30 Jan
2002
30 Jan
'02
3:13 a.m.
On Jan 27, 23:42, lothar felten wrote:
installation was no problem, but still i
have some questions:
my VT102 doesn´t do backspace, i only
get ^H. i tried the
terminal in ANSI and VT52 mode, no
difference.
Maybe it wants a DEL character instead of backspace (backspace *is* ctrl-H,
shown as ^H or ^h). Change it on the terminal by going into setup, or use
stty on the BSD system to change the delete character (stty del '^h').
i have some dec boards labeled M7513
does anyone know what this
is? i found:
M7513 - RQD - RQDXE Q BUS drive
interface extension module
That's exactly what it is. The BA23 box only supports one hard drive; the
RQDXE is an adaptor for an RXDX2 or RXDX3 to permit use of additional
drives with a distribution board in a second enclosure. One of the 50-pin
connectors goes to the RQDX3, one to the distribution board in the BA23,
and the third to a connector kit on the rear panel of the BA23. There's a
different version for an RQDX1, called an RQDX1E.
the RQDX3 has another connector, i
suppose for RX50 floppydrive.
An RQDX3 has only one connector, the 50-pin one to go to the distribution
board. Are you looking at the right thing? Are you looking at a
distribution board? That does have a 34-way connector for a floppy.
can i hook up a 5,25" pc drive? maybe
with modifications?
Not an ordinary PC floppy, no. A TEAC FD55GFR is an 80-track double-sided
drive (not HD, though) that will work as an RX33. Some other 80-track
5.25" drives may work, if you set the jumpers.
--
Pete Peter Turnbull
Network Manager
University of York
30 Jan
30 Jan
3:03 p.m.
New subject: [pups] solution for the disklabel
On Wed, 30 Jan 2002, Pete Turnbull wrote:
On Jan 27, 23:42, lothar felten wrote:
On a real VT100 you cannot get the delete key to generate a backspace. He
must be pressing the backspace key, or he's not using a VT100 at all, but
instead some emulator, which isn't doing things the VT100 way...
Johnny
Johnny Billquist || "I'm on a bus
|| on a psychedelic trip
email: bqt(a)update.uu.se || Reading murder books
pdp is alive! || tryin' to stay hip" - B. Idol
installation was no problem, but still i
have some questions:
my VT102 doesn´t do backspace, i only
get ^H. i tried the
terminal in ANSI and VT52 mode, no
difference.
Maybe it wants a DEL character instead of backspace (backspace *is* ctrl-H,
shown as ^H or ^h). Change it on the terminal by going into setup, or use
stty on the BSD system to change the delete character (stty del '^h'). 
4 Feb
4 Feb
7:27 p.m.
New subject: [pups] VT102 and other hardware.... was: solution for the disklabel
Maybe it wants a DEL
character instead of
backspace (backspace *is* ctrl-H,
shown as ^H or ^h). Change
it on the
terminal by going
into setup, or use
stty on the BSD system to
change the
delete character
(stty del '^h').
On a real VT100 you cannot
get the delete key to
generate a backspace. He
must be pressing the
backspace key, or he's not
using a VT100 at all, but
instead some emulator, which
isn't doing things the VT100 way...
8127
days inactive
8132
days old
2 comments
3 participants
participants (3)
-
Johnny Billquist -
lothar felten -
pete＠dunnington.u-net.com