NetBSD-5.0.2/sys/dev/pci/btvmeireg.h
/* $NetBSD: btvmeireg.h,v 1.5 2005/12/11 12:22:48 christos Exp $ */
#ifndef _bit3reg_h_
#define _bit3reg_h_
#ifdef _KERNEL
#define BIT3_LSR_BITS "\20\1CABLE\2LRCERR\3ITO\6INTPR\7RBERR\10PARERR"
/* following is from:
** Filename: btpciio.h
**
** Purpose: Bit 3 400-809 PCI Applications Toolkit
** Adaptor Node Register Include File.
*/
/******************************************************************************
**
** Mapping Register Defines
**
******************************************************************************/
#define MR_PCI_VME 0x0 /* PCI to VME Map RAM base offset */
#define MR_PCI_VME_SIZE 0x8000 /* PCI to VME Map RAM size (bytes) */
#define MR_VME_PCI 0x8000 /* VME to PCI Map RAM base offset */
#define MR_VME_PCI_SIZE 0x4000 /* VME to PCI Map RAM size (bytes) */
#define MR_DMA_PCI 0xC000 /* DMA to PCI Map RAM base offset */
#define MR_DMA_PCI_SIZE 0x4000 /* DMA to PCI Map RAM size (bytes) */
#define MR_BYTE_SWAP (1<<3) /* r/w, Byte swap bytes */
#define MR_WORD_SWAP (1<<2) /* r/w, Swap words */
#define MR_WBYTE_SWAP (1<<1) /* r/w, Byte Swap non-bytes */
#define MR_RAM_INVALID (1<<0) /* r/w, Map register is invalid */
#define MR_ADDR_MASK 0xFFFFF000UL /* Mask for map address bits A31-A12 */
#define MR_REM_BUS_MASK 0x00000FFFUL /* Mask for remote address bits A11-A0 */
#define MR_AMOD_MASK 0x00000FC0UL /* Mask for address modifier bits */
/* AM5-AM0 for register bits A11-A6 */
#define MR_AMOD_SHIFT 6 /* Shift value for AMOD bits AM5-AM0 */
#define MR_FC_MASK 0x30 /* Mask for Mapping RAM Function Codes */
#define MR_FC_RBIO 0x10 /* Remote Bus I/O Mapping function code */
#define MR_FC_RRAM 0x20 /* Remote RAM Mapping function code */
#define MR_FC_DPRAM 0x30 /* Dual Port RAM Mapping function code */
/******************************************************************************
**
** Local Adaptor Node Registers
**
*******************************************************************************
**
** Local Command Register (Read/Write, 8 Bits)
**
*******************************************************************************
** 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0
** +C_STAT |+CLR_PR |+SND_PT | | | | |
******************************************************************************/
#define LOC_CMD1 (0x00) /* Local Command Register */
#define LC1_CLR_ERROR (1<<7) /* w, Clear status error bits (1 Shot) */
#define LC1_CLR_PR_INT (1<<6) /* w, Clear PR (PS) Interrupt (1 Shot) */
#define LC1_SND_PT_INT (1<<5) /* r/w, Set PT Interrupt */
/******************************************************************************
**
** Local Interrupt Control Register (Read/Write, 8 Bits)
**
*******************************************************************************
** 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0
** +INT_ACT | +INT_EN |+ERR_INT | 0 | 0 | +CINT2 | +CINT1 | +CINT0
******************************************************************************/
#define LOC_INT_CTRL (0x01) /* Local Interrupt Control Register */
#define LIC_INT_PENDING (1<<7) /* r , Adaptor asserting INT on PCI bus */
#define LIC_INT_ENABLE (1<<6) /* r/w, Normal (PR & CINT) INT Enable */
#define LIC_ERR_INT_ENABLE (1<<5) /* r/w, Error Interrupt Enable */
#define LIC_PT_CINT_SEL2 (1<<2) /* r/w, PT CINT Line Selection Bit 2 */
#define LIC_PT_CINT_SEL1 (1<<1) /* r/w, PT CINT Line Selection Bit 1 */
#define LIC_PT_CINT_SEL0 (1<<0) /* r/w, PT CINT Line Selection Bit 0 */
/******************************************************************************
