OpenSolaris_b135/cmd/terminfo/microterm.ti
#
# CDDL HEADER START
#
# The contents of this file are subject to the terms of the
# Common Development and Distribution License, Version 1.0 only
# (the "License"). You may not use this file except in compliance
# with the License.
#
# You can obtain a copy of the license at usr/src/OPENSOLARIS.LICENSE
# or http://www.opensolaris.org/os/licensing.
# See the License for the specific language governing permissions
# and limitations under the License.
#
# When distributing Covered Code, include this CDDL HEADER in each
# file and include the License file at usr/src/OPENSOLARIS.LICENSE.
# If applicable, add the following below this CDDL HEADER, with the
# fields enclosed by brackets "[]" replaced with your own identifying
# information: Portions Copyright [yyyy] [name of copyright owner]
#
# CDDL HEADER END
#
# Copyright (c) 1984, 1986, 1987, 1988, 1989 AT&T
# All Rights Reserved
#ident "%Z%%M% %I% %E% SMI" /* SVr4.0 1.6 */
# # --------------------------------
#
# microterm: MICROTERM
#
# Manufacturer: MICROTERM
# Class: III
microterm|act4|microterm act iv,
cr=^M, cud1=^J, ind=^J, bel=^G, am, cub1=^H, ed=^_, el=^^, clear=^L,
cup=^T%p1%c%p2%c, cols#80, lines#24, cuf1=^X, cuu1=^Z, home=^],
# Info:
# The padding on cuf1 for act5 and mime is a guess and not final.
# The act5 has hardware tabs, but in cols 8, 16, 24, 32, 41 (!), 49, ...
#
microterm5|act5|microterm act v,
uc=\EA, ri=\EH$<3>, kcuu1=^Z, kcud1=^K, kcub1=^H, kcuf1=^X, use=act4,
# Info:
# Act V in split screen mode. act5-s is not tested and said not
# to work.
# Could have been because of the funny tabs - it might work now.
#
act5-s|act5s|act 5 in split screen mode,
smcup=\EP, rmcup=\EQ, lines#48, cols#39, use=act5,
# Info:
# These mime1 entries refer to the Microterm Mime I or Mime II.
# The default mime is assumed to be in enhanced act iv mode.
# There is a ^Q in is2 to unwedge any lines that wedge on ^S.
#
mime|mime1|mime2|mimei|mimeii|microterm mime1,
cup=^T%p1%{24}%+%c%p2%?%p2%{32}%>%t%{48}%+%;%{80}%+%c, cols#80,
cr=^M, cud1=^J, ind=^J, bel=^G, il1=^A$<80>, am, cub1=^H,
ed=^_, el=^^, clear=\035^C, dl1=^W$<80>, ht=^I, lines#24,
cuf1=^X, it#8, uc=^U, cuu1=^z, home=\035, cud1=^K, is2=\E^S^Q,
kcuu1=^Z, kcud1=^K, kcub1=^H, kcuf1=^X, ri=^R$<3>, vt#9,
mime-na|mime with no arrow keys,
kcuu1@, kcud1@, kcuf1@, use=mime,
mime-3a|mime-adm3a|mime1 emulating adm3a,
cols#80, lines#24,
bel=^G, clear=^Z$<1>, cr=\r, cub1=\b, cud1=\n,
cuf1=\f, cup=\E=%p1%'\s'%+%c%p2%'\s'%+%c, cuu1=^K,
home=^^, ind=\n, kcub1=\b, kcud1=^K, kcuf1=^X,
kcuu1=^Z,
mime-3ax|mime-adm3ax|mime1 emulating enhanced adm3a,
il1=^A$<80>, dl1=^W$<80>, ht=^I$<3>, it#8, el=^X, ed=^_, use=mime-3a,
# Info:
# Mimes using brightness for standout. Half bright is very dim
# unless you turn up the brightness so far that lines show up on
# the screen.
#
mime-fb|full bright mime1,
