NetBSD-5.0.2/sys/dev/ic/cy.c
/* $NetBSD: cy.c,v 1.56 2008/05/25 19:22:21 ad Exp $ */
/*
* cy.c
*
* Driver for Cyclades Cyclom-8/16/32 multiport serial cards
* (currently not tested with Cyclom-32 cards)
*
* Timo Rossi, 1996
*
* Supports both ISA and PCI Cyclom cards
*
* Lots of debug output can be enabled by defining CY_DEBUG
* Some debugging counters (number of receive/transmit interrupts etc.)
* can be enabled by defining CY_DEBUG1
*/
#include <sys/cdefs.h>
__KERNEL_RCSID(0, "$NetBSD: cy.c,v 1.56 2008/05/25 19:22:21 ad Exp $");
#include <sys/param.h>
#include <sys/ioctl.h>
#include <sys/syslog.h>
#include <sys/fcntl.h>
#include <sys/tty.h>
#include <sys/proc.h>
#include <sys/conf.h>
#include <sys/user.h>
#include <sys/select.h>
#include <sys/device.h>
#include <sys/malloc.h>
#include <sys/systm.h>
#include <sys/callout.h>
#include <sys/kauth.h>
#include <sys/bus.h>
#include <dev/ic/cd1400reg.h>
#include <dev/ic/cyreg.h>
#include <dev/ic/cyvar.h>
static int cyparam(struct tty *, struct termios *);
static void cystart(struct tty *);
static void cy_poll(void *);
static int cy_modem_control(struct cy_softc *, struct cy_port *, int, int);
static void cy_enable_transmitter(struct cy_softc *, struct cy_port *);
static void cd1400_channel_cmd(struct cy_softc *, struct cy_port *, int);
static int cy_speed(speed_t, int *, int *, int);
extern struct cfdriver cy_cd;
static dev_type_open(cyopen);
static dev_type_close(cyclose);
static dev_type_read(cyread);
static dev_type_write(cywrite);
static dev_type_ioctl(cyioctl);
static dev_type_stop(cystop);
static dev_type_tty(cytty);
static dev_type_poll(cypoll);
const struct cdevsw cy_cdevsw = {
.d_open = cyopen,
.d_close = cyclose,
.d_read = cyread,
.d_write = cywrite,
.d_ioctl = cyioctl,
.d_stop = cystop,
.d_tty = cytty,
.d_poll = cypoll,
.d_mmap = nommap,
.d_kqfilter = ttykqfilter,
.d_flag = D_TTY
};
static int cy_open = 0;
static int cy_events = 0;
int cy_attached_ttys;
bool cy_callout_init;
callout_t cy_poll_callout;
/*
* Common probe routine
*/
int
cy_find(struct cy_softc *sc)
{
int cy_chip, chip;
u_char firmware_ver;
bus_space_tag_t tag = sc->sc_memt;
bus_space_handle_t bsh = sc->sc_bsh;
int bustype = sc->sc_bustype;
/* Cyclom card hardware reset */
bus_space_write_1(tag, bsh, CY16_RESET << bustype, 0);
DELAY(500); /* wait for reset to complete */
bus_space_write_1(tag, bsh, CY_CLEAR_INTR << bustype, 0);
#ifdef CY_DEBUG
printf("cy: card reset done\n");
#endif
sc->sc_nchips = 0;
for (cy_chip = 0, chip = 0; cy_chip < CY_MAX_CD1400s;
cy_chip++, chip += (CY_CD1400_MEMSPACING << bustype)) {
int i;
/*
* the last 4 nchips are 'interleaved' with the first 4 on
* 32-port boards
*/
if (cy_chip == 4)
chip -= (CY32_ADDR_FIX << bustype);
#ifdef CY_DEBUG
printf("sy: probe chip %d offset 0x%x ... ", cy_chip, chip);
#endif
/* wait until the chip is ready for command */
DELAY(1000);
if (bus_space_read_1(tag, bsh, chip +
((CD1400_CCR << 1) << bustype)) != 0) {
#ifdef CY_DEBUG
printf("not ready for command\n");
#endif
break;
}
/* clear the firmware version reg. */
bus_space_write_1(tag, bsh, chip +
((CD1400_GFRCR << 1) << bustype), 0);
/*
* On Cyclom-16 references to non-existent chip 4
* actually access chip 0 (address line 9 not decoded).
* Here we check if the clearing of chip 4 GFRCR actually
* cleared chip 0 GFRCR. In that case we have a 16 port card.