**
** Local Status Register (Read Only, 8 Bits)
**
*******************************************************************************
** 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0
** +PARITY |+REMBUS |+PR_INT |+CARD_RDY| 0 |+TIMEOUT|+LRC_ERR|+NOCONNECT
******************************************************************************/
#define LOC_STATUS (0x02) /* Local Status Register */
#define LSR_PARITY_ERR (1<<7) /* Interface Parity Error PCI->REM. */
#define LSR_REMBUS_ERR (1<<6) /* BERR from VME on PCI->REM. xfer */
#define LSR_PR_STATUS (1<<5) /* PR interrupt received from REMOTE */
#define LSR_TIMEOUT_ERR (1<<2) /* Interface Timeout error PCI->REM */
#define LSR_LRC_ERR (1<<1) /* LRC error (DMA master only) */
#define LSR_NO_CONNECT (1<<0) /* REM. bus power or I/O cable is off */
#define LSR_ERROR_MASK (LSR_PARITY_ERR|LSR_REMBUS_ERR|LSR_TIMEOUT_ERR|LSR_LRC_ERR)
#define LSR_CERROR_MASK (LSR_NO_CONNECT|LSR_ERROR_MASK)
/******************************************************************************
**
** Local Interrupt Status Register (Read Only)
**
*******************************************************************************
** 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0
** +CINT7 | +CINT6 | +CINT5 | +CINT4 | +CINT3 | +CINT2 | +CINT1 | +CINT0
******************************************************************************/
#define LOC_INT_STATUS (0x03) /* Local Interrupt Status Register */
#define LIS_CINT7 (1<<7) /* Cable Interrupt 7 - CINT7 */
#define LIS_CINT6 (1<<6) /* Cable Interrupt 6 - CINT6 */
#define LIS_CINT5 (1<<5) /* Cable Interrupt 5 - CINT5 */
#define LIS_CINT4 (1<<4) /* Cable Interrupt 4 - CINT4 */
#define LIS_CINT3 (1<<3) /* Cable Interrupt 3 - CINT3 */
#define LIS_CINT2 (1<<2) /* Cable Interrupt 2 - CINT2 */
#define LIS_CINT1 (1<<1) /* Cable Interrupt 1 - CINT1 */
#define LIS_CINT_MASK (LIS_CINT1 | LIS_CINT2 | LIS_CINT3 | LIS_CINT4 | LIS_CINT5 | LIS_CINT6 | LIS_CINT7 )
/******************************************************************************
**
** Remote Adaptor Registers
**
*******************************************************************************
**
** Remote Command Register 1 (Write Only, 8 Bits)
**
*******************************************************************************
** 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 |
** +RESET |+CLR_PT | +SND_PR |+LOCKBUS| +PGMODE| +IACK2 | +IACK1 | +IACK0|VME
** " | " | " | " | " |+IOPGSEL|+PRMOD1 |+PRMOD0|Q-bus
** " | " | " | " | " |+IOPGSEL| 0 | 0 |MBus1
******************************************************************************/
#define REM_CMD1 (0x08) /* Remote Command Register 1 */
#define RC1_RESET_REM (1<<7) /* Reset remote bus - ONE SHOT */
#define RC1_CLR_PT_INT (1<<6) /* PT (PM) interrupt - FROM REMOTE */
#define RC1_SND_PR_INT (1<<5) /* PR (PS) interrupt - TO REMOTE */
#define RC1_LOCK_REM_BUS (1<<4) /* Lock remote bus - FOR RMW ONLY */
#define RC1_PG_SEL (1<<3) /* Enable page mode access */
#define RC1_INT_ACK_A3 (1<<2) /* IACK Read Mode Address Bit 2 */
#define RC1_INT_ACK_A2 (1<<1) /* IACK Read Mode Address Bit 1 */
#define RC1_INT_ACK_A1 (1<<0) /* IACK Read Mode Address Bit 0 */
#define RC1_IACK_MASK (0x07) /* IACK read level select mask */
/*****************************************************************************
**
** Remote Status Register (Read Only, 8 Bits)
**
******************************************************************************
** 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 |
** +RRESET | IACK_1 | +PRSET | +LKNSET| +PGREG |IACK_2|+PTSET|IACK_0|VME
** 0 | 0 | +PRSET | +LKNSET| +PGMOD | 0 |+PTSET| 0 |A24,Q,MB1
*****************************************************************************/
#define REM_STATUS (0x08) /* Remote Status Register */
#define RSR_PR_STATUS (1<<5) /* PR Interrupt is set */
#define RSR_NOT_LOCK_STATUS (1<<4) /* Remote bus is *NOT* locked */
#define RSR_PG_STATUS (1<<3) /* Page mode access is Enabled */
