NetBSD-5.0.2/sys/dev/ic/ns8477reg.h
/* $NetBSD: ns8477reg.h,v 1.3 2008/04/28 20:23:50 martin Exp $ */
/*-
* Copyright (c) 1998 The NetBSD Foundation, Inc.
* All rights reserved.
*
* This code is derived from software contributed to The NetBSD Foundation
* by Christos Zoulas.
*
* Redistribution and use in source and binary forms, with or without
* modification, are permitted provided that the following conditions
* are met:
* 1. Redistributions of source code must retain the above copyright
* notice, this list of conditions and the following disclaimer.
* 2. Redistributions in binary form must reproduce the above copyright
* notice, this list of conditions and the following disclaimer in the
* documentation and/or other materials provided with the distribution.
*
* THIS SOFTWARE IS PROVIDED BY THE NETBSD FOUNDATION, INC. AND CONTRIBUTORS
* ``AS IS'' AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED
* TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR
* PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE FOUNDATION OR CONTRIBUTORS
* BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR
* CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF
* SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS
* INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN
* CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE)
* ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
* POSSIBILITY OF SUCH DAMAGE.
*/
/*
* Register descriptions of the National Semiconductor PC8477B
* floppy controller
*/
#define FDC_SRA 0 /* (R) Status Register A */
#define FDC_SRB 1 /* (R) Status Register B */
#define FDC_DOR 2 /* (R/W) Digital Output Register */
# define FDC_DOR_SEL0 0x01 /* Drive Select 0 */
# define FDC_DOR_SEL1 0x02 /* Drive Select 1 */
# define FDC_DOR_RESET 0x04 /* Reset Controller */
# define FDC_DOR_DMAEN 0x08 /* Dma Enable */
# define FDC_DOR_MTR0 0x10 /* Motor Enable 0 */
# define FDC_DOR_MTR1 0x20 /* Motor Enable 1 */
# define FDC_DOR_MTR2 0x40 /* Motor Enable 2 */
# define FDC_DOR_MTR3 0x80 /* Motor Enable 3 */
# define FDC_DOR_MTR(a) (1 << (n + 4))
#define FDC_TDR 3 /* (R/W) Tape Drive Register */
# define FDC_TDR_SEL0 0x01 /* Tape Select 0 */
# define FDC_TDR_SEL1 0x02 /* Tape Select 1 */
#define FDC_MSR 4 /* (R) Main Status Register */
# define FDC_MSR_BUSY0 0x01 /* Drive 0 Busy */
# define FDC_MSR_BUSY1 0x02 /* Drive 1 Busy */
# define FDC_MSR_BUSY2 0x04 /* Drive 2 Busy */
# define FDC_MSR_BUSY3 0x08 /* Drive 3 Busy */
# define FDC_MSR_CMDPRG 0x10 /* Command In Progress */
# define FDC_MSR_NONDMA 0x20 /* Non DMA Execution */
# define FDC_MSR_DIO 0x40 /* Data I/O Direction */
# define FDC_MSR_RQM 0x80 /* Reguest for Master */
#define FDC_DSR 4 /* (W) Data Rate Select Register */