*/
if (cy_chip == 4 &&
bus_space_read_1(tag, bsh, /* off for chip 0 (0) + */
((CD1400_GFRCR << 1) << bustype)) == 0)
break;
/* reset the chip */
bus_space_write_1(tag, bsh, chip +
((CD1400_CCR << 1) << bustype),
CD1400_CCR_CMDRESET | CD1400_CCR_FULLRESET);
/* wait for the chip to initialize itself */
for (i = 0; i < 200; i++) {
DELAY(50);
firmware_ver = bus_space_read_1(tag, bsh, chip +
((CD1400_GFRCR << 1) << bustype));
if ((firmware_ver & 0xf0) == 0x40) /* found a CD1400 */
break;
}
#ifdef CY_DEBUG
printf("firmware version 0x%x\n", firmware_ver);
#endif
if ((firmware_ver & 0xf0) != 0x40)
break;
/* firmware version OK, CD1400 found */
sc->sc_nchips++;
}
if (sc->sc_nchips == 0) {
#ifdef CY_DEBUG
printf("no CD1400s found\n");
#endif
return 0;
}
#ifdef CY_DEBUG
printf("found %d CD1400s\n", sc->sc_nchips);
#endif
return 1;
}
void
cy_attach(struct cy_softc *sc)
{
int port, cy_chip, num_chips, cdu, chip;
int cy_clock;
if (!cy_callout_init) {
cy_callout_init = true;
callout_init(&cy_poll_callout, 0);
}
num_chips = sc->sc_nchips;
if (num_chips == 0)
return;
memset(sc->sc_ports, 0, sizeof(sc->sc_ports));
port = 0;
for (cy_chip = 0, chip = 0; cy_chip < num_chips; cy_chip++,
chip += (CY_CD1400_MEMSPACING << sc->sc_bustype)) {
if (cy_chip == 4)
chip -= (CY32_ADDR_FIX << sc->sc_bustype);
#ifdef CY_DEBUG
aprint_debug("attach CD1400 #%d offset 0x%x\n", cy_chip, chip);
#endif
sc->sc_cd1400_offs[cy_chip] = chip;
/*
* configure port 0 as serial port (should already be after
* reset)
*/
cd_write_reg(sc, cy_chip, CD1400_GCR, 0);
if (cd_read_reg(sc, cy_chip, CD1400_GFRCR) <= 0x46)
cy_clock = CY_CLOCK;
else
cy_clock = CY_CLOCK_60;
/* set up a receive timeout period (1ms) */
cd_write_reg(sc, cy_chip, CD1400_PPR,
(cy_clock / CD1400_PPR_PRESCALER / 1000) + 1);
for (cdu = 0; cdu < CD1400_NO_OF_CHANNELS; cdu++) {
sc->sc_ports[port].cy_softc = sc;
sc->sc_ports[port].cy_port_num = port;
sc->sc_ports[port].cy_chip = cy_chip;
sc->sc_ports[port].cy_clock = cy_clock;
/* should we initialize anything else here? */
port++;
} /* for(each port on one CD1400...) */
} /* for(each CD1400 on a card... ) */
sc->sc_nchannels = port;
aprint_normal_dev(sc->sc_dev, "%d channels (ttyCY%03d..ttyCY%03d)\n",
sc->sc_nchannels, cy_attached_ttys,
cy_attached_ttys + (sc->sc_nchannels - 1));
cy_attached_ttys += sc->sc_nchannels;
/* ensure an edge for the next interrupt */
bus_space_write_1(sc->sc_memt, sc->sc_bsh,
CY_CLEAR_INTR << sc->sc_bustype, 0);
}
#define CYDIALOUT_MASK 0x80000
#define CY_DIALOUT(dev) (minor(dev) & CYDIALOUT_MASK)
#define CY_PORT(dev) cy_getport((dev))
#define CY_BOARD(cy) ((cy)->cy_softc)
static struct cy_port *
cy_getport(dev_t dev)
{
int i, j, k, u = minor(dev) & ~CYDIALOUT_MASK;
struct cy_softc *sc;
for (i = 0, j = 0; i < cy_cd.cd_ndevs; i++) {
k = j;
sc = device_lookup_private(&cy_cd, i);
if (sc == NULL)
continue;
if (sc->sc_nchannels == 0)
continue;
j += sc->sc_nchannels;
if (j > u)
return (&sc->sc_ports[u - k]);
}
return (NULL);
}
/*
* open routine. returns zero if successful, else error code
*/
int
cyopen(dev_t dev, int flag, int mode, struct lwp *l)
{
struct cy_softc *sc;
struct cy_port *cy;
struct tty *tp;
int s, error;
cy = CY_PORT(dev);
if (cy == NULL)
return (ENXIO);
sc = CY_BOARD(cy);
s = spltty();
if (cy->cy_tty == NULL) {
if ((cy->cy_tty = ttymalloc()) == NULL) {
splx(s);
aprint_error_dev(sc->sc_dev,
"port %d: can't allocate tty\n",
cy->cy_port_num);
return (ENOMEM);
}
tty_attach(cy->cy_tty);
}
splx(s);
tp = cy->cy_tty;
tp->t_oproc = cystart;
tp->t_param = cyparam;
tp->t_dev = dev;
if (kauth_authorize_device_tty(l->l_cred, KAUTH_DEVICE_TTY_OPEN, tp))
return (EBUSY);
if (!ISSET(tp->t_state, TS_ISOPEN) && tp->t_wopen == 0) {
ttychars(tp);
tp->t_iflag = TTYDEF_IFLAG;
tp->t_oflag = TTYDEF_OFLAG;
tp->t_cflag = TTYDEF_CFLAG;
if (ISSET(cy->cy_openflags, TIOCFLAG_CLOCAL))
SET(tp->t_cflag, CLOCAL);
if (ISSET(cy->cy_openflags, TIOCFLAG_CRTSCTS))
SET(tp->t_cflag, CRTSCTS);
if (ISSET(cy->cy_openflags, TIOCFLAG_MDMBUF))
SET(tp->t_cflag, MDMBUF);
tp->t_lflag = TTYDEF_LFLAG;
tp->t_ispeed = tp->t_ospeed = TTYDEF_SPEED;
s = spltty();
/*