smso=^Y, rmso=^S, is2=^S\E^Q, use=mime,
mime-hb|half bright mime1,
smso=^S, rmso=^Y, is2=^Y\E, use=mime,
# Info:
# These entries (for mime 2a) put the terminal in low intensity
# mode since high intensity mode is so obnoxious.
# This is the preferred mode (but ^X can't be used as a kill
# character (?))
#
mime2a|mime2a-v|microterm mime2a (emulating an enhanced vt52),
cr=^M, cud1=^J, ind=^J, bel=^G, il1=^A$<20*>, cub1=^H, ed=\EQ$<20*>,
cols#80, el=\EP, clear=\EL, cup=\EY%p1%' '%+%c%p2%' '%+%c, is2=^Y,
dch1=^N, dl1=^W$<20*>, ip=$<2>, rmir=^Z, home=\EH, smir=^O, cuu1=\EA,
ri=\EA, kcud1=\EB, kcub1=\ED, kcuf1=\EC, kcuu1=\EA, lines#24,
cuf1=\EC, ht=^I, it#8, rmso=\E9, smso=\E8, smul=\E4, rmul=\E5,
mime2a-s|microterm mime2a (emulating an enhanced soroc iq120),
cr=^M, cud1=^J, ind=^J, bel=^G, il1=^A$<20*>, am, cub1=^H, ed=\EJ$<20*>,
el=\EK, clear=\EL, cup=\E=%p1%' '%+%c%p2%' '%+%c, cols#80, dch1=\ED,
dl1=^W$<20*>, kcub1=^H, kcuf1=^L, kcuu1=^K, kcud1=^J, home=^^, is2=\E),
ri=\EI, smir=\EE, rmir=^Z, ip=$<2>, lines#24, cuf1=^L, cuu1=\EI,
smso=\E:, rmso=\E;, smul=\E6, rmul=\E7,
# Info:
# Wed Mar 9 18:53:21 1983
# We run our terminals at 2400 Baud, so there might be some timing
# problems at higher speeds.
# The major improvements in this mod are the terminal now
# scrolls down and insert mode works without redrawing the rest
# of the line to the right of the cursor. This is done with a
# bit of a kludge using the exit graphics mode to get out of
# insert, but it does not appear to hurt anything when using
# vi at least. If you have some users using act4's with programs
# that use curses and graphics mode this could be a problem.
#
mm3|mime314|mm314|mime 314,
am, cub1=^H, ht=^I, ed=^_, el=^^, clear=^L, cup=^T%p1%c%p2%c,
cols#80, lines#24, cuf1=^X, cuu1=^Z,
home=^], kcud1=^K, kcub1=^H, kcuf1=^X, kcuu1=^Z,
il1=^A, dch1=^D, dl1=^W, smir=^S, rmir=^V,
# Info:
# Fri Aug 5 08:11:57 1983
# this entry works for ergo 4000's with the following setups:
# ansi,wraparound,newline disabled, xon/xoff disabled in both
# setup a & c
#
# WARNING!!! There are multiple versions of ERGO 4000 microcode
# Be advised that very early versions DO NOT WORK RIGHT !!
# Microterm does have a ROM exchange program- use it or lose big
#
m8|ergo4000|microterm ergo 4000,
cr=^M, cud1=^J, ind=^J, bel=^G, ed=\E[0J$<15>, el=\E[0K$<13>,
clear=\E[H\E[2J$<80>, cub1=^H, cuf1=\E[C, cuu1=\E[A, cud1=\E[B,
cup=\E[%i%p1%d;%p2%dH, cols#80, lines#66, da, db, dch1=\E[1P$<80>,
il=\E[1L$<5*>, dl1=\E[1M$<5*>, smir=\E[4h$<6>, rmir=\E[4l,
is2=\E<\E=\E[?1l\E[?4l\E[?5l\E[?7h\E[?8h$<300>, kf1=\EOP,
kf2=\EOQ, kf3=\EOR, kf4=\EOS, kcud1=\E[B, rmkx=\E=$<4>,
kcub1=\E[D, kcuf1=\E[C, smkx=\E=$<4>, kcuu1=\E[A, lf1=pf1,
lf2=pf2, lf3=pf3, lf4=pf4, msgr, ht=^I, rmso=\E[0m$<20>,
smso=\E[7m$<20>, ri=\EM$<20*>, ind=\ED$<20*>,