# define FDC_DSR_DRATE0 0x01 /* Data Rate Select 0 */
# define FDC_DSR_DRATE1 0x02 /* Data Rate Select 0 */
/*
* bit MFM FM
* 00 500Kb/s 250Kb/s
* 01 300Kb/s 150Kb/s
* 10 250Kb/s 125Kb/s
* 11 1Mb/s illegal
*/
# define FDC_DSR_500KBPS 0x00 /* 500KBPS MFM drive transfer rate */
# define FDC_DSR_300KBPS 0x01 /* 300KBPS MFM drive transfer rate */
# define FDC_DSR_250KBPS 0x02 /* 250KBPS MFM drive transfer rate */
# define FDC_DSR_1MBPS 0x03 /* 1MBPS MFM drive transfer rate */
# define FDC_DSR_PREC0 0x04 /* Precompensation bit 0*/
# define FDC_DSR_PREC1 0x08 /* Precompensation bit 1*/
# define FDC_DSR_PREC2 0x10 /* Precompensation bit 2*/
/*
* bit Precomp Data Rate
* 000 default
* 001 41.7ns 1Mb/s
* 010 83.3ns
* 011 125.0ns 500Kb/s, 300Kb/s, 250Kb/s
* 100 168.7ns
* 101 208.3ns
* 110 208.3ns
* 111 0.0ns
*/
# define FDC_DSR_ZERO 0x20 /* Undef; should be 0 */
# define FDC_DSR_LOWPWR 0x40 /* Low Power Mode */
# define FDC_DSR_SWRST 0x80 /* Software Reset */
#define FDC_FIFO 5 /* (R/W) Data Register (FIFO) */
/*
* Commands
*/
#define FDC_CMD_MODE (0x01)
#define FDC_CMD_READ_TRACK(mfm) (0x02|mfm)
#define FDC_CMD_SPECIFY (0x03)
#define FDC_CMD_SENSE_DRIVE_STATUS (0x04)
#define FDC_CMD_WRITE_DATA(mt,mfm) (0x05|mt|mfm)
#define FDC_CMD_READ_DATA(mt,mfm,sk) (0x06|mt|mfm|sk)
#define FDC_CMD_RECALIBRATE (0x07)
#define FDC_CMD_SENSE_INTERRUPT (0x08)
#define FDC_CMD_WRITE_DEL_DATA(mt,mfm) (0x09|mt|mfm)
#define FDC_CMD_READ_ID(mfm) (0x0a|mfm)
#define FDC_CMD_READ_DEL_DATA(mt,mfm,sk) (0x0c|mt|mfm|sk)
#define FDC_CMD_FORMAT_TRACK(mfm) (0x0d|mfm)
#define FDC_CMD_DUMPREG (0x0e)
#define FDC_CMD_SEEK (0x0f)
#define FDC_CMD_VERSION (0x10)
#define FDC_CMD_SCAN_EQUAL(mt,mfm,sk) (0x11|mt|mfm|sk)
#define FDC_CMD_PERPENDICULAR (0x12)
#define FDC_CMD_CONFIGURE (0x13)
#define FDC_CMD_LOCK(lock) (0x14|lock)
#define FDC_CMD_VERIFY(mt,mfm,sk) (0x16|mt|mfm|sk)
#define FDC_CMD_NSC (0x18)
#define FDC_CMD_SCAN_LO_EQUAL(mt,mfm,sk) (0x19|mt|mfm|sk)
#define FDC_CMD_SCAN_HI_EQUAL(mt,mfm,sk) (0x1d|mt|mfm|sk)
#define FDC_CMD_SET_TRACK(wnr) (0x21|wnr)
#define FDC_CMD_REL_SEEK(dir) (0x8f|dir)
#define FDC_CMD_CONFIGURE_FLAGS_POLL 0x10
#define FDC_CMD_CONFIGURE_FLAGS_FIFO 0x20
#define FDC_CMD_CONFIGURE_FLAGS_EIS 0x40
#define FDC_CMD_FLAGS_LOCK 0x80
#define FDC_CMD_FLAGS_MT 0x80
#define FDC_CMD_FLAGS_MFM 0x40
#define FDC_CMD_FLAGS_SK 0x20
#define FDC_CMD_FLAGS_DIR 0x40
#define FDC_CMD_FLAGS_WNR 0x40
/*
* Command Status
*/
/* Status register ST0 */
#define FDC_ST0BITS "\020\010invld\007abnrml\006seek_cmplt\005drv_chck\004drive_rdy\003top_head\002ds1\001ds0"