* Allocate input ring buffer if we don't already have one
*/
if (cy->cy_ibuf == NULL) {
cy->cy_ibuf = malloc(CY_IBUF_SIZE, M_DEVBUF, M_NOWAIT);
if (cy->cy_ibuf == NULL) {
aprint_error_dev(sc->sc_dev,
"port %d: can't allocate input buffer\n",
cy->cy_port_num);
splx(s);
return ENOMEM;
}
cy->cy_ibuf_end = cy->cy_ibuf + CY_IBUF_SIZE;
}
/* mark the ring buffer as empty */
cy->cy_ibuf_rd_ptr = cy->cy_ibuf_wr_ptr = cy->cy_ibuf;
/* select CD1400 channel */
cd_write_reg(sc, cy->cy_chip, CD1400_CAR,
cy->cy_port_num & CD1400_CAR_CHAN);
/* reset the channel */
cd1400_channel_cmd(sc, cy, CD1400_CCR_CMDRESET);
/* encode unit (port) number in LIVR */
/* there is just enough space for 5 bits (32 ports) */
cd_write_reg(sc, cy->cy_chip, CD1400_LIVR,
cy->cy_port_num << 3);
cy->cy_channel_control = 0;
/* hmm... need spltty() here? */
if (cy_open == 0) {
cy_open = 1;
callout_reset(&cy_poll_callout, 1, cy_poll, NULL);
}
/* this sets parameters and raises DTR */
cyparam(tp, &tp->t_termios);
ttsetwater(tp);
/* raise RTS too */
cy_modem_control(sc, cy, TIOCM_RTS, DMBIS);
cy->cy_carrier_stat =
cd_read_reg(sc, cy->cy_chip, CD1400_MSVR2);
/* enable receiver and modem change interrupts */
cd_write_reg(sc, cy->cy_chip, CD1400_SRER,
CD1400_SRER_MDMCH | CD1400_SRER_RXDATA);
if (CY_DIALOUT(dev) ||
ISSET(cy->cy_openflags, TIOCFLAG_SOFTCAR) ||
ISSET(tp->t_cflag, MDMBUF) ||
ISSET(cy->cy_carrier_stat, CD1400_MSVR2_CD))
SET(tp->t_state, TS_CARR_ON);
else
CLR(tp->t_state, TS_CARR_ON);
splx(s);
}
/* wait for carrier if necessary */
if (!ISSET(flag, O_NONBLOCK)) {
mutex_spin_enter(&tty_lock);
while (!ISSET(tp->t_cflag, CLOCAL) &&
!ISSET(tp->t_state, TS_CARR_ON)) {
tp->t_wopen++;
error = ttysleep(tp, &tp->t_rawcv, true, 0);
tp->t_wopen--;
if (error != 0) {
mutex_spin_exit(&tty_lock);
return error;
}
}
mutex_spin_exit(&tty_lock);
}
return (*tp->t_linesw->l_open) (dev, tp);
}
/*
* close routine. returns zero if successful, else error code
*/
int
cyclose(dev_t dev, int flag, int mode, struct lwp *l)
{
struct cy_softc *sc;
struct cy_port *cy;
struct tty *tp;
int s;
cy = CY_PORT(dev);
sc = CY_BOARD(cy);
tp = cy->cy_tty;
(*tp->t_linesw->l_close) (tp, flag);
s = spltty();
if (ISSET(tp->t_cflag, HUPCL) &&
!ISSET(cy->cy_openflags, TIOCFLAG_SOFTCAR)) {
/*
* drop DTR and RTS (should we wait for output buffer to
* become empty first?)
*/
cy_modem_control(sc, cy, 0, DMSET);
}
/*
* XXX should we disable modem change and
* receive interrupts here or somewhere ?
*/
CLR(tp->t_state, TS_BUSY | TS_FLUSH);
splx(s);
ttyclose(tp);
return 0;
}
/*
* Read routine
*/
int
cyread(dev_t dev, struct uio *uio, int flag)
{
struct cy_port *cy;
struct tty *tp;
cy = CY_PORT(dev);
tp = cy->cy_tty;
return ((*tp->t_linesw->l_read)(tp, uio, flag));
}
/*
* Write routine
*/
int
cywrite(dev_t dev, struct uio *uio, int flag)
{
struct cy_port *cy;
struct tty *tp;
cy = CY_PORT(dev);
tp = cy->cy_tty;
return ((*tp->t_linesw->l_write)(tp, uio, flag));
}
/*
* Poll routine
*/
int
cypoll(dev_t dev, int events, struct lwp *l)
{
struct cy_port *cy;
struct tty *tp;
cy = CY_PORT(dev);
tp = cy->cy_tty;
return ((*tp->t_linesw->l_poll)(tp, events, l));
}
/*
* return tty pointer
*/
struct tty *
cytty(dev_t dev)
{
struct cy_port *cy;
cy = CY_PORT(dev);
return (cy->cy_tty);
}
/*
* ioctl routine
*/
int
cyioctl(dev_t dev, u_long cmd, void *data, int flag, struct lwp *l)
{
struct cy_softc *sc;
struct cy_port *cy;
struct tty *tp;
int error;
cy = CY_PORT(dev);
sc = CY_BOARD(cy);
tp = cy->cy_tty;
error = (*tp->t_linesw->l_ioctl)(tp, cmd, data, flag, l);
if (error != EPASSTHROUGH)
return error;
error = ttioctl(tp, cmd, data, flag, l);
if (error != EPASSTHROUGH)
return error;
/* XXX should not allow dropping DTR when dialin? */
switch (cmd) {
case TIOCSBRK: /* start break */
SET(cy->cy_flags, CY_F_START_BREAK);
cy_enable_transmitter(sc, cy);
break;
case TIOCCBRK: /* stop break */
SET(cy->cy_flags, CY_F_END_BREAK);
cy_enable_transmitter(sc, cy);
break;
case TIOCSDTR: /* DTR on */
cy_modem_control(sc, cy, TIOCM_DTR, DMBIS);
break;
case TIOCCDTR: /* DTR off */
cy_modem_control(sc, cy, TIOCM_DTR, DMBIC);
break;
case TIOCMSET: /* set new modem control line values */
