NetBSD-5.0.2/sys/dev/isa/i82365_isasubr.c
/* $NetBSD: i82365_isasubr.c,v 1.40 2008/04/08 20:08:49 cegger Exp $ */
/*
* Copyright (c) 2000 Christian E. Hopps. All rights reserved.
* Copyright (c) 1998 Bill Sommerfeld. All rights reserved.
* Copyright (c) 1997 Marc Horowitz. All rights reserved.
*
* Redistribution and use in source and binary forms, with or without
* modification, are permitted provided that the following conditions
* are met:
* 1. Redistributions of source code must retain the above copyright
* notice, this list of conditions and the following disclaimer.
* 2. Redistributions in binary form must reproduce the above copyright
* notice, this list of conditions and the following disclaimer in the
* documentation and/or other materials provided with the distribution.
* 3. All advertising materials mentioning features or use of this software
* must display the following acknowledgement:
* This product includes software developed by Marc Horowitz.
* 4. The name of the author may not be used to endorse or promote products
* derived from this software without specific prior written permission.
*
* THIS SOFTWARE IS PROVIDED BY THE AUTHOR ``AS IS'' AND ANY EXPRESS OR
* IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES
* OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED.
* IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT, INDIRECT,
* INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT
* NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE,
* DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY
* THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
* (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF
* THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
*/
#include <sys/cdefs.h>
__KERNEL_RCSID(0, "$NetBSD: i82365_isasubr.c,v 1.40 2008/04/08 20:08:49 cegger Exp $");
#define PCICISADEBUG
#include <sys/param.h>
#include <sys/systm.h>
#include <sys/device.h>
#include <sys/extent.h>
#include <sys/malloc.h>
#include <sys/bus.h>
#include <sys/intr.h>
#include <dev/isa/isareg.h>
#include <dev/isa/isavar.h>
#include <dev/pcmcia/pcmciareg.h>
#include <dev/pcmcia/pcmciavar.h>
#include <dev/pcmcia/pcmciachip.h>
#include <dev/ic/i82365reg.h>
#include <dev/ic/i82365var.h>
#include <dev/isa/i82365_isavar.h>
/*****************************************************************************
* Configurable parameters.
*****************************************************************************/
#include "opt_pcic_isa_alloc_iobase.h"
#include "opt_pcic_isa_alloc_iosize.h"
#include "opt_pcic_isa_intr_alloc_mask.h"
/*
* Default I/O allocation range. If both are set to non-zero, these
* values will be used instead. Otherwise, the code attempts to probe
* the bus width. Systems with 10 address bits should use 0x300 and 0xff.
* Systems with 12 address bits (most) should use 0x400 and 0xbff.
*/
#ifndef PCIC_ISA_ALLOC_IOBASE
#define PCIC_ISA_ALLOC_IOBASE 0
#endif
#ifndef PCIC_ISA_ALLOC_IOSIZE
#define PCIC_ISA_ALLOC_IOSIZE 0
#endif
int pcic_isa_alloc_iobase = PCIC_ISA_ALLOC_IOBASE;
int pcic_isa_alloc_iosize = PCIC_ISA_ALLOC_IOSIZE;
/*
* Default IRQ allocation bitmask. This defines the range of allowable
* IRQs for PCMCIA slots. Useful if order of probing would screw up other
* devices, or if PCIC hardware/cards have trouble with certain interrupt
* lines.
*/
#ifndef PCIC_ISA_INTR_ALLOC_MASK
#define PCIC_ISA_INTR_ALLOC_MASK 0xffff
#endif
int pcic_isa_intr_alloc_mask = PCIC_ISA_INTR_ALLOC_MASK;
#ifndef PCIC_IRQ_PROBE
#ifdef hpcmips
/*
* The irq probing doesn't work with current vrisab implementation.
* The irq is just an key to find matching GPIO port to use and is fixed.
*/
#define PCIC_IRQ_PROBE 0
#else
#define PCIC_IRQ_PROBE 1
#endif
#endif
int pcic_irq_probe = PCIC_IRQ_PROBE;
/*****************************************************************************
* End of configurable parameters.