# define FDC_ST0_DS0 0x01 /* Drive Select 0 */
# define FDC_ST0_DS1 0x02 /* Drive Select 1 */
# define FDC_ST0_HDS 0x04 /* Head select */
# define FDC_ST0_ZERO 0x08 /* Undef; should be 0 */
# define FDC_ST0_EC 0x10 /* Equipment check */
# define FDC_ST0_SE 0x20 /* Seek completed */
# define FDC_ST0_IC0 0x40 /* Interrupt code 0 */
# define FDC_ST0_IC1 0x80 /* Interrupt code 1 */
# define FDC_ST0(a) (a & ~(FDC_ST0_DS0|FDC_ST0_DS1|FDC_ST0_HDS))
# define FDC_ST0_NRML 0x00 /* Normal Completion */
# define FDC_ST0_ABNR 0x40 /* Abnormal Termination */
# define FDC_ST0_INVL 0x80 /* Invalid Command */
# define FDC_ST0_CHGD 0xc0 /* Drive status changed */
/* Status register ST1 */
#define FDC_ST1BITS "\020\010end_of_cyl\006bad_crc\005data_overrun\003sec_not_fnd\002write_protect\001no_am"
# define FDC_ST1_MA 0x01 /* Missing address mark */
# define FDC_ST1_NW 0x02 /* Write Protect */
# define FDC_ST1_ND 0x04 /* No Data */
# define FDC_ST1_ZERO0 0x08 /* Undef; should be 0 */
# define FDC_ST1_OR 0x10 /* Overrun error */
# define FDC_ST1_CE 0x20 /* CRC error */
# define FDC_ST1_ZERO1 0x40 /* Undef; should be 0 */
# define FDC_ST1_ET 0x80 /* End of Track */
/* Status register ST2 */
#define FDC_ST2BITS "\020\007ctrl_mrk\006bad_crc\005wrong_cyl\004scn_eq\003scn_not_fnd\002bad_cyl\001no_dam"
# define FDC_ST2_MD 0x01 /* Missing Address Mark */
# define FDC_ST2_BT 0x02 /* Bad Track */
# define FDC_ST2_SNS 0x04 /* Scan Not Satisfied */
# define FDC_ST2_SEH 0x08 /* Scan Equal Hit */
# define FDC_ST2_WT 0x10 /* Wrong Track */
# define FDC_ST2_CD 0x20 /* CRC Error in Data */
# define FDC_ST2_CM 0x40 /* Control Mark */
# define FDC_ST2_ZERO 0x80 /* Undef; should be 0 */
/* Status register ST3 */
#define FDC_ST3BITS "\020\010fault\007write_protect\006drdy\005tk0\004two_side\003side_sel\002ds1\001ds0"
# define FDC_ST3_DS0 0x01 /* Drive Select 0 */
# define FDC_ST3_DS1 0x02 /* Drive Select 1 */
# define FDC_ST3_HDS 0x04 /* Head Select */
# define FDC_ST3_ONE0 0x08 /* Undef; should be 0 */
# define FDC_ST3_TK0 0x10 /* Track 0 */
# define FDC_ST3_ONE1 0x20 /* Undef; should be 0 */
# define FDC_ST3_WP 0x40 /* Write Protect */
# define FDC_ST3_ZERO 0x80 /* Undef; should be 0 */
#define FDC_NONE 6 /* (X) None (Bus TRI-STATE) */
#define FDC_DIR 7 /* (R) Digital Input Register */
# define FDC_DIR_DSKCHG 0x80 /* Disk Changed */
#define FDC_CCR 7 /* (W) Configuration Register */
# define FDC_CCR_DRATE0 0x01 /* Data Rate Select 0 */
# define FDC_CCR_DRATE1 0x02 /* Data Rate Select 0 */
# define FDC_CCR_ZERO0 0x04 /* Undef; should be 0 */
# define FDC_CCR_ZERO1 0x08 /* Undef; should be 0 */
# define FDC_CCR_ZERO2 0x10 /* Undef; should be 0 */
# define FDC_CCR_ZERO3 0x20 /* Undef; should be 0 */
# define FDC_CCR_ZERO4 0x40 /* Undef; should be 0 */
# define FDC_CCR_ZERO5 0x80 /* Undef; should be 0 */
#define FDC_NPORT 8