cy_modem_control(sc, cy, *((int *) data), DMSET);
break;
case TIOCMBIS: /* turn modem control bits on */
cy_modem_control(sc, cy, *((int *) data), DMBIS);
break;
case TIOCMBIC: /* turn modem control bits off */
cy_modem_control(sc, cy, *((int *) data), DMBIC);
break;
case TIOCMGET: /* get modem control/status line state */
*((int *) data) = cy_modem_control(sc, cy, 0, DMGET);
break;
case TIOCGFLAGS:
*((int *) data) = cy->cy_openflags |
(CY_DIALOUT(dev) ? TIOCFLAG_SOFTCAR : 0);
break;
case TIOCSFLAGS:
error = kauth_authorize_device_tty(l->l_cred,
KAUTH_DEVICE_TTY_PRIVSET, tp);
if (error != 0)
return EPERM;
cy->cy_openflags = *((int *) data) &
(TIOCFLAG_SOFTCAR | TIOCFLAG_CLOCAL |
TIOCFLAG_CRTSCTS | TIOCFLAG_MDMBUF);
break;
default:
return EPASSTHROUGH;
}
return 0;
}
/*
* start output
*/
void
cystart(struct tty *tp)
{
struct cy_softc *sc;
struct cy_port *cy;
int s;
cy = CY_PORT(tp->t_dev);
sc = cy->cy_softc;
s = spltty();
#ifdef CY_DEBUG1
cy->cy_start_count++;
#endif
if (!ISSET(tp->t_state, TS_TTSTOP | TS_TIMEOUT | TS_BUSY)) {
if (!ttypull(tp))
goto out;
SET(tp->t_state, TS_BUSY);
cy_enable_transmitter(sc, cy);
}
out:
splx(s);
}
/*
* stop output
*/
void
cystop(struct tty *tp, int flag)
{
struct cy_port *cy;
int s;
cy = CY_PORT(tp->t_dev);
s = spltty();
if (ISSET(tp->t_state, TS_BUSY)) {
if (!ISSET(tp->t_state, TS_TTSTOP))
SET(tp->t_state, TS_FLUSH);
/*
* the transmit interrupt routine will disable transmit when it
* notices that CY_F_STOP has been set.
*/
SET(cy->cy_flags, CY_F_STOP);
}
splx(s);
}
/*
* parameter setting routine.
* returns 0 if successful, else returns error code
*/
int
cyparam(struct tty *tp, struct termios *t)
{
struct cy_softc *sc;
struct cy_port *cy;
int ibpr = 0, obpr = 0, i_clk_opt = 0, o_clk_opt = 0; /* XXX: GCC */
int s, opt;
cy = CY_PORT(tp->t_dev);
sc = CY_BOARD(cy);
if (t->c_ospeed != 0 && cy_speed(t->c_ospeed, &o_clk_opt, &obpr, cy->cy_clock) < 0)
return EINVAL;
if (t->c_ispeed != 0 && cy_speed(t->c_ispeed, &i_clk_opt, &ibpr, cy->cy_clock) < 0)
return EINVAL;
s = spltty();
/* hang up the line is ospeed is zero, else turn DTR on */
cy_modem_control(sc, cy, TIOCM_DTR, (t->c_ospeed == 0 ? DMBIC : DMBIS));
/* channel was selected by the above call to cy_modem_control() */
#if 0
cd_write_reg(sc, cy->cy_chip, CD1400_CAR, port & CD1400_CAR_CHAN);
#endif
/* set transmit speed */
if (t->c_ospeed != 0) {
cd_write_reg(sc, cy->cy_chip, CD1400_TCOR, o_clk_opt);
cd_write_reg(sc, cy->cy_chip, CD1400_TBPR, obpr);
}
/* set receive speed */
if (t->c_ispeed != 0) {
cd_write_reg(sc, cy->cy_chip, CD1400_RCOR, i_clk_opt);
cd_write_reg(sc, cy->cy_chip, CD1400_RBPR, ibpr);
}
opt = CD1400_CCR_CMDCHANCTL | CD1400_CCR_XMTEN
| (ISSET(t->c_cflag, CREAD) ? CD1400_CCR_RCVEN : CD1400_CCR_RCVDIS);
if (opt != cy->cy_channel_control) {
cy->cy_channel_control = opt;
cd1400_channel_cmd(sc, cy, opt);
}
/* compute COR1 contents */
opt = 0;
if (ISSET(t->c_cflag, PARENB)) {
if (ISSET(t->c_cflag, PARODD))
opt |= CD1400_COR1_PARODD;
opt |= CD1400_COR1_PARNORMAL;
}
if (!ISSET(t->c_iflag, INPCK))
opt |= CD1400_COR1_NOINPCK; /* no parity checking */
if (ISSET(t->c_cflag, CSTOPB))
opt |= CD1400_COR1_STOP2;
switch (t->c_cflag & CSIZE) {
case CS5:
opt |= CD1400_COR1_CS5;
break;
case CS6:
opt |= CD1400_COR1_CS6;
break;
case CS7:
opt |= CD1400_COR1_CS7;
break;
default:
opt |= CD1400_COR1_CS8;
break;
}
cd_write_reg(sc, cy->cy_chip, CD1400_COR1, opt);
#ifdef CY_DEBUG
printf("cor1 = 0x%x...", opt);
#endif
/*
* use the CD1400 automatic CTS flow control if CRTSCTS is set
*
* CD1400_COR2_ETC is used because breaks are generated with
* embedded transmit commands
*/
cd_write_reg(sc, cy->cy_chip, CD1400_COR2,
CD1400_COR2_ETC |
(ISSET(t->c_cflag, CRTSCTS) ? CD1400_COR2_CCTS_OFLOW : 0));
cd_write_reg(sc, cy->cy_chip, CD1400_COR3, CY_RX_FIFO_THRESHOLD);
cd1400_channel_cmd(sc, cy, CD1400_CCR_CMDCORCHG |
CD1400_CCR_COR1 | CD1400_CCR_COR2 | CD1400_CCR_COR3);
cd_write_reg(sc, cy->cy_chip, CD1400_COR4, CD1400_COR4_PFO_EXCEPTION);
cd_write_reg(sc, cy->cy_chip, CD1400_COR5, 0);
/*
* set modem change option registers to generate interrupts
* on carrier detect changes.
