TUHS December 2002

tuhs@tuhs.org

21 participants
40 discussions

Re: [TUHS] flaky webster or sigma WQESD4 and RQD11 controllers on KA650???

by Carl Lowenstein

> From: msokolov(a)ivan.Harhan.ORG (Michael Sokolov) > To: tuhs(a)tuhs.org > Subject: Re: [TUHS] flaky webster or sigma WQESD4 and RQD11 controllers on KA650??? > Date: Thu, 12 Dec 02 23:29:58 PST > > Robertdkeys(a)aol.com wrote: > > > Is there an endemic problem with this style 4 > > port controller running too fast with a KA650 > > compared to a KA630 cpu? > > I have no explanation for your problem, but it has nothing to do > with speed. Q-bus is Q-bus, and it follows Q-bus timing, which is > completely independent of the VAX CPU timing. Yes but there might be CPU spin-loop timing to run the serial maintenance port from the ROM bootstrap code of the controller. Not considered good form -- but such things happen. Some early version of the Sigma RQD11 would work in an 11/73 but not a KA630. I no longer remember the exact symptoms, but I was glad that at the time Sigma was only an 80-mile drive from here. carl -- carl lowenstein marine physical lab u.c. san diego clowenst(a)ucsd.edu

21 years, 4 months

Re: [TUHS] flaky webster or sigma WQESD4 and RQD11 controllers on KA650???

by Robertdkeys＠aol.com

I found out what the problem was.....(sheepishly ducking...(:+\\...). At 3 in the morning I had a typeo in the config file that the old eyeballs did not catch. I had typed in the partitions to allocate to root and swap, as opposed to just the the disks. It compiled fine, but when run, it paniced and dumped itself all over the floor. So much for myopic eyes programming at 3 in the morning..... (:+{{..... Bob

21 years, 4 months

Re: [TUHS] flaky webster or sigma WQESD4 and RQD11 controllers on KA650???

by msokolov＠ivan.Harhan.ORG

Robertdkeys(a)aol.com wrote: > Is there an endemic problem with this style 4 > port controller running too fast with a KA650 > compared to a KA630 cpu? I have no explanation for your problem, but it has nothing to do with speed. Q-bus is Q-bus, and it follows Q-bus timing, which is completely independent of the VAX CPU timing. Is the new CPU board firmly seated? Nothing broken or disturbed in the backplane when swapping the boards? > Ultrix seems to handle it better than Tahoe. > It might be speed in the hardware and slight > differences in drivers? Ultrix' MSCP code is vastly superior to anything we've ever had in BSD. I plan to lift the MSCP/SCA framework from Ultrix wholesale in Quasijarus down the line. MS

21 years, 4 months

re: Raise of interrupt level necessary

by Dennis Ritchie

Wolfgang Helbig wondered, > While studying the V6 kernel, I search for some rules as when to raise > the interrupt priority level (IPL). I came up with something like this: > A kernel process needs to raise the IPL if a change of data must be atomic and might > be accessed (not necessarily changed) by an IRS. > In light of this rule, some raising of interrupts seem unnecessary: > - In m40.s changes of the user space segmentation registers are bracketed by raising > and lowering the IPL, although these registers are never accessed by an ISR. > - Likewise, in m40.s, just before the trap routine checks the runrun flag and > restores r0, r1 and the user stackpointer, it raises the IPL. I can't see what > possibly should go wrong, if being interrupted while restoring the values. It's quite possible that the code is unnecessarily cautious. In general one does not want an interrupt while something sensitive is in a half-changed state (for example, some of the addressing registers changed, or a stack half-switched). For example, the clock interrupt routine can inspect user space (for display(), for example, though this is inactive on the 11/40), and even change it (for profiling). It does appear that other things (checking for a direct-from user-mode interrupt) in the clock routine already guard against these particular problems. It's been a long time since I've looked at this, however. Dennis

21 years, 4 months

flaky webster or sigma WQESD4 and RQD11 controllers on KA650???

by Robertdkeys＠aol.com

I upgraded my MVII KA630 critters to MVIII KA650 critters. The disk controllers in them are the old Webster or Sigma WQESD/4 and SCD-RQD11/EC (same boards). When I upgraded the cpu/ram on one of the machines, and tried to use the onboard formatter rs232 port, the port gave crazy spaces and backspaces continuously after the initial boot signon msg into the controller formatter prom. Changing it to a DQ696 controller and the problem went away. On a second machine, with KA650, it has a tendency to give uda controller initialization errors about 50% of the time when booting. Is there an endemic problem with this style 4 port controller running too fast with a KA650 compared to a KA630 cpu? It sure feels like that. It would be a bummer to have to use the slower cpus on these machines....(:+{{..... Anone else run into these kinds of problems? Ultrix seems to handle it better than Tahoe. It might be speed in the hardware and slight differences in drivers? Any suggestions or thoughts appreciated. Thanks Bob

21 years, 4 months

Re: [pups] 2.11BSD images for Simh

by Andru Luvisi

>From Warren: > > These file are now in the Unix Archive on minnie.tuhs.org in > PDP-11/Boot_Images/2.11_on_Simh > > The mirror sites should pick them up soon. >