*****************************************************************************/
#ifdef PCICISADEBUG
int pcicsubr_debug = 0;
#define DPRINTF(arg) do { if (pcicsubr_debug) printf arg ; } while (0)
#else
#define DPRINTF(arg)
#endif
/*
* count the interrupt if we have a status set
* just use socket 0
*/
void pcic_isa_probe_interrupts(struct pcic_softc *, struct pcic_handle *);
static int pcic_isa_count_intr(void *);
static int
pcic_isa_count_intr(arg)
void *arg;
{
struct pcic_softc *sc;
struct pcic_isa_softc *isc;
struct pcic_handle *h;
int cscreg;
h = arg;
sc = (struct pcic_softc *)h->ph_parent;
isc = (struct pcic_isa_softc *)h->ph_parent;
cscreg = pcic_read(h, PCIC_CSC);
if (cscreg & PCIC_CSC_CD) {
if ((++sc->intr_detect % 20) == 0)
printf(".");
else
DPRINTF(("."));
return (1);
}
/*
* make sure we don't get stuck in a loop due to
* unhandled level interrupts
*/
if (++sc->intr_false > 40) {
isa_intr_disestablish(isc->sc_ic, sc->ih);
sc->ih = 0;
pcic_write(h, PCIC_CSC_INTR, 0);
delay(10);
}
#ifdef PCICISADEBUG
if (cscreg)
DPRINTF(("o"));
else
DPRINTF(("X"));
#endif
return (cscreg ? 1 : 0);
}
/*
* use soft interrupt card detect to find out which irqs are available
* for this controller
*/
void
pcic_isa_probe_interrupts(sc, h)
struct pcic_softc *sc;
struct pcic_handle *h;
{
struct pcic_isa_softc *isc = (void *) sc;
isa_chipset_tag_t ic;
int i, j, mask, irq;
int cd, cscintr, intr, csc;
ic = isc->sc_ic;
printf("%s: controller %d detecting irqs with mask 0x%04x:",
device_xname(&sc->dev), h->chip, sc->intr_mask[h->chip]);
DPRINTF(("\n"));
/* clear any current interrupt */
pcic_read(h, PCIC_CSC);
/* first disable the status irq, card detect is enabled later */
pcic_write(h, PCIC_CSC_INTR, 0);
/* steer the interrupt to isa and disable ring and interrupt */
intr = pcic_read(h, PCIC_INTR);
DPRINTF(("pcic: old intr 0x%x\n", intr));
intr &= ~(PCIC_INTR_RI_ENABLE | PCIC_INTR_ENABLE | PCIC_INTR_IRQ_MASK);
pcic_write(h, PCIC_INTR, intr);
/* clear any current interrupt */
pcic_read(h, PCIC_CSC);
cd = pcic_read(h, PCIC_CARD_DETECT);
cd |= PCIC_CARD_DETECT_SW_INTR;
mask = 0;
for (i = 0; i < 16; i++) {
/* honor configured limitations */
if ((sc->intr_mask[h->chip] & (1 << i)) == 0)
continue;
DPRINTF(("probing irq %d: ", i));
/* ask for a pulse interrupt so we don't share */
if (isa_intr_alloc(ic, (1 << i), IST_PULSE, &irq)) {
DPRINTF(("currently allocated\n"));
continue;
}
cscintr = PCIC_CSC_INTR_CD_ENABLE;
cscintr |= (irq << PCIC_CSC_INTR_IRQ_SHIFT);
pcic_write(h, PCIC_CSC_INTR, cscintr);
delay(10);
/* Clear any pending interrupt. */
(void) pcic_read(h, PCIC_CSC);
if ((sc->ih = isa_intr_establish(ic, irq, IST_EDGE, IPL_TTY,
pcic_isa_count_intr, h)) == NULL)
panic("cant get interrupt");
/* interrupt 40 times */
sc->intr_detect = 0;
for (j = 0; j < 40 && sc->ih; j++) {
sc->intr_false = 0;
pcic_write(h, PCIC_CARD_DETECT, cd);
delay(100);
csc = pcic_read(h, PCIC_CSC);
DPRINTF(("%s", csc ? "-" : ""));
}
DPRINTF((" total %d\n", sc->intr_detect));
/* allow for misses */
if (sc->intr_detect > 37 && sc->intr_detect <= 40) {
printf("%d", i);
DPRINTF((" succeded\n"));
mask |= (1 << i);
}
if (sc->ih) {
isa_intr_disestablish(ic, sc->ih);
sc->ih = 0;
pcic_write(h, PCIC_CSC_INTR, 0);
delay(10);
}
}
sc->intr_mask[h->chip] = mask;
printf("%s\n", sc->intr_mask[h->chip] ? "" : " none");
}
/*