*
* if hardware RTS handshaking is used
* also set the handshaking threshold.
*/
if (cy->cy_clock == CY_CLOCK_60) {
cd_write_reg(sc, cy->cy_chip, CD1400_MCOR1, CD1400_MCOR1_CDzd |
(ISSET(t->c_cflag, CRTSCTS) ? CY_RX_DTR_THRESHOLD : 0));
} else {
cd_write_reg(sc, cy->cy_chip, CD1400_MCOR1, CD1400_MCOR1_CDzd);
}
cd_write_reg(sc, cy->cy_chip, CD1400_MCOR2, CD1400_MCOR2_CDod);
/*
* set receive timeout to approx. 2ms
* could use more complex logic here...
* (but is it actually needed or even useful?)
*/
cd_write_reg(sc, cy->cy_chip, CD1400_RTPR, 2);
/*
* should do anything else here?
* XXX check MDMBUF handshaking like in com.c?
*/
splx(s);
return 0;
}
/*
* set/get modem line status
*
* bits can be: TIOCM_DTR, TIOCM_RTS, TIOCM_CTS, TIOCM_CD, TIOCM_RI, TIOCM_DSR
*/
int
cy_modem_control(struct cy_softc *sc, struct cy_port *cy, int bits, int howto)
{
struct tty *tp = cy->cy_tty;
int s, msvr;
s = spltty();
/* select channel */
cd_write_reg(sc, cy->cy_chip, CD1400_CAR,
cy->cy_port_num & CD1400_CAR_CHAN);
/* Does not manipulate RTS if it is used for flow control. */
switch (howto) {
case DMGET:
bits = 0;
if (cy->cy_channel_control & CD1400_CCR_RCVEN)
bits |= TIOCM_LE;
msvr = cd_read_reg(sc, cy->cy_chip, CD1400_MSVR2);
if (cy->cy_clock == CY_CLOCK_60) {
if (cd_read_reg(sc, cy->cy_chip, CD1400_MSVR1) &
CD1400_MSVR1_RTS)
bits |= TIOCM_DTR;
if (msvr & CD1400_MSVR2_DTR)
bits |= TIOCM_RTS;
} else {
if (cd_read_reg(sc, cy->cy_chip, CD1400_MSVR1) &
CD1400_MSVR1_RTS)
bits |= TIOCM_RTS;
if (msvr & CD1400_MSVR2_DTR)
bits |= TIOCM_DTR;
}
if (msvr & CD1400_MSVR2_CTS)
bits |= TIOCM_CTS;
if (msvr & CD1400_MSVR2_CD)
bits |= TIOCM_CD;
/* Not connected on some Cyclom-Y boards? */
if (msvr & CD1400_MSVR2_DSR)
bits |= TIOCM_DSR;
/* Not connected on some Cyclom-8Y boards? */
if (msvr & CD1400_MSVR2_RI)
bits |= TIOCM_RI;
break;
case DMSET: /* replace old values with new ones */
if (cy->cy_clock == CY_CLOCK_60) {
if (!ISSET(tp->t_cflag, CRTSCTS))
cd_write_reg(sc, cy->cy_chip, CD1400_MSVR2,
((bits & TIOCM_RTS) ? CD1400_MSVR2_DTR : 0));
cd_write_reg(sc, cy->cy_chip, CD1400_MSVR1,
((bits & TIOCM_DTR) ? CD1400_MSVR1_RTS : 0));
} else {
if (!ISSET(tp->t_cflag, CRTSCTS))
cd_write_reg(sc, cy->cy_chip, CD1400_MSVR1,
((bits & TIOCM_RTS) ? CD1400_MSVR1_RTS : 0));
cd_write_reg(sc, cy->cy_chip, CD1400_MSVR2,
((bits & TIOCM_DTR) ? CD1400_MSVR2_DTR : 0));
}
break;
case DMBIS: /* set bits */
if (cy->cy_clock == CY_CLOCK_60) {
if (!ISSET(tp->t_cflag, CRTSCTS) &&
(bits & TIOCM_RTS) != 0)
cd_write_reg(sc, cy->cy_chip, CD1400_MSVR2,
CD1400_MSVR2_DTR);
if (bits & TIOCM_DTR)
cd_write_reg(sc, cy->cy_chip, CD1400_MSVR1,
CD1400_MSVR1_RTS);
} else {
if (!ISSET(tp->t_cflag, CRTSCTS) &&
(bits & TIOCM_RTS) != 0)
cd_write_reg(sc, cy->cy_chip, CD1400_MSVR1,
CD1400_MSVR1_RTS);
if (bits & TIOCM_DTR)
cd_write_reg(sc, cy->cy_chip, CD1400_MSVR2,
CD1400_MSVR2_DTR);
}
break;
case DMBIC: /* clear bits */
if (cy->cy_clock == CY_CLOCK_60) {
if (!ISSET(tp->t_cflag, CRTSCTS) && (bits & TIOCM_RTS))
cd_write_reg(sc, cy->cy_chip, CD1400_MSVR2, 0);
if (bits & TIOCM_DTR)
cd_write_reg(sc, cy->cy_chip, CD1400_MSVR1, 0);
} else {
if (!ISSET(tp->t_cflag, CRTSCTS) && (bits & TIOCM_RTS))
cd_write_reg(sc, cy->cy_chip, CD1400_MSVR1, 0);
if (bits & TIOCM_DTR)
cd_write_reg(sc, cy->cy_chip, CD1400_MSVR2, 0);
}
break;
}
splx(s);
return ((howto == DMGET) ? bits : 0);
}
/*
* Upper-level handler loop (called from timer interrupt?)
