V4/man/man5/fs.5
.th "FILE SYSTEM" V 9/7/73
.sh NAME
fs \*- format of file system volume
.sh DESCRIPTION
.ft I
Caution: this information applies only to
the latest versions of the UNIX system.
.s3
.ft R
Every
file system storage volume
(e.g. RF disk, RK disk, RP disk, DECtape reel)
has a common format for certain vital information.
Every such volume is divided into a certain number
of 256 word (512 byte) blocks.
Block 0 is unused and is available to contain
a bootstrap program, pack label, or other information.
.s3
Block 1 is the
.it "super block."
Starting from its first word, the format of a super-block is
.s3
.nf
struct {
int isize;
int fsize;
int nfree;
int free[100];
int ninode;
int inode[100];
char flock;
char ilock;
char fmod;
int time[2];
};
.s3
.fi
.it Isize
is the number of blocks devoted to the i-list,
which starts just after the super-block, in block 2.
.it Fsize
is the first block not potentially available for allocation
to a file.
This number is unused by the system, but is used by
programs like
.it "check (I)"
to test for bad block numbers.
The free list for each volume is maintained as
follows.
The
.it free
array contains, in
.it "free[1], ... , free[nfree\*-1],"
up to 99 numbers of free blocks.
.it Free[0]
is the block number of the head
of a chain of blocks constituting the free list.
The first word in each free-chain block is the number
(up to 100) of free-block numbers listed in the
next 100 words of this chain member.
The first of these 100 blocks is the link to the
next member of the chain.
To allocate a block:
decrement
.it nfree,
and the new block is
.it free[nfree].
If the new block number is 0,
there are no blocks left, so give an error.
If
.it nfree
became 0,
read in the block named by the new block number,
replace
.it nfree
by its first word,
and copy the block numbers in the next 100 words into the
.it free
array.
To free a block, check if
.it nfree
is 100; if so,
copy
.it nfree
and the
.it free
array into it,
write it out, and set
.it nfree
to 0.
In any event set
.it free[nfree]
to the freed block's number and
increment
.it nfree.
.s3
.it Ninode
is the number of free i-numbers in the
.it inode
array.
To allocate an i-node:
if
.it ninode
is greater than 0,
decrement it and return
.it inode[ninode].
If it was 0, read the i-list
and place the numbers of all free inodes
(up to 100) into the
.it inode
array,
then try again.
To free an i-node,
provided
.it ninode
is less than 100,
place its number into
.it inode[ninode]
and increment
.it ninode.
If
.it ninode
is already 100, don't bother to enter the freed i-node into any table.
This list of i-nodes is only to speed
up the allocation process; the information
as to whether the inode is really free
or not is maintained in the inode itself.
.s3
.it Flock
and
.it ilock
are flags maintained in the core
copy of the file system
while it is mounted
and their values on disk are immaterial.
The value of
.it fmod
on disk is likewise immaterial;
it is used as a flag to indicate that the super-block has
changed and should be copied to
the disk during the next periodic update of file
system information.
.s3
.it Time
is the last time the super-block of the file system was changed,
and is a double-precision representation
of the number of seconds that have elapsed
since
0000 Jan. 1 1970 (GMT).
During a reboot, the
.it time
of the super-block for the root file system
is used to set the system's idea of the time.
.s3
I-numbers begin at 1, and the storage for i-nodes
begins in block 2.
.tr |
Also, i-nodes are 32 bytes long, so 16 of them fit into a block.
Therefore, i-node
.it i
is located in block (\fIi\fR|+|31)|/|16, and begins
32\u\fB.\fR\d((\fIi\fR|+|31)|(mod 16) bytes from its start.
I-node 1 is reserved for the root directory of the file
system, but no other i-number has a built-in
meaning.
Each i-node represents one file.
The format of an i-node is as follows.
.s3
.nf
.if t .ta .5i 1.i 2.5i
struct {
int flags; /* +0: see below */
char nlinks; /* +2: number of links to file */
char uid; /* +3: user ID of owner */
char gid; /* +4: group ID of owner */
char size0; /* +5: high byte of 24-bit size */
int size1; /* +6: low word of 24-bit size */
int addr[8]; /* +8: block numbers or device number */
int actime[2]; /* +24: time of last access */
int modtime[2]; /* +28: time of last modification */
};
.dt
.fi
.s3
The flags are as follows:
.s3
.lp +10 9
100000 i-node is allocated
.lp +10 9
060000 2-bit file type:
.lp +15 9
000000 plain file
.lp +15 9
040000 directory
.lp +15 9
020000 character-type special file
.lp +15 9
060000 block-type special file.
.lp +10 9
010000 large file
.lp +10 9
004000 set user-ID on execution
.lp +10 9
002000 set group-ID on execution
.lp +10 9
000400 read (owner)
.lp +10 9
000200 write (owner)
.lp +10 9
000100 execute (owner)
.lp +10 9
000070 read, write, execute (group)
.lp +10 9
000007 read, write, execute (others)
.s3
.i0
Special files are recognized by their flags
and not by i-number.
A block-type special file is basically one which
can potentially be mounted as a file system;
a character-type special file cannot, though it is
not necessarily character-oriented.
For special files the high byte of the first address word
specifies the type of device; the low byte specifies
one of several devices of
that type.
The device type numbers
of block and character special files overlap.
.s3
The address words of ordinary files and directories
contain the numbers of the blocks in the
file (if it is small)
or the numbers of indirect blocks (if the file
is large).
.s3
Byte number
.it n
of a file is accessed as follows.
.it N
is divided by 512 to find its logical block number
(say
.it b
)
in the file.
If the file is small (flag 010000 is 0),
then
.it b
must be less than 8, and the physical
block number is
.it addr[b].
.s3
If the file is large,
.it b
is divided by 256 to yield
.it i,
and
.it addr[i]
is the physical block number of
the indirect block.
The remainder from the division
yields the word in the indirect block
which contains the number of the block for
the sought-for byte.
.s3
For block
.it b
in a file to exist,
it
is not necessary that all blocks less than
.it b
exist.
A zero block number either in the address words of
the i-node or in an indirect block indicates that the
corresponding block has never been allocated.
Such a missing block reads as if it contained all zero words.
.sh "SEE ALSO"
check (VIII)