#define RSR_PT_STATUS (1<<1) /* PT interrupt is set */
/* The following bits apply to A32 VMEbus products ONLY */
#define RSR_WAS_RESET (1<<7) /* Remote bus was reset */
#define RSR_IACK2 (1<<2) /* IACK Read Mode Address Bit 2 */
#define RSR_IACK1 (1<<6) /* IACK Read Mode Address Bit 1 */
#define RSR_IACK0 (1<<0) /* IACK Read Mode Address Bit 0 */
/******************************************************************************
**
** Remote Command Register 2 (Read/Write, 8 Bits)
** THIS REGISTER DOES NOT APPLY TO A24 VMEbus
**
*******************************************************************************
** 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0
** +DMA_PAUS | +AMOD_SEL | +DMA_BLK | +INT_DIS | PGSZ3 | PGSZ2 | PGSZ1 | PGSZ0
******************************************************************************/
#define REM_CMD2 (0x09) /* Remote Command Register 2 */
/* The following bits apply to A32 DMA VMEbus products only */
#define RC2_DMA_PAUSE (1<<7) /* DMA remote pause after 16 xfers */
#define RC2_REM_AMOD_SEL (1<<6) /* Use remote address modifier reg. */
#define RC2_DMA_BLK_SEL (1<<5) /* Use remote block-mode DMA operatn */
#define RC2_CINT_DISABLE (1<<4) /* Disable passing of rem cable intr */
/* The following bits apply to all products */
#define RC2_PG_SIZE_64K (0x00) /* 64K Page Size */
#define RC2_PG_SIZE_128K (0x01) /* 128K Page Size */
#define RC2_PG_SIZE_256K (0x03) /* 256K Page Size */
#define RC2_PG_SIZE_512K (0x07) /* 512K Page Size */
#define RC2_PG_SIZE_1MB (0x0F) /* 1M Page Size */
#define RC2_PG_SIZE_MASK (0x0F) /* Page Size select mask */
/******************************************************************************
**
** Remote Node Address Page Register (Read/Write, 16 Bits)
**
******************************************************************************/
#define REM_PAGE (0x0A) /* Remote Address Page Register */
#define REM_PAGE_LO (0x0A) /* Address page byte - A16-A23 */
/* The following define applies to A32 VMEbus products only */
#define REM_PAGE_HI (0x0B) /* Address page byte - A24-A31 */
#define MIN_PAGE_SHIFT 16 /* 64k is minimum size (shift value) */
#define MAX_PAGE_SHIFT 20 /* 1MB maximum page size (shift value) */
#define QBUS_PG_MAX (0x3F) /* Needed for "bt_remid" to identify QBUS */
/******************************************************************************
**
** Remote Card ID Register (Read/Write, 8 Bits)
** A32 Products Only
**
******************************************************************************/
#define REM_CARD_ID (0x0C) /* Remote Card ID Register */
/******************************************************************************
**
** Remote Address Modifier Register (Read/Write, 8 Bits)
** VMEbus Products Only
**
******************************************************************************/
#define REM_AMOD (0x0D) /* Remote Address Modifier Register */
/******************************************************************************
**
** IACK Read Register (Read Only)
** VMEbus & Q-bus Only
**
******************************************************************************/
#define REM_IACK (0x0E) /* IACK Read Register */
#define REM_IACK_WORD (0x0E) /* IACK vector-D0-D7(word) */
#define REM_IACK_BYTE (0x0F) /* IACK vector-D0-D7(byte)D8-D15(word) */
/******************************************************************************
**
** DMA Registers
**
*******************************************************************************
**
** Local DMA Command Register (Read/Write, 8 Bits)
**
*******************************************************************************
** 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0
** +LDC_START | +DP_SEL | +WRT_SEL | +D32_SEL | 0 | +INT_EN | +DMA_DN | 0
******************************************************************************/
#define LDMA_CMD (0x10) /* Local DMA Command Register */