* This routine is common for multiple cards
*/
void
cy_poll(void *arg)
{
int card, port;
struct cy_softc *sc;
struct cy_port *cy;
struct tty *tp;
static int counter = 0;
#ifdef CY_DEBUG1
int did_something;
#endif
int s = spltty();
if (cy_events == 0 && ++counter < 200) {
splx(s);
goto out;
}
cy_events = 0;
splx(s);
for (card = 0; card < cy_cd.cd_ndevs; card++) {
sc = device_lookup_private(&cy_cd, card);
if (sc == NULL)
continue;
#ifdef CY_DEBUG1
sc->sc_poll_count1++;
did_something = 0;
#endif
for (port = 0; port < sc->sc_nchannels; port++) {
cy = &sc->sc_ports[port];
if ((tp = cy->cy_tty) == NULL || cy->cy_ibuf == NULL ||
(!ISSET(tp->t_state, TS_ISOPEN) && tp->t_wopen == 0))
continue;
/*
* handle received data
*/
while (cy->cy_ibuf_rd_ptr != cy->cy_ibuf_wr_ptr) {
u_char line_stat;
int chr;
line_stat = cy->cy_ibuf_rd_ptr[0];
chr = cy->cy_ibuf_rd_ptr[1];
if (line_stat &
(CD1400_RDSR_BREAK | CD1400_RDSR_FE))
chr |= TTY_FE;
if (line_stat & CD1400_RDSR_PE)
chr |= TTY_PE;
/*
* on an overrun error the data is treated as
* good just as it should be.
*/
#ifdef CY_DEBUG
aprint_debug_dev(sc->sc_dev,
"port %d ttyinput 0x%x\n",
port, chr);
#endif
(*tp->t_linesw->l_rint) (chr, tp);
s = spltty(); /* really necessary? */
if ((cy->cy_ibuf_rd_ptr += 2) ==
cy->cy_ibuf_end)
cy->cy_ibuf_rd_ptr = cy->cy_ibuf;
splx(s);
#ifdef CY_DEBUG1
did_something = 1;
#endif
}
/*
* If we don't have any received data in ibuf and
* CRTSCTS is on and RTS is turned off, it is time to
* turn RTS back on
*/
if (ISSET(tp->t_cflag, CRTSCTS)) {
/*
* we can't use cy_modem_control() here as it
* doesn't change RTS if RTSCTS is on
*/
cd_write_reg(sc, cy->cy_chip, CD1400_CAR,
port & CD1400_CAR_CHAN);
if (cy->cy_clock == CY_CLOCK_60) {
if ((cd_read_reg(sc, cy->cy_chip,
CD1400_MSVR2) & CD1400_MSVR2_DTR) == 0) {
cd_write_reg(sc, cy->cy_chip,
CD1400_MSVR2,CD1400_MSVR2_DTR);
#ifdef CY_DEBUG1
did_something = 1;
#endif
}
} else {
if ((cd_read_reg(sc, cy->cy_chip,
CD1400_MSVR1) & CD1400_MSVR1_RTS) == 0) {
cd_write_reg(sc, cy->cy_chip,
CD1400_MSVR1,CD1400_MSVR1_RTS);
#ifdef CY_DEBUG1
did_something = 1;
#endif
}
}
}
/*
* handle carrier changes
*/
s = spltty();
if (ISSET(cy->cy_flags, CY_F_CARRIER_CHANGED)) {
int carrier;
CLR(cy->cy_flags, CY_F_CARRIER_CHANGED);
splx(s);
carrier = ((cy->cy_carrier_stat &
CD1400_MSVR2_CD) != 0);
#ifdef CY_DEBUG
printf("cy_poll: carrier change "
"(card %d, port %d, carrier %d)\n",
card, port, carrier);
#endif
if (CY_DIALOUT(tp->t_dev) == 0 &&
!(*tp->t_linesw->l_modem)(tp, carrier))
cy_modem_control(sc, cy,
TIOCM_DTR, DMBIC);
#ifdef CY_DEBUG1
did_something = 1;
#endif
} else
splx(s);
s = spltty();
if (ISSET(cy->cy_flags, CY_F_START)) {
CLR(cy->cy_flags, CY_F_START);
splx(s);
(*tp->t_linesw->l_start) (tp);
#ifdef CY_DEBUG1
did_something = 1;
#endif
} else
splx(s);
/* could move this to even upper level... */
if (cy->cy_fifo_overruns) {
cy->cy_fifo_overruns = 0;
/*
* doesn't report overrun count, but
* shouldn't really matter
*/
log(LOG_WARNING, "%s: port %d fifo overrun\n",
device_xname(sc->sc_dev), port);
}
if (cy->cy_ibuf_overruns) {
cy->cy_ibuf_overruns = 0;
log(LOG_WARNING, "%s: port %d ibuf overrun\n",
device_xname(sc->sc_dev), port);
}
} /* for(port...) */
#ifdef CY_DEBUG1
if (did_something && counter >= 200)
sc->sc_poll_count2++;
#endif
} /* for(card...) */
counter = 0;
out:
callout_reset(&cy_poll_callout, 1, cy_poll, NULL);
}
/*
* hardware interrupt routine
*/
int
cy_intr(void *arg)
{
struct cy_softc *sc = arg;
struct cy_port *cy;
int cy_chip, stat;
int int_serviced = 0;
/*
* Check interrupt status of each CD1400 chip on this card
* (multiple cards cannot share the same interrupt)
*/
for (cy_chip = 0; cy_chip < sc->sc_nchips; cy_chip++) {