* called with interrupts enabled, light up the irqs to find out
* which irq lines are actually hooked up to our pcic
*/
void
pcic_isa_config_interrupts(self)
struct device *self;
{
struct pcic_softc *sc;
struct pcic_isa_softc *isc;
struct pcic_handle *h;
isa_chipset_tag_t ic;
int s, i, chipmask, chipuniq;
sc = (struct pcic_softc *) self;
isc = (struct pcic_isa_softc *) self;
ic = isc->sc_ic;
/* probe each controller */
chipmask = 0xffff;
for (i = 0; i < PCIC_NSLOTS; i += 2) {
if (sc->handle[i].flags & PCIC_FLAG_SOCKETP)
h = &sc->handle[i];
else if (sc->handle[i + 1].flags & PCIC_FLAG_SOCKETP)
h = &sc->handle[i + 1];
else
continue;
sc->intr_mask[h->chip] =
PCIC_INTR_IRQ_VALIDMASK & pcic_isa_intr_alloc_mask;
/* the cirrus chips lack support for the soft interrupt */
if (pcic_irq_probe != 0 &&
h->vendor != PCIC_VENDOR_CIRRUS_PD67XX)
pcic_isa_probe_interrupts(sc, h);
chipmask &= sc->intr_mask[h->chip];
}
/* now see if there is at least one irq per chip not shared by all */
chipuniq = 1;
for (i = 0; i < PCIC_NSLOTS; i += 2) {
if ((sc->handle[i].flags & PCIC_FLAG_SOCKETP) == 0 &&
(sc->handle[i + 1].flags & PCIC_FLAG_SOCKETP) == 0)
continue;
if ((sc->intr_mask[i / 2] & ~chipmask) == 0) {
chipuniq = 0;
break;
}
}
/*
* the rest of the following code used to run at config time with
* no interrupts and gets unhappy if this is violated so...
*/
s = splhigh();
/*
* allocate our irq. it will be used by both controllers. I could
* use two different interrupts, but interrupts are relatively
* scarce, shareable, and for PCIC controllers, very infrequent.
*/
if ((device_cfdata(self)->cf_flags & 1) == 0) {
if (sc->irq != ISA_UNKNOWN_IRQ) {
if ((chipmask & (1 << sc->irq)) == 0)
printf("%s: warning: configured irq %d not "
"detected as available\n",
device_xname(&sc->dev), sc->irq);
} else if (chipmask == 0 ||
isa_intr_alloc(ic, chipmask, IST_EDGE, &sc->irq)) {
aprint_error_dev(&sc->dev, "no available irq; ");
sc->irq = ISA_UNKNOWN_IRQ;
} else if ((chipmask & ~(1 << sc->irq)) == 0 && chipuniq == 0) {
aprint_error_dev(&sc->dev, "can't share irq with cards; ");
sc->irq = ISA_UNKNOWN_IRQ;
}
} else {
printf("%s: ", device_xname(&sc->dev));
sc->irq = ISA_UNKNOWN_IRQ;
}
if (sc->irq != ISA_UNKNOWN_IRQ) {
sc->ih = isa_intr_establish(ic, sc->irq, IST_EDGE, IPL_TTY,
pcic_intr, sc);
if (sc->ih == NULL) {
aprint_error_dev(&sc->dev, "can't establish interrupt");
sc->irq = ISA_UNKNOWN_IRQ;
}
}
if (sc->irq == ISA_UNKNOWN_IRQ)
printf("polling for socket events\n");
else
printf("%s: using irq %d for socket events\n", device_xname(&sc->dev),
sc->irq);
pcic_attach_sockets_finish(sc);
splx(s);
}
/*
* XXX This routine does not deal with the aliasing issue that its
* trying to.
*
* Any isa device may be decoding only 10 bits of address including
* the pcic. This routine only detects if the pcic is doing 10 bits.
*
* What should be done is detect the pcic's idea of the bus width,
* and then within those limits allocate a sparse map, where the
* each sub region is offset by 0x400.
*/
void pcic_isa_bus_width_probe (sc, iot, ioh, base, length)
struct pcic_softc *sc;
bus_space_tag_t iot;
bus_space_handle_t ioh;
bus_addr_t base;
u_int32_t length;
{
bus_space_handle_t ioh_high;
int i, iobuswidth, tmp1, tmp2;
/*
* figure out how wide the isa bus is. Do this by checking if the
* pcic controller is mirrored 0x400 above where we expect it to be.