#define LDC_START (1<<7) /* Start DMA */
#define LDC_DP_SEL (1<<6) /* DMA to Dual-Port select */
#define LDC_WRITE_SEL (1<<5) /* DMA transfer direction */
#define LDC_DMA_D32_SEL (1<<4) /* DMA transfer size 16 / 32 bit data */
#define LDC_DMA_INT_ENABLE (1<<2) /* DMA done interrupt enable */
#define LDC_DMA_DONE (1<<1) /* DMA done indicator flag */
#define LDC_DMA_ACTIVE (1<<0) /* DMA in progress indicator flag */
/******************************************************************************
**
** Local DMA Remainder Count Register (Read/Write, 8 Bits)
**
******************************************************************************/
#define LDMA_RMD_CNT (0x11) /* Local DMA Remainder Count Register */
/*******************************************************************************
**
** Local DMA Packet Count Register (Read/Write, 16 Bits)
**
*******************************************************************************/
#define LDMA_PKT_CNT (0x12) /* Local DMA Packet Count Register */
#define LDMA_PKT_CNT_LO (0x12) /* Packet Count Byte - D0-D7 */
#define LDMA_PKT_CNT_HI (0x13) /* Packet Count Byte - D8-D15 */
#define LDMA_MIN_DMA_PKT_SIZE 4UL /* Minimum DMA Packet Size In Bytes */
#define LDMA_DMA_PKT_SIZE 8UL /* Standard DMA Packet Size Shift Val */
#define LDMA_MAX_XFER_LEN 0xFFFFFFL /* Maximum DMA transfer Size In Bytes */
/******************************************************************************
**
** Local DMA Address Registers (Read/Write)
**
*******************************************************************************/
#define LDMA_ADDR (0x14) /* Local DMA Address [indexes DMA map space] */
#define LDMA_ADDR_LO (0x14) /* Local DMA Address Byte - D0-D7 */
#define LDMA_ADDR_MID (0x15) /* Local DMA Address Byte - D8-D15 */
#define LDMA_ADDR_HI (0x16) /* Local DMA Address Byte - D8-D15 */
/******************************************************************************
**
** Remote DMA Packet Length Count Register (Read/Write)
**
******************************************************************************/
#define RDMA_LEN_CNT (0x18) /* Remote DMA 1st packet size */
/******************************************************************************
**
** Remote DMA Address Register (Read/Write)
**
******************************************************************************/
#define RDMA_ADDR (0x1A) /* Remote DMA Address */
#define RDMA_ADDR_HI (0x1A) /* Remote DMA Address (A31-A16) */
#define RDMA_ADDR_LO (0x1C) /* Remote DMA Address (A15-A0) */
/******************************************************************************
**
** Remote Slave Status Register (Read Only, 8 Bits)
**
*******************************************************************************
** 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0
** +PARITY |+REMBUS |+PR_INT |+CARD_RDY| 0 |+TIMEOUT|+LRC_ERR|+NOCONNECT
******************************************************************************/
#define REM_SLAVE_STATUS (0x1F) /* Local Status of remote card */
#define RSS_PARITY_ERR (1<<7) /* Interface Parity Error Remote->PCI */
#define RSS_REMBUS_ERR (1<<6) /* Invalid mapping RAM access or a */
/* data parity error occurred */
#define RSS_PR_STATUS (1<<5) /* PR interrupt set on the VME card */
#define RSS_TIMEOUT_ERR (1<<2) /* Interface Timeout error on DMA xfer */
#define RSS_PT_STATUS (1<<1) /* PT interrupt set on the VME card */
#define RSS_NO_CONNECT (1<<0) /* Rem. bus power / I/O cable is off */
#define RSS_ERROR_MASK (RSS_PARITY_ERR|RSS_REMBUS_ERR|RSS_TIMEOUT_ERR)
#define RSS_CERROR_MASK (RSS_NO_CONNECT|RSS_ERROR_MASK)
#endif /* KERNEL */
#endif