stat = cd_read_reg(sc, cy_chip, CD1400_SVRR);
if (stat == 0)
continue;
if (ISSET(stat, CD1400_SVRR_RXRDY)) {
u_char save_car, save_rir, serv_type;
u_char line_stat, recv_data, n_chars;
u_char *buf_p;
save_rir = cd_read_reg(sc, cy_chip, CD1400_RIR);
save_car = cd_read_reg(sc, cy_chip, CD1400_CAR);
/* enter rx service */
cd_write_reg(sc, cy_chip, CD1400_CAR, save_rir);
serv_type = cd_read_reg(sc, cy_chip, CD1400_RIVR);
cy = &sc->sc_ports[serv_type >> 3];
#ifdef CY_DEBUG1
cy->cy_rx_int_count++;
#endif
buf_p = cy->cy_ibuf_wr_ptr;
if (ISSET(serv_type, CD1400_RIVR_EXCEPTION)) {
line_stat = cd_read_reg(sc, cy->cy_chip,
CD1400_RDSR);
recv_data = cd_read_reg(sc, cy->cy_chip,
CD1400_RDSR);
if (cy->cy_tty == NULL ||
!ISSET(cy->cy_tty->t_state, TS_ISOPEN))
goto end_rx_serv;
#ifdef CY_DEBUG
aprint_debug_dev(
sc->sc_dev,
"port %d recv exception, "
"line_stat 0x%x, char 0x%x\n",
cy->cy_port_num, line_stat, recv_data);
#endif
if (ISSET(line_stat, CD1400_RDSR_OE))
cy->cy_fifo_overruns++;
*buf_p++ = line_stat;
*buf_p++ = recv_data;
if (buf_p == cy->cy_ibuf_end)
buf_p = cy->cy_ibuf;
if (buf_p == cy->cy_ibuf_rd_ptr) {
if (buf_p == cy->cy_ibuf)
buf_p = cy->cy_ibuf_end;
buf_p -= 2;
cy->cy_ibuf_overruns++;
}
cy_events = 1;
} else {/* no exception, received data OK */
n_chars = cd_read_reg(sc, cy->cy_chip,
CD1400_RDCR);
/* If no tty or not open, discard data */
if (cy->cy_tty == NULL ||
!ISSET(cy->cy_tty->t_state, TS_ISOPEN)) {
while (n_chars--)
(void)cd_read_reg(sc,
cy->cy_chip, CD1400_RDSR);
goto end_rx_serv;
}
#ifdef CY_DEBUG
aprint_debug_dev(sc->sc_dev,
"port %d receive ok %d chars\n",
cy->cy_port_num, n_chars);
#endif
while (n_chars--) {
*buf_p++ = 0; /* status: OK */
/* data byte */
*buf_p++ = cd_read_reg(sc,
cy->cy_chip, CD1400_RDSR);
if (buf_p == cy->cy_ibuf_end)
buf_p = cy->cy_ibuf;
if (buf_p == cy->cy_ibuf_rd_ptr) {
if (buf_p == cy->cy_ibuf)
buf_p = cy->cy_ibuf_end;
buf_p -= 2;
cy->cy_ibuf_overruns++;
break;
}
}
cy_events = 1;
}
cy->cy_ibuf_wr_ptr = buf_p;
/* RTS handshaking for incoming data */
if (ISSET(cy->cy_tty->t_cflag, CRTSCTS)) {
int bf, msvr;
bf = buf_p - cy->cy_ibuf_rd_ptr;
if (bf < 0)
bf += CY_IBUF_SIZE;
if (bf > (CY_IBUF_SIZE / 2)) {
/* turn RTS off */
if (cy->cy_clock == CY_CLOCK_60)
msvr = CD1400_MSVR2;
else
msvr = CD1400_MSVR1;
cd_write_reg(sc, cy->cy_chip, msvr, 0);
}
}
end_rx_serv:
/* terminate service context */
cd_write_reg(sc, cy->cy_chip, CD1400_RIR,
save_rir & 0x3f);
cd_write_reg(sc, cy->cy_chip, CD1400_CAR, save_car);
int_serviced = 1;
} /* if (rx_service...) */
if (ISSET(stat, CD1400_SVRR_MDMCH)) {
u_char save_car, save_mir, serv_type, modem_stat;
save_mir = cd_read_reg(sc, cy_chip, CD1400_MIR);
save_car = cd_read_reg(sc, cy_chip, CD1400_CAR);
/* enter modem service */
cd_write_reg(sc, cy_chip, CD1400_CAR, save_mir);
serv_type = cd_read_reg(sc, cy_chip, CD1400_MIVR);
cy = &sc->sc_ports[serv_type >> 3];
#ifdef CY_DEBUG1
cy->cy_modem_int_count++;
#endif
modem_stat = cd_read_reg(sc, cy->cy_chip, CD1400_MSVR2);
#ifdef CY_DEBUG
aprint_debug_dev(sc->sc_dev,
"port %d modem line change, new stat 0x%x\n",
cy->cy_port_num, modem_stat);
#endif
if (ISSET((cy->cy_carrier_stat ^ modem_stat), CD1400_MSVR2_CD)) {
SET(cy->cy_flags, CY_F_CARRIER_CHANGED);
cy_events = 1;
}
cy->cy_carrier_stat = modem_stat;
/* terminate service context */
cd_write_reg(sc, cy->cy_chip, CD1400_MIR, save_mir & 0x3f);
cd_write_reg(sc, cy->cy_chip, CD1400_CAR, save_car);
int_serviced = 1;
} /* if (modem_service...) */
if (ISSET(stat, CD1400_SVRR_TXRDY)) {
u_char save_car, save_tir, serv_type,
count, ch;
struct tty *tp;
save_tir = cd_read_reg(sc, cy_chip, CD1400_TIR);
save_car = cd_read_reg(sc, cy_chip, CD1400_CAR);
/* enter tx service */
