBASEH, \
(unsigned char)(((ioBase) >> 8) & 0xff) ); \
NSIO_WRITE_REG( iot, ioh, NSIO_CFG_IOBASEL, \
(unsigned char)(((ioBase) & 0xff ) ); \
}
/*
** NSIO_CONFIG_KBCDATA
**
** Set the data base for the keyboard. The keyboard
** controller must be the currently selected logical device.
**
** sc pointer to nsio devices softc
** dataBase address to set data base to
*/
#define NSIO_CONFIG_KBCDATA( iot, ioh, dataBase ) \
{ \
NSIO_WRITE_REG( iot, ioh, NSIO_KBC_DATAH, \
(unsigned char)(((dataBase) >> 8) & 0xff) ); \
NSIO_WRITE_REG( iot, ioh, NSIO_KBC_DATAL, \
(unsigned char)((dataBase) & 0xff ) ); \
}
/*
** NSIO_CONFIG_KBCCMD
**
** Set the command base for the keyboard. The keyboard
** controller must be the currently selected logical device.
**
** sc pointer to nsio devices softc
** cmdBase address to set command base to
*/
#define NSIO_CONFIG_KBCCMD( iot, ioh, cmdBase ) \
{ \
NSIO_WRITE_REG( iot, ioh, NSIO_KBC_CMDH, \
(unsigned char)(((cmdBase) >> 8) & 0xff) ); \
NSIO_WRITE_REG( iot, ioh, NSIO_KBC_CMDL, \
(unsigned char)((cmdBase) & 0xff ) ); \
}
/*
** NSIO_ACTIVATE_DEV
**
** Activate the currently selected logical device.
**
** sc pointer to nsio devices softc
*/
#define NSIO_ACTIVATE_DEV( iot, ioh ) \
{ \
NSIO_WRITE_REG( iot, ioh, NSIO_CFG_ACTIVATE, (0x01) ); \
}
/*
** NSIO_DEACTIVATE_DEV
**
** Deactivate the currently selected logical device.
**
** sc pointer to nsio devices softc
*/
#define NSIO_DEACTIVATE_DEV( iot, ioh ) \
{ \
NSIO_WRITE_REG( iot, ioh, NSIO_CFG_ACTIVATE, (0x00) ); \
}
/*
** NSIO_CONFIG_DEBUG
**
** Print out configuration information for the device
**
** sc pointer to nsio devices softc
*/
#ifdef DDB
#define NSIO_CONFIG_DEBUG( iot, ioh ) \
{ \
/* nsioConfigPrint( iot, ioh ); */ \
}
#else
#define NSIO_CONFIG_DEBUG( iot, ioh )
#endif
/*
** NSIO_CONFIG_KBCDEBUG
**
** Print out configuration information for the keyboard device
**
** sc pointer to nsio devices softc
*/
#ifdef DDB
#define NSIO_CONFIG_KBCDEBUG( iot, ioh ) \
{ \
u_char cmdL; \
u_char cmdH; \
/* nsioConfigPrint( iot, ioh ); */ \
NSIO_READ_REG( iot, ioh, NSIO_KBC_CMDH, cmdH ); \
NSIO_READ_REG( iot, ioh, NSIO_KBC_CMDH, cmdL ); \
printf("kbc command: %x\n", (((u_short)(cmdH)) << 8)| cmdL ); \
}
#else
#define NSIO_CONFIG_KBCDEBUG( iot, ioh )
#endif
/* Functions to help configure the ns87307 logical devices.
*/
int i87307KbdConfig(bus_space_tag_t, u_int, u_int);
int i87307MouseConfig(bus_space_tag_t, u_int);
int i87307PrinterConfig(bus_space_tag_t, u_int);
void nsioConfigPrint(bus_space_tag_t, bus_space_handle_t);
#endif /* _NS87307REG_H */