21 years, 4 months

Re: [TUHS] Re: non-broken 4.3BSD set?

by msokolov＠ivan.Harhan.ORG

Robertdkeys(a)aol.com wrote: > I am wondering if > a dd image of a working few start blocks on a > disk could be copied over to a raw formatted > disk from the tape copy, before the miniroot > went on, as part of the boot/install process? This should work. > Michael, what are your thoughts on setting up > the disks, reasonably? Well, every time I need to do this, I do some history reenactment, as this is how Quasijarus Project was originally bootstrapped. I first install Ultrix on the VAX, then write a Tahoe/Quasijarus disk label to the boot disk (by compiling disklabel under Ultrix), and then do the normal 4.3-QJ0a install, at which point the standalone system sees the label and is happy. MS

21 years, 4 months

Re: [TUHS] Re: non-broken 4.3BSD set?

by msokolov＠ivan.Harhan.ORG

Robertdkeys(a)aol.com wrote: > Great! Keep me in mind for any testing if you > need it. I currently don't need any testing that I can't do myself, but thanks anyway. > I still am curious as to how many on the lists > are actually running such critters, currently, > on Quasijarus or on Ultrix. Well, Harhan is still up as you can see, despite the incessant bills... Pretty much all my work on Quasijarus since 4.3-QJ0a has been on operational issues, i.e., issues that don't matter much for hobbyists but become important when you use it operationally for your mission-critical computing. All my VAXen are running current unreleased code. The Internet feed is WorldCom/UUNET with a Quasijarus-based router. I wrote all the code for the latter, which will hopefully appear in 4.3-QJ1. I also have an MV3100 running Ultrix whose sole purpose is to interface an Exabyte 8 mm SCSI tape drive to my cluster. Doing backups on TK50s is prohibitively expensive. Some day I hope to find time to port 4.3-Quasijarus to it. > Did you arrive at any reasonable way to do the > initial disklabels and boot blocks so one can > install Quasijarus directly? That was and still is planned for 4.3-QJ1. 4.3-QJ0a and 4.3-QJ0b "officially" support bootstrap only on DEC RA disks. Two of my running MicroVAXen are equipped with the latter (RA72s). I also run one with ESDI disks, as I have equipped many MicroVAXen in the past. I bootstrap the latter via Ultrix (see my other reply). MS

21 years, 4 months

Re: [TUHS] Re: non-broken 4.3BSD set?

by Robertdkeys＠aol.com

That is what I do. After several failures, I find that using first NetBSD-1.4.1 boot to both label and install boot blocks, followed by second, NetBSD-1.2 boot and edlabel to trim the labels back to something akin to a Tahoe style label, seems to be the only way that works reliably. The label 1.4.1 writes is different from the Tahoe label, in that it computes incorrect c partition sizes. It does write something that I think is bootblock related that seems to must be there for Quasijarus to boot on my hardware. I am not sure exactly what it is, but using just the 1.2 edlabel does not seem to work reliably. The 1.2 edlabel seems to write a correct c size partition, though, after the 1.4.1 bits are put on. I ought to dd off the binary bits and see what is actually being written. But, the above seems to work, for me, and got my crashed disks back up a few minutes ago, after hours of prom formatting....(:+{{..... Anyway, that is how I get the machine up. If there is a better or easier way, someone holler. I am wondering if a dd image of a working few start blocks on a disk could be copied over to a raw formatted disk from the tape copy, before the miniroot went on, as part of the boot/install process? An undersized disk label with reasonably sized a and b partitions and a small but installable h partition (big enough for the usr tarball to fit on) should allow a bootable system to be installed. From that it could be set up on a second disk with correctly sized labels. Or, when the tape was written, a selection of disk boot/label images could be set up and a correct one written to the boot tape for the target disk install. What other ways could this be done? Michael, what are your thoughts on setting up the disks, reasonably? Thanks Bob

21 years, 4 months

Re: [TUHS] Re: non-broken 4.3BSD set?

by Robertdkeys＠aol.com

Great! Keep me in mind for any testing if you need it. I have 4 Qbus VAXentoyz that mostly just sit and play, when the HD's stay up. Of late ESDI drives have been giving me fits, but maybe I can scrounge up a few more in the local MooU surplus feeding frenzy diving pits. Maybe, someday, some scsi mscp cards might float up from the depths! (dream on.....(:+}}...) I still am curious as to how many on the lists are actually running such critters, currently, on Quasijarus or on Ultrix. I mostly play with mine, doing some roffing and TeXing, and porting a few minor tidbits. Did you arrive at any reasonable way to do the initial disklabels and boot blocks so one can install Quasijarus directly? The only clean way I can do it is to use two other OS installs that put enough bits there that Quasijarus is happy. There ought to be an easier way. Anyway, keep me posted as to when Quasijarus 0b might become reality. Thanks Bob Keys

21 years, 4 months

2024

2023

2022

2021

2020

2019

2018

2017

2016

2015

2014

2013

2012

2011

2010

2009

2008

2007

2006

2005

2004

2003

2002

2001

2000

1999

1998

1997

1996

1995

1994

1993

1992

1991

1990

TUHS December 2002