cd_write_reg(sc, cy_chip, CD1400_CAR, save_tir);
serv_type = cd_read_reg(sc, cy_chip, CD1400_TIVR);
cy = &sc->sc_ports[serv_type >> 3];
#ifdef CY_DEBUG1
cy->cy_tx_int_count++;
#endif
#ifdef CY_DEBUG
aprint_debug_dev(sc->sc_dev, "port %d tx service\n",
cy->cy_port_num);
#endif
/* stop transmitting if no tty or CY_F_STOP set */
tp = cy->cy_tty;
if (tp == NULL || ISSET(cy->cy_flags, CY_F_STOP))
goto txdone;
count = 0;
if (ISSET(cy->cy_flags, CY_F_SEND_NUL)) {
cd_write_reg(sc, cy->cy_chip, CD1400_TDR, 0);
cd_write_reg(sc, cy->cy_chip, CD1400_TDR, 0);
count += 2;
CLR(cy->cy_flags, CY_F_SEND_NUL);
}
if (tp->t_outq.c_cc > 0) {
SET(tp->t_state, TS_BUSY);
while (tp->t_outq.c_cc > 0 &&
count < CD1400_TX_FIFO_SIZE) {
ch = getc(&tp->t_outq);
/*
* remember to double NUL characters
* because embedded transmit commands
* are enabled
*/
if (ch == 0) {
if (count >= CD1400_TX_FIFO_SIZE - 2) {
SET(cy->cy_flags, CY_F_SEND_NUL);
break;
}
cd_write_reg(sc, cy->cy_chip,
CD1400_TDR, ch);
count++;
}
cd_write_reg(sc, cy->cy_chip,
CD1400_TDR, ch);
count++;
}
} else {
/*
* no data to send -- check if we should
* start/stop a break
*/
/*
* XXX does this cause too much delay before
* breaks?
*/
if (ISSET(cy->cy_flags, CY_F_START_BREAK)) {
cd_write_reg(sc, cy->cy_chip,
CD1400_TDR, 0);
cd_write_reg(sc, cy->cy_chip,
CD1400_TDR, 0x81);
CLR(cy->cy_flags, CY_F_START_BREAK);
}
if (ISSET(cy->cy_flags, CY_F_END_BREAK)) {
cd_write_reg(sc, cy->cy_chip,
CD1400_TDR, 0);
cd_write_reg(sc, cy->cy_chip,
CD1400_TDR, 0x83);
CLR(cy->cy_flags, CY_F_END_BREAK);
}
}
if (tp->t_outq.c_cc == 0) {
txdone:
/*
* No data to send or requested to stop.
* Disable transmit interrupt
*/
cd_write_reg(sc, cy->cy_chip, CD1400_SRER,
cd_read_reg(sc, cy->cy_chip, CD1400_SRER)
& ~CD1400_SRER_TXRDY);
CLR(cy->cy_flags, CY_F_STOP);
CLR(tp->t_state, TS_BUSY);
}
if (tp->t_outq.c_cc <= tp->t_lowat) {
SET(cy->cy_flags, CY_F_START);
cy_events = 1;
}
/* terminate service context */
cd_write_reg(sc, cy->cy_chip, CD1400_TIR, save_tir & 0x3f);
cd_write_reg(sc, cy->cy_chip, CD1400_CAR, save_car);
int_serviced = 1;
} /* if (tx_service...) */
} /* for(...all CD1400s on a card) */
/* ensure an edge for next interrupt */
bus_space_write_1(sc->sc_memt, sc->sc_bsh,
CY_CLEAR_INTR << sc->sc_bustype, 0);
return int_serviced;
}
/*
* subroutine to enable CD1400 transmitter
*/
void
cy_enable_transmitter(struct cy_softc *sc, struct cy_port *cy)
{
int s = spltty();
cd_write_reg(sc, cy->cy_chip, CD1400_CAR,
cy->cy_port_num & CD1400_CAR_CHAN);
cd_write_reg(sc, cy->cy_chip, CD1400_SRER,
cd_read_reg(sc, cy->cy_chip, CD1400_SRER) | CD1400_SRER_TXRDY);
splx(s);
}
/*
* Execute a CD1400 channel command
*/
void
cd1400_channel_cmd(struct cy_softc *sc, struct cy_port *cy, int cmd)
{
u_int waitcnt = 5 * 8 * 1024; /* approx 5 ms */
#ifdef CY_DEBUG
printf("c1400_channel_cmd cy %p command 0x%x\n", cy, cmd);
#endif
/* wait until cd1400 is ready to process a new command */
while (cd_read_reg(sc, cy->cy_chip, CD1400_CCR) != 0 && waitcnt-- > 0);
if (waitcnt == 0)
log(LOG_ERR, "%s: channel command timeout\n",
device_xname(sc->sc_dev));
cd_write_reg(sc, cy->cy_chip, CD1400_CCR, cmd);
}
/*
* Compute clock option register and baud rate register values
* for a given speed. Return 0 on success, -1 on failure.
*
* The error between requested and actual speed seems
* to be well within allowed limits (less than 3%)
* with every speed value between 50 and 150000 bps.
*/
int
cy_speed(speed_t speed, int *cor, int *bpr, int cy_clock)
{
int c, co, br;
if (speed < 50 || speed > 150000)
return -1;
for (c = 0, co = 8; co <= 2048; co <<= 2, c++) {
br = (cy_clock + (co * speed) / 2) / (co * speed);
if (br < 0x100) {
*bpr = br;
*cor = c;
return 0;
}
}
return -1;
}