*/
iobuswidth = 12;
/* Map i/o space. */
if (bus_space_map(iot, base + 0x400, length, 0, &ioh_high)) {
aprint_error_dev(&sc->dev, "can't map high i/o space\n");
return;
}
for (i = 0; i < PCIC_NSLOTS; i++) {
if (sc->handle[i].flags & PCIC_FLAG_SOCKETP) {
/*
* read the ident flags from the normal space and
* from the mirror, and compare them
*/
bus_space_write_1(iot, ioh, PCIC_REG_INDEX,
sc->handle[i].sock + PCIC_IDENT);
tmp1 = bus_space_read_1(iot, ioh, PCIC_REG_DATA);
bus_space_write_1(iot, ioh_high, PCIC_REG_INDEX,
sc->handle[i].sock + PCIC_IDENT);
tmp2 = bus_space_read_1(iot, ioh_high, PCIC_REG_DATA);
if (tmp1 == tmp2)
iobuswidth = 10;
}
}
bus_space_free(iot, ioh_high, length);
/*
* XXX some hardware doesn't seem to grok addresses in 0x400 range--
* apparently missing a bit or more of address lines. (e.g.
* CIRRUS_PD672X with Linksys EthernetCard ne2000 clone in TI
* TravelMate 5000--not clear which is at fault)
*
* Add a kludge to detect 10 bit wide buses and deal with them,
* and also a config file option to override the probe.
*/
if (iobuswidth == 10) {
sc->iobase = 0x300;
sc->iosize = 0x0ff;
} else {
sc->iobase = 0x400;
sc->iosize = 0xbff;
}
DPRINTF(("%s: bus_space_alloc range 0x%04lx-0x%04lx (probed)\n",
device_xname(&sc->dev), (long) sc->iobase,
(long) sc->iobase + sc->iosize));
if (pcic_isa_alloc_iobase && pcic_isa_alloc_iosize) {
sc->iobase = pcic_isa_alloc_iobase;
sc->iosize = pcic_isa_alloc_iosize;
DPRINTF(("%s: bus_space_alloc range 0x%04lx-0x%04lx "
"(config override)\n", device_xname(&sc->dev), (long) sc->iobase,
(long) sc->iobase + sc->iosize));
}
}
void *
pcic_isa_chip_intr_establish(pch, pf, ipl, fct, arg)
pcmcia_chipset_handle_t pch;
struct pcmcia_function *pf;
int ipl;
int (*fct)(void *);
void *arg;
{
struct pcic_handle *h = (struct pcic_handle *) pch;
struct pcic_softc *sc = (struct pcic_softc *)(h->ph_parent);
struct pcic_isa_softc *isc = (struct pcic_isa_softc *)(h->ph_parent);
isa_chipset_tag_t ic = isc->sc_ic;
int irq, ist;
void *ih;
int reg;
/*
* PLEASE NOTE:
* The IRQLEVEL bit has no bearing on what happens on the host side of
* the PCMCIA controller. ISA interrupts are defined to be edge-
* triggered, and as this attachment is for ISA devices, the interrupt
* *must* be configured for edge-trigger. If you think you should
* change this to use IST_LEVEL, you are *wrong*. You should figure
* out what your real problem is and leave this code alone rather than
* breaking everyone else's systems. - mycroft
*/
if (pf->cfe->flags & PCMCIA_CFE_IRQLEVEL)
ist = IST_EDGE; /* SEE COMMENT ABOVE */
else if (pf->cfe->flags & PCMCIA_CFE_IRQPULSE)
ist = IST_PULSE; /* SEE COMMENT ABOVE */
else
ist = IST_EDGE; /* SEE COMMENT ABOVE */
if (isa_intr_alloc(ic, sc->intr_mask[h->chip], ist, &irq))
return (NULL);
h->ih_irq = irq;
if (h->flags & PCIC_FLAG_ENABLED) {
reg = pcic_read(h, PCIC_INTR);
reg &= ~PCIC_INTR_IRQ_MASK;
pcic_write(h, PCIC_INTR, reg | irq);
}
if ((ih = isa_intr_establish(ic, irq, ist, ipl, fct, arg)) == NULL)
return (NULL);
printf("%s: card irq %d\n", device_xname(h->pcmcia), irq);
return (ih);
}
void
pcic_isa_chip_intr_disestablish(pch, ih)
pcmcia_chipset_handle_t pch;
void *ih;
{
struct pcic_handle *h = (struct pcic_handle *) pch;
struct pcic_isa_softc *isc = (struct pcic_isa_softc *)(h->ph_parent);
isa_chipset_tag_t ic = isc->sc_ic;
int reg;
isa_intr_disestablish(ic, ih);
h->ih_irq = 0;
if (h->flags & PCIC_FLAG_ENABLED) {
reg = pcic_read(h, PCIC_INTR);
reg &= ~PCIC_INTR_IRQ_MASK;
pcic_write(h, PCIC_INTR, reg);
}
}